Driver Side Seat Belt Warning Light does not Operate
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When the ignition switch ON, the center airbag sensor assembly*1 (main body ECU [cowl side junction block LH]*2) transmits front seat inner belt state signals to the combination meter assembly through the CAN. If the driver seat belt is not fastened, the combination meter assembly blinks the driver side seat belt warning light. If the seat belt is fastened, the warning light goes off.- *1: w/ Airbag System
- *2: w/o Airbag System
WIRING DIAGRAM








INSPECTION PROCEDURE
| 1. CHECK VEHICLE TYPE |
Check vehicle type.
Result Result
Proceed to
w/ Airbag System
A
w/o Airbag System
B
|
|
||||
| A | |
| 2. CHECK FOR DTC |
Check for DTCs.
Result Result
Proceed to
DTC is not output
A
CAN system DTC is output (for LHD)
B
CAN system DTC is output (for RHD)
C
Airbag system DTC is output
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE BUCKLE SWITCH) |
Check the Data List for proper functioning of the driver side seat belt buckle switch.
SRS Airbag Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Driver Buckle SW
Driver side seat belt / Set, Unset or NG
Set: Driver side seat belt is fastened
Unset: Driver side seat belt is unfastened
NG: Data is not determined
Result Result
Proceed to
Set or Unset is displayed on the tester screen according to the driver side seat belt condition
A
Set or Unset is not displayed normally on the tester screen according to the driver side seat belt condition
B
NG is displayed on the tester screen
C
|
|
||||
|
|
||||
| A | |
| 4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER SIDE SEAT BELT WARNING LIGHT) |
Operate the intelligent tester according to the display and select Active Test.
Combination Meter Item
Test Part
Control Range
Diagnostic Note
Driver Side Seat Belt
Driver side seat belt warning light
ON/OFF
Confirm that the vehicle is stopped and the engine is idling.
- OK:
- Driver side seat belt warning light condition can be switched by Active Test.
| Result |
Proceed to |
| OK |
A |
| NG (w/ Multi-information Display) |
B |
| NG (w/o Multi-information Display) |
C |
|
|
||||
|
|
||||
| A | |
| 5. REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
Temporarily replace the center airbag sensor assembly with a new one (Click here).
| NEXT | |
| 6. CHECK DRIVER SIDE SEAT BELT WARNING LIGHT |
Check the driver side seat belt warning light function (Click here).
- OK:
- Driver side seat belt warning light operates normally.
Result Result
Proceed to
OK
A
NG (w/ Multi-information Display)
B
NG (w/o Multi-information Display)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK FOR DTC |
Check for DTCs.
| Result |
Proceed to |
| DTC is not output |
A |
| CAN system DTC is output (for LHD) |
B |
| CAN system DTC is output (for RHD) |
C |
|
|
||||
|
|
||||
| A | |
| 8. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE BUCKLE SWITCH) |
Check the Data List for proper functioning of the driver side seat belt buckle switch.
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Seat Buckle SW
Driver side seat belt / ON or OFF
ON: Driver side seat belt is fastened
OFF: Driver side seat belt is unfastened
-
- OK:
- The display is as specified in the normal condition column.
|
|
||||
| OK | |
| 9. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER SIDE SEAT BELT WARNING LIGHT) |
Operate the intelligent tester according to the steps on the display and select Active Test.
Combination Meter Item
Test Part
Control Range
Diagnostic Note
Driver Side Seat Belt
Driver side seat belt warning light
ON/OFF
Confirm that the vehicle is stopped and the engine is idling.
- OK:
- Driver side seat belt warning light condition can be switched by Active Test.
|
|
||||
| OK | ||
| ||
| 10. INSPECT FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) |
Remove the front seat inner belt assembly (for Driver Side) (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
12 - 9
Seat belt unfastened (buckle switch is off)
Below 1 Ω
Seat belt fastened (buckle switch is on)
10 kΩ or higher
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER AND BODY GROUND) |
Disconnect the K43*1 or L49*2 front seat inner belt assembly (for Driver Side) connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the E1 main body ECU (cowl side junction block LH) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
K43-12 - E1-7 (DBKL)
Always
Below 1 Ω
K43-12 or E1-7 (DBKL) - Body ground
Always
10 kΩ or higher
K43-9 - Body ground
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
L49-12 - E1-7 (DBKL)
Always
Below 1 Ω
L49-12 or E1-7 (DBKL) - Body ground
Always
10 kΩ or higher
L49-9 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
