2011-2013 Land Cruiser · Service Manual Vehicle Interior

Driver Side Seat Belt Warning Light does not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the ignition switch ON, the center airbag sensor assembly*1 (main body ECU [cowl side junction block LH]*2) transmits front seat inner belt state signals to the combination meter assembly through the CAN. If the driver seat belt is not fastened, the combination meter assembly blinks the driver side seat belt warning light. If the seat belt is fastened, the warning light goes off.
  1. *1: w/ Airbag System
  2. *2: w/o Airbag System

WIRING DIAGRAM

C247025E01
C246934E01
C247025E02
C246934E02

INSPECTION PROCEDURE


1. CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result 
    Result
    Proceed to
    w/ Airbag System
    A
    w/o Airbag System
    B



B
Go to step 7
A


2. CHECK FOR DTC
  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    CAN system DTC is output (for LHD)
    B
    CAN system DTC is output (for RHD)
    C
    Airbag system DTC is output
    D



B
Go to CAN COMMUNICATION SYSTEM (Click here)

C
Go to CAN COMMUNICATION SYSTEM (Click here)

D
Go to AIRBAG SYSTEM (Click here)
A


3. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE BUCKLE SWITCH)
  1. Check the Data List for proper functioning of the driver side seat belt buckle switch.

    SRS Airbag 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Driver Buckle SW
    Driver side seat belt / Set, Unset or NG
    Set: Driver side seat belt is fastened
    Unset: Driver side seat belt is unfastened
    NG: Data is not determined
    Result 
    Result
    Proceed to
    Set or Unset is displayed on the tester screen according to the driver side seat belt condition
    A
    Set or Unset is not displayed normally on the tester screen according to the driver side seat belt condition
    B
    NG is displayed on the tester screen
    C



B
REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER SIDE SEAT BELT WARNING LIGHT)
  1. Operate the intelligent tester according to the display and select Active Test.

    Combination Meter 
    Item
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Driver side seat belt warning light
    ON/OFF
    Confirm that the vehicle is stopped and the engine is idling.

    OK:
    Driver side seat belt warning light condition can be switched by Active Test.

Result 
Result
Proceed to
OK
A
NG (w/ Multi-information Display)
B
NG (w/o Multi-information Display)
C


B
REPLACE COMBINATION METER (Click here)

C
REPLACE COMBINATION METER (Click here)
A


5. REPLACE CENTER AIRBAG SENSOR ASSEMBLY
  1. Temporarily replace the center airbag sensor assembly with a new one (Click here).


NEXT


6. CHECK DRIVER SIDE SEAT BELT WARNING LIGHT
  1. Check the driver side seat belt warning light function (Click here).

    OK:
    Driver side seat belt warning light operates normally.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Multi-information Display)
    B
    NG (w/o Multi-information Display)
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

END (CENTER AIRBAG SENSOR ASSEMBLY IS DEFECTIVE)

7. CHECK FOR DTC
  1. Check for DTCs.

Result 
Result
Proceed to
DTC is not output
A
CAN system DTC is output (for LHD)
B
CAN system DTC is output (for RHD)
C


B
Go to CAN COMMUNICATION SYSTEM (Click here)

C
Go to CAN COMMUNICATION SYSTEM (Click here)
A


8. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE BUCKLE SWITCH)
  1. Check the Data List for proper functioning of the driver side seat belt buckle switch.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Seat Buckle SW
    Driver side seat belt / ON or OFF
    ON: Driver side seat belt is fastened
    OFF: Driver side seat belt is unfastened
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 10
OK


9. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER SIDE SEAT BELT WARNING LIGHT)
  1. Operate the intelligent tester according to the steps on the display and select Active Test.

    Combination Meter 
    Item
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Driver side seat belt warning light
    ON/OFF
    Confirm that the vehicle is stopped and the engine is idling.

    OK:
    Driver side seat belt warning light condition can be switched by Active Test.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

10. INSPECT FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

  1. C246933
    Remove the front seat inner belt assembly (for Driver Side) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    12 - 9
    Seat belt unfastened (buckle switch is off)
    Below 1 Ω
    Seat belt fastened (buckle switch is on)
    10 kΩ or higher



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) (Click here)
OK


11. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER AND BODY GROUND)
  1. Disconnect the K43*1 or L49*2 front seat inner belt assembly (for Driver Side) connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the E1 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    K43-12 - E1-7 (DBKL)
    Always
    Below 1 Ω
    K43-12 or E1-7 (DBKL) - Body ground
    Always
    10 kΩ or higher
    K43-9 - Body ground
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    L49-12 - E1-7 (DBKL)
    Always
    Below 1 Ω
    L49-12 or E1-7 (DBKL) - Body ground
    Always
    10 kΩ or higher
    L49-9 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


← DATA LIST / ACTIVE TEST (from Sep 2011)Driver Side Seat Belt Warning Light does not Operate (from Jan 2012) →