2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).
A165943E02
DTC Code
DTC Detection Condition
Trouble Area
P0660
Conditions (a) and (b) are met for 0.5 sec. or more (2 trip detection logic):
(a) The voltage of terminal ACIS of the ECM is low when the VSV is OFF.
(b) The engine has started.
  1. Open or short in VSV for ACIS circuit
  2. VSV for ACIS
  3. ECM

WIRING DIAGRAM

A161384E05

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE VSV FOR ACIS)
A067588E05
  1. Disconnect the vacuum hose.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Active the VSV for Intake Control. Operate the VSV for ACIS.

  1. Check the VSV operation when it is operated using the tester.

    Standard:
    Tester Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter



NG
Go to step 4
OK


2. CHECK VACUUM HOSE
  1. Check that the vacuum hose is connected correctly, and that there are no cracks, holes, damage, or looseness.

    OK:
    Vacuum hose is normal.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


3. INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)
  1. Inspect the intake air control valve (Click here).



NG
REPLACE INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE) (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. INSPECT VSV FOR ACIS (OPERATION)
  1. Inspect the VSV for ACIS (Click here).



NG
REPLACE VSV FOR ACIS (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM, VSV FOR ACIS - EFI NO. 2 FUSE)
A187315E02
  1. Check the wire harness and connectors between the VSV for ACIS and ECM.

    1. Disconnect the VSV for ACIS connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C129-2 - C45-62 (ACIS)
      Always
      Below 1 Ω
      C129-2 or C45-62 (ACIS) - Body ground
      Always
      10 kΩ or higher

  1. Check the wire harness between the VSV for ACIS and EFI NO. 2 fuse.

    1. Disconnect the VSV for ACIS connector.

    2. Remove the EFI NO. 2 fuse from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C129-1 - EFI NO. 2 fuse
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0657 Actuator Supply Voltage Circuit / Open (from Jan 2012)P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (from Jan 2012) →