2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).
When the engine speed is between 2200 rpm and 4100 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the VSV (ON status), to close the IACV. Under other conditions, the VSV is usually OFF and the IACV is open.
A115903E03
DTC Code
DTC Detection Condition
Trouble Area
P0660
Conditions (a) and (b) are met for 0.5 sec. or more (2 trip detection logic):
(a) The voltage of terminal ACIS of the ECM is low when the VSV is OFF.
(b) The engine has started.
  1. Open or short in VSV for ACIS circuit
  2. VSV for ACIS
  3. ECM

WIRING DIAGRAM

A161384E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE VSV FOR ACIS)
A067588E05
  1. Disconnect the vacuum hose.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Active the VSV for Intake Control. Operate the VSV for ACIS.

  1. Check the VSV operation when it is operated using the intelligent tester.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

  1. Reconnect the vacuum hose.



B
Go to step 4
A


2. INSPECT VSV FOR ACIS (OPERATION)
  1. Inspect the VSV for ACIS (Click here).



NG
REPLACE VSV FOR ACIS (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM, VSV FOR ACIS - EFI NO. 2 FUSE)
A182332E01
  1. Check the wire harness and connectors between the VSV for ACIS and ECM.

    1. Disconnect the VSV for ACIS connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      C31-2 - C45-107 (ACIS)
      Always
      Below 1 Ω
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      C31-2 - C46-107 (ACIS)
      Always
      Below 1 Ω


      Standard Resistance (Check for Short):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      C31-2 or C45-107 (ACIS) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      C31-2 or C46-107 (ACIS) - Body ground
      Always
      10 kΩ or higher

  1. Check the wire harness between the VSV for ACIS and EFI NO. 2 fuse.

    1. Disconnect the VSV for ACIS connector.

    2. Remove the EFI NO. 2 fuse from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      Tester Connection
      Condition
      Specified Condition
      C31-1 - EFI NO. 2 fuse
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK VACUUM HOSE
  1. Check that the vacuum hose is connected correctly, and that there are no cracks, holes, damage, or looseness.

    OK:
    Vacuum hose is normal.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


5. INSPECT INTAKE AIR SURGE TANK (INTAKE AIR CONTROL VALVE)

  1. A075984E02
    Check that the lever moves when a vacuum of 26.6 kPa (200 mmHg, 7.85 in.Hg) is applied with the vacuum gauge on.

    OK:
    Lever moves.

  1. Check that the vacuum of 26.6 kPa (200 mmHg, 7.85 in.Hg) is sustained for 1 minute in the above state.

    OK:
    Vacuum is sustained.



NG
REPLACE INTAKE AIR SURGE TANK (INTAKE AIR CONTROL VALVE) (Click here)
OK

REPLACE ECM (Click here)


← P0657 Actuator Supply Voltage Circuit / Open (from Jan 2012)P0724 Brake Switch "B" Circuit High (Sep 2011 – Dec 2011) →