2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The stop light switch assembly is a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly.
The purpose of this circuit is to prevent the engine from stalling while driving with the lock-up torque converter clutch on when the brakes are suddenly applied.
When the brake pedal is depressed, the stop light switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC Code
DTC Detection Condition
Trouble Area
P0724
The stop light switch remains on even when vehicle is driven in a GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
  1. Short in stop light switch signal circuit
  2. Stop light switch assembly
  3. ECM

WIRING DIAGRAM

Refer to DTC P0504 (Click here).

INSPECTION PROCEDURE

HINT:
  1. Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.

  1. Read the value displayed on the tester when the brake pedal is depressed and released.

    OK:
    Brake Pedal
    Display
    Released
    OFF
    Depressed
    ON



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. A167698E02
    Disconnect the stop light switch assembly connector.

  1. Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

  1. Reinstall the stop light switch assembly.

  1. Reconnect the stop light switch assembly connector.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

  1. A112585E53
    Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-36 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    0 to 3 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-36 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    0 to 3 V

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) (Sep 2011 – Dec 2011)P0724 Brake Switch "B" Circuit High (from Jan 2012) →