2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B1593 No Response from Stereo Component Amplifier

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The display and navigation module display and stereo component amplifier assembly are connected by the MOST communication line.
When an MOST communication error occurs between the display and navigation module display and stereo component amplifier assembly, these DTCs will be stored.
DTC No.
DTC Detection Condition
Trouble Area
B1593
No response to the diagnostic memory request from the master unit.
  1. Stereo component amplifier assembly power source circuit
  2. MOST circuit between radio receiver assembly and stereo component amplifier assembly
  3. MOST circuit between stereo component amplifier assembly and display and navigation module display (w/o Rear Seat Entertainment System)
  4. MOST circuit between stereo component amplifier assembly and television display assembly (w/ Rear Seat Entertainment System)
  5. Stereo component amplifier assembly
  6. Display and navigation module display
B15D3
A device that is listed in the MOST network connected device record of the master unit is missing.

HINT:
For the MOST network, the display and navigation module display is the master unit.


WIRING DIAGRAM

E194865E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
      2. This DTC may be stored when an MOST communication error occurs due to electrical noise.



B
Go to step 3
A


2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END

4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)

  1. E192419E01
    Disconnect the F2 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F2-2 (GND) - Body ground
    Always
    Below 1 Ω
    F2-6 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F2-1 (+B) - F2-2 (GND)
    Always
    11 to 14 V
    F2-3 (+B2) - F2-2 (GND)
    Always
    11 to 14 V

Text in Illustration 
*1
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - RADIO RECEIVER)
  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Disconnect the F56 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F59-4 (MI+) - F56-11 (MO+)
    Always
    Below 1 Ω
    F59-10 (MI-) - F56-25 (MO-)
    Always
    Below 1 Ω
    F59-5 (SLDI) - F56-24 (SLDI)
    Always
    Below 1 Ω
    F59-4 (MI+) - Body ground
    Always
    10 kΩ or higher
    F59-10 (MI-) - Body ground
    Always
    10 kΩ or higher
    F59-5 (SLDI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CONFIRM MODEL
  1. Choose the model to be inspected.

    Result 
    Model
    Proceed to
    w/o Rear Seat Entertainment System
    A
    w/ Rear Seat Entertainment System
    B



B
Go to step 9
A


7. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - DISPLAY AND NAVIGATION MODULE)
  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Disconnect the F65 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F59-6 (MO+) - F65-1 (MI+)
    Always
    Below 1 Ω
    F59-12 (MO-) - F65-5 (MI-)
    Always
    Below 1 Ω
    F59-11 (SLDO) - F65-2 (SLDI)
    Always
    Below 1 Ω
    F59-6 (MO+) - Body ground
    Always
    10 kΩ or higher
    F59-12 (MO-) - Body ground
    Always
    10 kΩ or higher
    F59-11 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

END

9. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - TELEVISION DISPLAY)
  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Disconnect the L39 television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F59-6 (MO+) - L39-1 (MI+)
    Always
    Below 1 Ω
    F59-12 (MO-) - L39-2 (MI-)
    Always
    Below 1 Ω
    F59-11 (SLDO) - L39-3 (SLDI)
    Always
    Below 1 Ω
    F59-6 (MO+) - Body ground
    Always
    10 kΩ or higher
    F59-12 (MO-) - Body ground
    Always
    10 kΩ or higher
    F59-11 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

END


← B1591 No Response from Audio HU (+ B15D1) (Sep 2011 – Dec 2011)B1595 No Response from Rear Seat Entertainment System (+ B15D5) (Sep 2011 – Dec 2011) →