2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B1591 No Response from Audio HU

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The display and navigation module display and radio receiver assembly are connected by the MOST communication line.
When an MOST communication error occurs between the display and navigation module display and the radio receiver assembly, these DTCs will be stored.
DTC No.
DTC Detection Condition
Trouble Area
B1591
Within the time-out period, there was no response from the radio receiver assembly to the following requests from the master unit:
  1. System inspection request
  2. System inspection result request
  3. Diagnostic memory request
  1. Radio receiver assembly power source circuit
  2. MOST circuit between display and navigation module display and radio receiver assembly
  3. MOST circuit between radio receiver assembly and stereo component amplifier assembly
  4. Radio receiver assembly
  5. Display and navigation module display
B15D1*1
When either of the conditions below is met:
  1. Radio receiver assembly is/was not connected while the engine switch is on (IG or ACC).
  2. Communication between the master unit and the radio receiver assembly is not possible when the engine is started.

HINT:
  1. *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The display and navigation module display is the master unit.


WIRING DIAGRAM

E194864E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
      2. This DTC may be stored when an MOST communication error occurs due to electrical noise.



B
Go to step 3
A


2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END

4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY POWER SOURCE)

  1. E192430E09
    Disconnect the F56 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F56-15 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F56-14 (B) - F56-15 (GND)
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - RADIO RECEIVER)
  1. Disconnect the F65 display and navigation module display connector.

  1. Disconnect the F56 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F65-3 (MO+) - F56-9 (MI+)
    Always
    Below 1 Ω
    F65-7 (MO-) - F56-23 (MI-)
    Always
    Below 1 Ω
    F65-6 (SLDO) - F56-10 (SLDI)
    Always
    Below 1 Ω
    F65-3 (MO+) - Body ground
    Always
    10 kΩ or higher
    F65-7 (MO-) - Body ground
    Always
    10 kΩ or higher
    F65-6 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO COMPONENT AMPLIFIER)
  1. Disconnect the F56 radio receiver assembly connector.

  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F56-11 (MO+) - F59-4 (MI+)
    Always
    Below 1 Ω
    F56-25 (MO-) - F59-10 (MI-)
    Always
    Below 1 Ω
    F56-24 (SLDI) - F59-5 (SLDI)
    Always
    Below 1 Ω
    F56-11 (MO+) - Body ground
    Always
    10 kΩ or higher
    F56-25 (MO-) - Body ground
    Always
    10 kΩ or higher
    F56-24 (SLDI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. REPLACE RADIO RECEIVER ASSEMBLY
  1. Replace the radio receiver assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

END


← B1582 Map Disk Reading Malfunction (Sep 2011 – Dec 2011)B1593 No Response from Stereo Component Amplifier (+ B15D3) (Sep 2011 – Dec 2011) →