2011-2013 Land Cruiser · Service Manual Drivetrain

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY

C178826E01
  1. Using a vernier caliper and straightedge, measure dimension A between the end surface of the engine and the torque converter contact surface of the drive plate.

  1. Install the torque converter clutch to the transmission housing.

  1. Z036073E05
    Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is more than A measured in the first step.

    Standard distance:
    B = A + 1.00 mm (0.0394 in.) or more


2. INSTALL TRANSFER ASSEMBLY

C171523
  1. Install the transfer with the 8 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Be careful not to damage the oil seal of the transfer adapter.

  1. C171493
    Install the transfer case lower protector with the 7 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Connect the clamp of the ground cable to the transfer case lower protector.

  1. C171500
    Attach the 2 breather hose clamps to connect the transfer breather hose to the automatic transmission breather tube.


3. INSTALL HARNESS CLAMP BRACKET
  1. Install the 2 harness clamp brackets with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

C171497E01

NOTICE:
Check that the 2 straight pins are attached to the engine side.

  1. Install the transmission with the 9 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


5. CONNECT OIL COOLER TUBE

C171504E01
  1. Temporarily install the oil cooler tube to the engine with the bolt A. Install the bolt B and tighten it to the specified torque. Then tighten the bolt A to the specified torque.

    Torque:
    14 N*m{ 143 kgf*cm , 21 ft.*lbf }

  1. Connect the 2 transmission oil cooler hoses to the oil cooler tube union.

    NOTICE:
    1. Make sure the pinching portion of each clip is facing the direction shown in the illustration.
    2. Make sure the paint mark of each hose is facing outward.


6. CONNECT BREATHER PLUG HOSE

C171499
  1. Connect the breather plug hose and attach the transfer breather hose.


7. INSTALL NO. 2 MANIFOLD STAY

C171486
  1. Install the stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


8. INSTALL MANIFOLD STAY

C171485
  1. Install the stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


9. CONNECT WIRE HARNESS AND CONNECTOR

  1. Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and 2 transfer control side connectors.

    C171495E02

    HINT:
    Push up the lever until the claw of the transmission wire connector makes a connection sound.

  1. Connect the harness with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 connector clamps and 6 harness clamps.

  1. Tilt up the automatic transmission.

  1. C171503
    Connect the ground cable with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


10. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

C171491
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    59 N*m{ 602 kgf*cm , 44 ft.*lbf }


11. INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C171489
  1. Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. C171490E01
    Install the frame crossmember to the frame with the 4 bolts and 4 nuts.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }

  1. C171484
    Install the engine mounting hole cover.


12. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

C157017
  1. Turn the crankshaft to gain access to the installation locations of the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then install the remaining 5 bolts.

  1. C157016
    Install the flywheel housing side cover.


13. INSTALL STARTER ASSEMBLY (for 1.4 kW Type)

  1. A223812
    Install the starter with the 2 bolts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }

  1. Connect the starter connector.

  1. A223811
    Connect the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the terminal cap.


14. CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828
  1. Connect the gear shifting rod to the transmission control shaft lever RH with the pin and a new clip.


15. INSTALL EXHAUST PIPE
(Click here)

16. INSTALL PROPELLER SHAFT ASSEMBLY
(Click here)

17. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)

18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


19. ADD AUTOMATIC TRANSMISSION FLUID
(Click here)

20. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that it moves smoothly and correctly into position.

  1. Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.
    If there are no problems during the above inspections, perform the adjustment using the following procedures.

    1. Move the shift lever to N

    2. C172428E01
      Loosen the nut of the floor shift gear shifting rod. Then, with the lever of the floor shift assembly lightly pushed towards the rear of the vehicle, tighten the nut.

      Torque:
      13 N*m{ 130 kgf*cm , 9 ft.*lbf }


21. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

22. INSTALL FRONT FENDER APRON SEAL LH

  1. A176301
    Install the fender apron seal with the 4 clips.


23. INSTALL FRONT FENDER APRON SEAL REAR LH

  1. A177005
    Install the fender apron seal with the 4 clips.


24. INSTALL FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Install the fender apron seal with the 3 clips.


25. INSTALL FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Install the fender apron seal with the 4 clips.


26. INSTALL NO. 1 ENGINE UNDER COVER

C173929
  1. Install the under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


27. INSTALL NO. 2 ENGINE UNDER COVER

C173930
  1. Install the under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


28. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


29. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


30. RESET MEMORY
  1. Perform the Reset Memory procedures (A/T initialization) (Click here).

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →