2011-2013 Land Cruiser · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


5. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 2 bolts and No. 2 engine under cover.


6. REMOVE NO. 1 ENGINE UNDER COVER

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover.


7. REMOVE FRONT FENDER APRON TRIM PACKING B

  1. A177004
    w/ KDSS:
    Remove the 3 clips and front fender apron trim packing B.

  1. A176301
    w/o KDSS:
    Remove the 4 clips and front fender apron trim packing B.


8. REMOVE FRONT FENDER APRON TRIM PACKING D

  1. A177005
    Remove the 4 clips and front fender apron trim packing D.


9. REMOVE FRONT FENDER APRON TRIM PACKING A

  1. A177003
    Remove the 3 clips and front fender apron trim packing A.


10. REMOVE FRONT FENDER APRON TRIM PACKING C

  1. A177002
    Remove the 4 clips and front fender apron trim packing C.


11. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)

13. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)

14. REMOVE EXHAUST PIPE
(Click here)

15. DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828
  1. Remove the clip and pin, and disconnect the gear shifting rod from the transmission control shaft lever RH.


16. REMOVE STARTER ASSEMBLY
(Click here)

17. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

C157016
  1. Remove the flywheel housing side cover.

  1. C157017
    Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.


18. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C159641
  1. Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.


19. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C171484
  1. Remove the engine mounting hole cover.

  1. C171489
    Remove the 4 bolts of the rear engine mounting insulator.

  1. C171490E01
    Remove the 4 nuts, 4 bolts and frame crossmember.


20. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

  1. C171491
    Remove the 4 bolts and rear engine mounting insulator from the transmission.


21. DISCONNECT WIRE HARNESS AND CONNECTOR

C171503
  1. Remove the bolt and disconnect the ground cable.

  1. C157274
    Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 transmission speed sensor connectors and 2 transfer control side connectors.

    C171495E01

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.

  1. Disconnect the 2 connector clamps and 6 harness clamps.

  1. Remove the bolt and disconnect the wire harness.


22. REMOVE MANIFOLD STAY

C171485
  1. Remove the 3 bolts and stay.


23. REMOVE NO. 2 MANIFOLD STAY

C171486
  1. Remove the 3 bolts and stay.


24. DISCONNECT BREATHER PLUG HOSE

C171499
  1. Disconnect the breather plug hose and detach the transfer breather hose.


25. DISCONNECT OIL COOLER TUBE

C173933
  1. Remove the 2 bolts and disconnect the 2 hoses from the transmission, and separate the oil cooler tube from the engine.


26. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C171497
  1. Remove the 9 bolts and transmission.

    NOTICE:
    Do not use excess force when prying the transmission assembly.


27. REMOVE TRANSFER ASSEMBLY

C171500
  1. Detach the 2 breather hose clamps from the automatic transmission breather tube.

  1. Disconnect the clamp of the ground cable from the transfer case lower protector.

  1. C171493
    Remove the 7 bolts and transfer case lower protector.

  1. C171523
    Remove the 8 bolts and transfer.


28. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

29. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

  1. Inspect the 1-way clutch.

    1. Install SST to the inner race of the 1-way clutch.

      SST
      09350-32014   (09351-32020)

    2. AT05437E01
      Press on the serrations of the starter with a finger and rotate it.
      Check that it rotates smoothly when turned clockwise and locks when turned counterclockwise.
      If the results are not as specified, clean the converter and recheck the 1-way clutch. If the results still are not as specified, replace the torque converter clutch assembly.

  1. D025367E04
    Determine the condition of the torque converter clutch.

    1. Check that the following conditions are met:

      1. During the stall test or when the shift lever is in N, metallic sounds are not emitted from the torque converter clutch.
      2. The 1-way clutch turns in one direction and locks in the other direction.
      3. The amount of powder in the ATF is not more than the sample shown in the illustration.
      If the results are not as specified, replace the torque converter clutch assembly.

      HINT:
      The sample illustration shows approximately 0.25 liters (0.26 US qts, 0.22 Imp. qts) of ATF taken from a removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter clutch thoroughly and drain the ATF with the torque converter facing upward.

  1. D025368E05
    Prevent deformation of the torque converter clutch and damage to the oil pump gear.

    1. When any marks due to interference are found on the end of the bolt for the torque converter clutch and on the bottom of the bolt hole, replace the bolt and torque converter clutch.

    2. All of the bolts should be the same length.

    3. Make sure no spring washers are missing.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →