2011-2013 Land Cruiser · Service Manual Drivetrain

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY

C178827E01
  1. Using a vernier caliper and straightedge, measure dimension A between the end surface of the engine and the torque converter contact surface of the drive plate.

  1. Install the torque converter clutch to the transmission housing.

  1. C123813E03
    Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is more than A measured in the first step.

    Standard distance:
    B = A + 1.00 mm (0.0394 in.) or more


2. INSTALL TRANSFER ASSEMBLY

C171523
  1. Install the transfer with the 8 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Be careful not to damage the oil seal of the transfer adapter.

  1. C171493
    Install the transfer case lower protector with the 7 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Connect the cable of the ground cable to the transfer case lower protector.

  1. C171502
    Attach the 2 breather hose clamps to connect the transfer breather hose to the automatic transmission breather tube, and install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


3. INSTALL HARNESS CLAMP BRACKET
  1. Install the front left bank bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the rear left bank bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. w/o Air Cooled Transmission Oil Cooler:
    Install the front right bank bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. Install the rear right bank bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

C171498E01

NOTICE:
Check that the 2 straight pins are attached to the engine side.

  1. Install the transmission with the 6 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


5. INSTALL MANIFOLD STAY

C172402E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    for bolt A:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    for bolt B:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }


6. INSTALL NO. 2 MANIFOLD STAY

C172401E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    for bolt A:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    for bolt B:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }


7. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Air Cooled Transmission Oil Cooler)

C178814E01
  1. Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

  1. Align the transmission oil cooler with the transmission oil thermostat and assemble them with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 oil cooler hoses to the transmission oil thermostat with the 2 clips.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  1. Temporarily install the transmission oil cooler with the transmission oil thermostat with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. C175552E01
    Connect the 2 hoses with the 2 clips.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.


8. CONNECT NO. 2 WATER BY-PASS PIPE (w/o Air Cooled Transmission Oil Cooler)

C157030E01
  1. Connect the 2 water by-pass hoses with the 2 clips and connect the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Make sure the pinching portion of each clip is facing the direction shown in the illustration.
    2. Make sure the paint mark of each hose is facing outward.

  1. C175551
    Install the hose heat protector with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


9. CONNECT TRANSMISSION OIL COOLER HOSE (w/o Air Cooled Transmission Oil Cooler)

C155914
  1. Connect the 2 oil cooler hoses to the transmission oil thermostat.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.


10. CONNECT TRANSMISSION OIL COOLER HOSE (w/ Air Cooled Transmission Oil Cooler)

C171509E01
  1. Connect the 2 transmission oil cooler hoses to the transmission.

    NOTICE:
    1. Make sure the pinching portion of each clip is facing the direction shown in the illustration.
    2. Make sure the paint mark of each hose is facing outward.


11. CONNECT WIRE HARNESS AND CONNECTOR

C171496E02
  1. Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and 2 transfer control side connectors.

    HINT:
    Push up the lever until the claw of the transmission wire connector makes a connection sound.

  1. Connect the wire harness with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 4 connector clamps and 7 harness clamps.

  1. Tilt up the automatic transmission.

  1. C171503
    Connect the ground cable with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


12. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

C171492
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    59 N*m{ 602 kgf*cm , 44 ft.*lbf }


13. INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C171489
  1. Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. C171490E01
    Install the frame crossmember to the frame with the 4 bolts and 4 nuts.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }

  1. C171484
    Install the engine mounting hole cover.


14. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

C155911
  1. Turn the crankshaft to gain access to the installation location of the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then install the remaining 5 bolts.

  1. C155910
    Install the flywheel housing under cover with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


15. CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828
  1. Connect the gear shifting rod to the transmission control shaft lever RH with a new clip and pin.


16. INSTALL EXHAUST PIPE
(Click here)

17. INSTALL PROPELLER SHAFT ASSEMBLY
(Click here)

18. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here).

19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


20. ADD ENGINE COOLANT (w/o Air Cooled Transmission Oil Cooler)
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    w/o Transmission oil cooler
    w/o Rear Heater
    13.4 liters (14.2 US qts, 11.8 Imp. qts)
    w/ Rear Heater
    16.3 liters (17.2 US qts, 14.3 Imp. qts)
    w/ Transmission oil cooler
    w/o Rear Heater
    14.1 liters (14.9 US qts, 12.4 Imp. qts)
    w/ Rear Heater
    16.9 liters (17.9 US qts, 14.9 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A168577
    Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the radiator reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    NOTICE:
    Switch off the A/C.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the cooling fan.

  1. Stop the engine, and wait until the engine coolant cools down to the ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A168578
    Check that the coolant level is between the F and L lines. If the coolant level is below the L line, repeat all of the procedures above. If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.


21. INSPECT FOR COOLANT LEAK (w/o Air Cooled Transmission Oil Cooler)

  1. A168576
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.


22. ADD AUTOMATIC TRANSMISSION FLUID
(Click here)

23. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that it moves smoothly and correctly into position.

  1. Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.
    If there are no problems during the above inspections, perform the adjustment using the following procedures.

    1. Move the shift lever to N

    2. C172428E01
      Loosen the nut of the floor shift gear shifting rod. Then, with the lever of the floor shift assembly lightly pushed towards the rear of the vehicle, tighten the nut.

      Torque:
      13 N*m{ 130 kgf*cm , 9 ft.*lbf }


24. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

25. INSTALL NO. 1 ENGINE UNDER COVER

C173929
  1. Install the under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


26. INSTALL NO. 2 ENGINE UNDER COVER

C173930
  1. Install the under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


27. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


28. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


29. RESET MEMORY
  1. Perform the Reset Memory procedures (A/T initialization) (Click here).

← REMOVAL (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →