2011-2013 Land Cruiser · Service Manual Suspension

C1718 Pressure Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit is used for sending the data to detect the pressure output from the pump. The abnormality of the fluid pressure is judged by the ECU.
DTC Code
Detecting Condition
Trouble Area
C1718
When one of the following conditions is met:
  1. When detecting an abnormal signal from the pressure sensor (pressure sensor terminal voltage of ECU is 0.3 V or less or 4.6 V or more) for 1 second.
  2. When there is a pressure sensor power supply voltage malfunction.
  3. When a pressure of 1 MPa (10.2 kgf/cm2, 145 psi) or more is placed on the pressure sensor for 20 seconds or more, no voltage is flowing to the height control pump and motor, and the vehicle height control is not operating, it is determined that there is a sensor stuck malfunction.
  1. Harness or connector
  2. Height control pump and motor (Pressure sensor)
  3. Suspension control ECU

WIRING DIAGRAM

C176909E01

INSPECTION PROCEDURE

NOTICE:
  1. Before performing troubleshooting, inspect the connectors of related circuits.
  2. If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).


1. CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - SUSPENSION CONTROL ECU)

NOTICE:
When inspecting the wire harness between the suspension control ECU and pressure sensor, it is difficult to determine the malfunctioning area if there is a sensor power supply malfunction. Therefore, disconnect the connectors for the pressure sensor, the acceleration sensors (front RH, front LH) and fluid temperature sensor on the ECU side.

  1. Disconnect the i2 pressure sensor connector.

  1. Disconnect the K34 and K35 ECU connectors.C174707E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K35-10 (SPB) - i2-1 (SHB)
    Always
    Below 1 Ω
    K35-19 (SPG) - i2-3 (SHG)
    Always
    Below 1 Ω
    K35-20 (PACC) - i2-2 (PACC)
    Always
    Below 1 Ω
    K35-10 (SPB) - Body ground
    Always
    10 kΩ or higher
    K35-19 (SPG) - Body ground
    Always
    10 kΩ or higher
    K35-20 (PACC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK SUSPENSION CONTROL ECU
C174710E01
  1. Connect the K34 and K35 suspension control ECU connectors.

  1. Disconnect the i2 pressure sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    i2-1 (SHB) - i2-3 (SHG)
    Engine switch on (IG)
    4.75 to 5.25 V



NG
REPLACE SUSPENSION CONTROL ECU (Click here)
OK


3. CHECK PRESSURE SENSOR
  1. Connect the K34 and K35 suspension control ECU connectors.

  1. Connect the i2 pressure sensor connector.

  1. C174711E01
    Start the engine and push the up button of the height control switch to activate height control.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K35-20 (PACC) - K35-19 (SPG)
    While height control is operating.
    1.48 to 2.54 V



NG
REPLACE HEIGHT CONTROL PUMP AND MOTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1718 Pressure Sensor Circuit Malfunction (Sep 2011 – Dec 2011)C1719 Oil Temperature Sensor Circuit Malfunction (Sep 2011 – Dec 2011) →