2011-2013 Land Cruiser · Service Manual Suspension

C1731 Front Damping Force Control Actuator RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The ECU sends a signal to the damping force control actuator to drive the rotary valve of the shock absorber changing the shock absorber damping force.
The actuator is driven electromagnetically by a step motor so that it can accurately follow the driving conditions that change frequently.
DTC Code
Detection Condition
Trouble Area
C1731
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Front shock absorber control valve RH (Front damping force control actuator RH)
  3. Suspension control ECU
C1732
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Front shock absorber control valve LH (Front damping force control actuator LH)
  3. Suspension control ECU
C1733
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Rear shock absorber control valve RH (Rear damping force control actuator RH)
  3. Suspension control ECU
C1734
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Harness or connector
  2. Rear shock absorber control valve LH (Rear damping force control actuator LH)
  3. Suspension control ECU

WIRING DIAGRAM

C177526E02

INSPECTION PROCEDURE

NOTICE:
  1. Before performing troubleshooting, inspect the connectors of related circuits.
  2. If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DAMPER STEP)
  1. According to the display on the intelligent tester, perform the Active Test.

  1. Check if the damping force control actuator operates in accordance with the Active Test.

    AHC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Damper Step FR
    Changes front damper RH step
    min.: 1 step
    max.: 16 step
    The Damper Step item of the Data List changes to the step selected in the Active Test.
    Damper Step FL
    Changes front damper LH step
    min.: 1 step
    max.: 16 step
    The Damper Step item of the Data List changes to the step selected in the Active Test.
    Damper Step RR
    Changes rear damper RH step
    min.: 1 step
    max.: 16 step
    The Damper Step item of the Data List changes to the step selected in the Active Test.
    Damper Step RL
    Changes rear damper LH step
    min.: 1 step
    max.: 16 step
    The Damper Step item of the Data List changes to the step selected in the Active Test.

    OK:
    The damping force control actuator operates.



NG
Go to step 3
OK


2. RECONFIRM DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (DAMPING FORCE CONTROL ACTUATOR - SUSPENSION CONTROL ECU)

  1. Check the front side damping force control actuator.

    1. Disconnect the N9 and/or N11 actuator connector.

    2. Disconnect the K36 ECU connector.C174820E01

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for RH (C1731) 
      Tester Connection
      Condition
      Specified Condition
      K36-5 (FAR-) - N9-4 (FAR-)
      Always
      Below 1 Ω
      K36-5 (FAR-) - Body ground
      Always
      10 kΩ or higher
      K36-6 (FAR+) - N9-1 (FAR+)
      Always
      Below 1 Ω
      K36-6 (FAR+) - Body ground
      Always
      10 kΩ or higher
      K36-17 (FBR-) - N9-3 (FBR-)
      Always
      Below 1 Ω
      K36-17 (FBR-) - Body ground
      Always
      10 kΩ or higher
      K36-18 (FBR+) - N9-5 (FBR+)
      Always
      Below 1 Ω
      K36-18 (FBR+) - Body ground
      Always
      10 kΩ or higher
      N9-2 (E FR) - Body ground
      Always
      Below 1 Ω
      for LH (C1732) 
      Tester Connection
      Condition
      Specified Condition
      K36-2 (FBL+) - N11-5 (FBL+)
      Always
      Below 1 Ω
      K36-2 (FBL+) - Body ground
      Always
      10 kΩ or higher
      K36-3 (FAL-) - N11-4 (FAL-)
      Always
      Below 1 Ω
      K36-3 (FAL-) - Body ground
      Always
      10 kΩ or higher
      K36-4 (FAL+) - N11-1 (FAL+)
      Always
      Below 1 Ω
      K36-4 (FAL+) - Body ground
      Always
      10 kΩ or higher
      K36-12 (FBL-) - N11-3 (FBL-)
      Always
      Below 1 Ω
      K36-12 (FBL-) - Body ground
      Always
      10 kΩ or higher
      N11-2 (E FL) - Body ground
      Always
      Below 1 Ω

  1. Check the rear side damping force control actuator.

    1. Disconnect the N6 and/or N8 actuator connector.

    2. Disconnect the K35 ECU connector.C174821E01

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for RH (C1733) 
      Tester Connection
      Condition
      Specified Condition
      K35-4 (RBR-) - N6-3 (RBR-)
      Always
      Below 1 Ω
      K35-4 (RBR-) - Body ground
      Always
      10 kΩ or higher
      K35-5 (RAR+) - N6-1 (RAR+)
      Always
      Below 1 Ω
      K35-5 (RAR+) - Body ground
      Always
      10 kΩ or higher
      K35-13 (RBR+) - N6-5 (RBR+)
      Always
      Below 1 Ω
      K35-13 (RBR+) - Body ground
      Always
      10 kΩ or higher
      K35-14 (RAR-) - N6-4 (RAR-)
      Always
      Below 1 Ω
      K35-14 (RAR-) - Body ground
      Always
      10 kΩ or higher
      N6-2 (E RR) - Body ground
      Always
      Below 1 Ω
      for LH (C1734) 
      Tester Connection
      Condition
      Specified Condition
      K35-2 (RAL-) - N8-4 (RAL-)
      Always
      Below 1 Ω
      K35-2 (RAL-) - Body ground
      Always
      10 kΩ or higher
      K35-3 (RAL+) - N8-1 (RAL+)
      Always
      Below 1 Ω
      K35-3 (RAL+) - Body ground
      Always
      10 kΩ or higher
      K35-7 (RBL-) - N8-3 (RBL-)
      Always
      Below 1 Ω
      K35-7 (RBL-) - Body ground
      Always
      10 kΩ or higher
      K35-8 (RBL+) - N8-5 (RBL+)
      Always
      Below 1 Ω
      K35-8 (RBL+) - Body ground
      Always
      10 kΩ or higher
      N8-2 (E RL) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT DAMPING FORCE CONTROL ACTUATOR

  1. Check the front side damping force control actuator.

    1. Connect the N9 and/or N11 front absorber control actuator connector.

    2. C174826E01
      Disconnect the K36 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for RH (C1731) 
      Tester Connection
      Condition
      Specified Condition
      K36-5 (FAR-) - Body ground
      Always
      12.0 to 13.6 Ω
      K36-6 (FAR+) - Body ground
      Always
      12.0 to 13.6 Ω
      K36-17 (FBR-) - Body ground
      Always
      12.0 to 13.6 Ω
      K36-18 (FBR+) - Body ground
      Always
      12.0 to 13.6 Ω
      for LH (C1732) 
      Tester Connection
      Condition
      Specified Condition
      K36-2 (FBL+) - Body ground
      Always
      12.0 to 13.6 Ω
      K36-3 (FAL-) - Body ground
      Always
      12.0 to 13.6 Ω
      K36-4 (FAL+) - Body ground
      Always
      12.0 to 13.6 Ω
      K36-12 (FBL-) - Body ground
      Always
      12.0 to 13.6 Ω

  1. Check the rear side damping force control actuator.

    1. Connect the N6 and/or N8 rear absorber control actuator connector.

    2. C174827E01
      Disconnect the K35 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for RH (C1733) 
      Tester Connection
      Condition
      Specified Condition
      K35-4 (RBR-) - Body ground
      Always
      12.0 to 13.6 Ω
      K35-5 (RAR+) - Body ground
      Always
      12.0 to 13.6 Ω
      K35-13 (RBR+) - Body ground
      Always
      12.0 to 13.6 Ω
      K35-14 (RAR-) - Body ground
      Always
      12.0 to 13.6 Ω
      for LH (C1734) 
      Tester Connection
      Condition
      Specified Condition
      K35-2 (RAL-) - Body ground
      Always
      12.0 to 13.6 Ω
      K35-3 (RAL+) - Body ground
      Always
      12.0 to 13.6 Ω
      K35-7 (RBL-) - Body ground
      Always
      12.0 to 13.6 Ω
      K35-8 (RBL+) - Body ground
      Always
      12.0 to 13.6 Ω

Result 
Result
Proceed to
OK
A
Front damping force control actuator RH malfunction
B
Front damping force control actuator LH malfunction
C
Rear damping force control actuator RH malfunction
D
Rear damping force control actuator LH malfunction
E


B
REPLACE FRONT SHOCK ABSORBER CONTROL VALVE RH (Click here)

C
REPLACE FRONT SHOCK ABSORBER CONTROL VALVE LH (Click here)

D
REPLACE REAR SHOCK ABSORBER CONTROL VALVE RH (Click here)

E
REPLACE REAR SHOCK ABSORBER CONTROL VALVE LH (Click here)
A

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1719 Oil Temperature Sensor Circuit Malfunction (from Jan 2012)C1731 Front Damping Force Control Actuator RH Circuit Malfunction (+ C1732, C1733, C1734) (from Jan 2012) →