2011-2013 Land Cruiser · Service Manual Brake

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If any of the following is detected, the ABS warning light remains on.
  1. The skid control ECU connectors are disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and skid control ECU.

HINT:
There is a case that the intelligent tester cannot be used when the skid control ECU is abnormal.


WIRING DIAGRAM

C173343E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check the skid control ECU connector connection.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG
    for 2UZ-FE
    B
    for 1VD-FTV
    C
    for 3UR-FE
    D



B
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

C
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

D
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)
A


3. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

    Result 
    Result
    Proceed to
    "Bus Check" indicates no malfunctions in CAN communication
    A
    "Bus Check" indicates no malfunctions in CAN communication
    for LHD
    B
    for RHD
    C

    OK:
    "Bus Check" indicates no malfunctions in CAN communication.



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


4. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Check for DTCs (LHD: Click here/RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output
    A
    CAN system DTC is output
    for LHD
    B
    for RHD
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


5. CHECK OPERATION OF ABS WARNING LIGHT (ACTIVE TEST)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the condition of the ABS warning light by operating the intelligent tester.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp ABS
    ABS Warning Light
    Warning light ON/OFF
    -

    OK:
    The warning light turns on when operating the intelligent tester.

    Result 
    Result
    Proceed to
    OK
    A
    NG
    w/ Multi-information Display
    B
    w/o Multi-information Display
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


6. INSPECT SKID CONTROL ECU (IG1 TERMINAL)

  1. C173351E16
    Disconnect the A24 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT SKID CONTROL ECU (GND TERMINAL)

  1. C124799E43
    Disconnect the A24 and A25 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A24-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A25-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK
    for LHD
    B
    for RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← U0073/94 Control Module Communication Bus OFF (+ 6 more codes) (Sep 2011 – Dec 2011)ABS Warning Light Remains ON (from Jan 2012) →