C1253/53 Pump Motor Relay Malfunction
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
DESCRIPTION
The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1253/53 |
There is a motor system circuit (motor input circuit) malfunction. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the hydraulic brake booster assembly (master cylinder solenoid), perform zero point calibration (Click here).
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Motor Relay
Motor relay
Relay ON/OFF
An operation sound of the motor can be heard.
Check the operation sound of the motor individually when operating it with the intelligent tester.
- OK:
- The operation sound of the motor can be heard.
|
|
||||
| OK | |
| 2. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Depress the brake pedal more than 20 times.
Turn the ignition switch to ON.
Wait until the pump motor stops.
Depress the brake pedal several times until the pump motor turns on. (Procedure A)
Wait until the pump stops. (Procedure B)
Repeat the above steps (procedure A and B) 3 more times.
Check if the same DTC is output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is not output
A
DTC is output
LHD
B
RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. INSPECT SKID CONTROL ECU (+BM TERMINAL) |
Disconnect the A24 and A25 skid control ECU connectors.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A24-2 (+BM1) - Body ground
Always
11 to 14 V
A25-2 (+BM2) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 4. INSPECT SKID CONTROL ECU (GND TERMINAL) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
A24-1 (GND1) - Body ground
Always
Below 1 Ω
A24-32 (GND2) - Body ground
Always
Below 1 Ω
A25-4 (GND3) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Depress the brake pedal more than 20 times.
Turn the ignition switch to ON.
Wait until the pump motor stops.
Depress the brake pedal several times until the pump motor turns on. (Procedure A)
Wait until the pump stops. (Procedure B)
Repeat the above steps (procedure A and B) 3 more times.
Check if the same DTC is output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is not output
A
DTC is output
LHD
B
RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
