2011-2013 Land Cruiser · Service Manual Brake

C0278/11 Open or Short Circuit in ABS Solenoid Relay Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The solenoid relay is built into the master cylinder solenoid.
This relay supplies power to each solenoid. If the initial check is OK, after the ignition switch is turned to ON, the relay turns on.
DTC Code
DTC Detection Condition
Trouble Area
C0278/11
When either of the following conditions is detected:
  1. Both of the following conditions continue for at least 0.2 seconds.
    1. IG voltage is between 9.5 V and 17 V.
    2. The relay contact is open when the relay is on.
  2. Both of the following conditions continue for at least 0.2 seconds.
    1. IG voltage is 9.5 V or less when the relay is on.
    2. The relay contact remains open.
  1. ABS2 fuse
  2. Solenoid relay
  3. Harness or connector
  4. Master cylinder solenoid (Skid control ECU)
C0279/12
The following condition continues for at least 0.2 seconds.
  1. The relay contact is closed immediately after turning the ignition switch to ON when the relay is off.
  1. ABS2 fuse
  2. Solenoid relay
  3. Harness or connector
  4. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

C173275E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. INSPECT ABS2 FUSE

  1. C176463E01
    Remove the ABS2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ABS2 fuse
    Always
    Below 1 Ω



NG
REPLACE ABS2 FUSE
OK


2. INSPECT SKID CONTROL ECU (+BS TERMINAL)

  1. C173351E09
    Install the ABS2 fuse.

  1. Disconnect the A24 skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-31 (+BS) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT SKID CONTROL ECU (GND TERMINAL)

  1. C124799E41
    Disconnect the A24 and A25 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A24-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A25-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. RECONFIRM DTC

HINT:
These codes are stored when a problem is detected in the master cylinder solenoid.
The ABS solenoid relay is in the master cylinder solenoid.
Therefore, solenoid relay circuit inspection and relay unit inspection cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    LHD
    B
    RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C0226/21 SFR Solenoid Circuit (+ 7 more codes) (Sep 2011 – Dec 2011)C1202/58 Brake Fluid Level Low / Open Circuit in Brake Fluid Level Warning Switch Circuit (Sep 2011 – Dec 2011) →