2011-2013 Land Cruiser · Service Manual Brake

C1241/41 Low Battery Positive Voltage

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

If the voltage supplied to the IG1 terminal is within the DTC detection range due to malfunctions in components such as the battery and alternator circuit, this DTC is stored.
DTC Code
DTC Detection Condition
Trouble Area
C1241/41
When either of the following conditions is detected:
1. Both of the following conditions continue for at least 10 seconds.
  1. The vehicle speed is more than 3 km/h (2 mph).
  2. The IG1 terminal voltage is below 9.5 V.
2. All of the following conditions continue for at least 0.2 seconds.
  1. The solenoid relay remains on.
  2. The IG1 terminal voltage is below 9.5 V.
  3. The relay contact is open.
  1. Battery
  2. ECU-IG No. 2 fuse
  3. Charging system
  4. Harness or connector
  5. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

C173289E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result
    Proceed to
    OK
    A
    NG
    for 2UZ-FE
    B
    for 1VD-FTV
    C
    for 3UR-FE
    D



B
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

C
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

D
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)
A


2. INSPECT ECU-IG NO. 2 FUSE

  1. C178955E01
    Remove the ECU-IG No. 2 fuse from the main body ECU (cowl side junction block LH).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 2 fuse
    Always
    Below 1 Ω



NG
REPLACE ECU-IG NO. 2 FUSE
OK


3. READ VALUE USING INTELLIGENT TESTER (IG1 VOLTAGE VALUE)
  1. Install the ECU-IG No. 2 fuse.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG1 Voltage Value
    IG1 voltage value/min.: 0.00 V, max.: 20.00 V
    9.5 to 14 V
    -

  1. Measure the voltage output from the skid control ECU displayed on the intelligent tester.

    OK:
    The output voltage displayed on the intelligent tester is within 9.5 to 14.0 V.



NG
Go to step 5
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    for LHD
    A
    for RHD
    B
    DTC is not output (When troubleshooting in accordance with the Diagnostic Trouble Code Chart)
    C
    DTC is not output (When troubleshooting in accordance with the Problem Symptoms Table)
    D



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)

D
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

5. INSPECT SKID CONTROL ECU (IG1 TERMINAL)

  1. C173351E10
    Disconnect the A24 skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT SKID CONTROL ECU (GND TERMINAL)

  1. C124799E41
    Disconnect the A24 and A25 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A24-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A25-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    for LHD
    A
    for RHD
    B
    DTC is not output (When troubleshooting in accordance with the Diagnostic Trouble Code Chart)
    C
    DTC is not output (When troubleshooting in accordance with the Problem Symptoms Table)
    D



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)

D
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1241 Low Power Supply Voltage Malfunction (from Jan 2012)C1242 Open Circuit in IG1/IG2 Power Source Circuit (from Jan 2012) →