2011-2013 Land Cruiser · Service Manual Brake

C1254/54 Pressure Switch Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The accumulator pressure sensor is connected to the skid control ECU in the master cylinder solenoid.
C173281E01
DTC Code
DTC Detection Condition
Trouble Area
C1254/54
There is an accumulator pressure sensor malfunction (the fluid pressure does not change when the pump operates or when the brake is applied).
  1. Hydraulic brake booster
  2. Accumulator pressure sensor
  3. Master cylinder pressure sensor

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor reading / min.: 0.00 V, max.: 5.00 V
    3.58 to 5 V
    If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.

  1. Check the accumulator output value.

    Result 
    Result
    Proceed to
    Output value is within the "Normal Condition" range
    A
    Output value is out of the "Normal Condition" range
    LHD
    B
    Output value is constant regardless of pump operation
    LHD
    Output value is out of the "Normal Condition" range
    RHD
    C
    Output value is constant regardless of pump operation
    RHD



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER SENSOR)
  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Install the brake pedal effort gauge (SST), and bleed air.

SST
09709-29018  
  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Master Cylinder Sensor
    Master cylinder pressure sensor reading / min.: 0.00 V, max.: 5.00 V
    0.3 to 1.8 V
    With pedal effort of 49 N (5 kgf, 11 in.*lbf)
    The front brake pressure is 930 to 2130 kPa (9.5 to 21.7 kgf/cm2, 135 to 309 psi).

  1. Check that the master cylinder pressure sensor output value is normal.

    OK:
    Master cylinder pressure sensor value is normal.

    Result 
    Result
    Proceed to
    OK
    A
    NG
    LHD
    B
    RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A


3. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to ON.

  1. Wait until the pump motor stops.

  1. Depress the brake pedal and release it.

  1. Wait for 25 minutes.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    LHD
    B
    RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1254 Pressure Sensor or Switch (from Jan 2012)C1256 Accumulator Low Pressure (from Jan 2012) →