2011-2013 Land Cruiser · Service Manual Brake

VSC OFF Indicator Light Remains ON

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the center differential is locked or the VSC OFF switch is operated, VSC control turns off and the VSC OFF indicator illuminates.

WIRING DIAGRAM

C173346E03

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. CHECK DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2. INSPECT IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check the skid control ECU connector connection.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG
    for 2UZ-FE
    B
    for 1VD-FTV
    C
    for 3UR-FE
    D



B
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

C
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

D
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)
A


4. INSPECT SKID CONTROL ECU (EXI TERMINAL)

  1. C173351E12
    Disconnect the A24 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-27 (EXI) - Body ground
    Center differential free
    (Center differential lock switch off)
    (Center differential lock detection switch off)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

    Result 
    Result
    Proceed to
    "Bus Check" indicates no malfunctions in CAN communication
    A
    "Bus Check" indicates malfunctions in CAN communication
    for LHD
    B
    for RHD
    C

    OK:
    "Bus Check" indicates no malfunctions in CAN communication.



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


6. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Check for DTCs (LHD: Click here/RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output
    A
    CAN system DTC is output
    for LHD
    B
    for RHD
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


7. CHECK OPERATION OF VSC OFF INDICATOR (ACTIVE TEST)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the intelligent tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the condition of the VSC OFF indicator by operating the intelligent tester.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp VSC OFF
    VSC OFF Indicator
    Indicator ON/OFF
    -

    OK:
    The indicator turns on/off when operating the intelligent tester.

    Result 
    Result
    Proceed to
    OK
    for LHD
    A
    for RHD
    B
    NG
    w/ Multi-information Display
    C
    w/o Multi-information Display
    D



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)

D
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← TRC OFF Indicator Light does not Come ON (from Jan 2012)VSC OFF Indicator Light Remains ON (from Jan 2012) →