2011-2013 Land Cruiser · Service Manual Power Source / Network

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
  1. "ECM (Engine)" is not displayed on "Bus Check".
  2. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside ECM
  2. ECM main wire or connector
  3. ECM

WIRING DIAGRAM

C158954E16
C158954E09
C176046E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
C177488E04
  1. Disconnect the A38 and C45 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2UZ-FE, 3UR-FE:
    Tester Connection
    Condition
    Specified Condition
    C45-81 (E1) - Body ground
    Always
    Below 1 Ω
    C45-42 (E02) - Body ground
    Always
    Below 1 Ω
    C45-43 (E01) - Body ground
    Always
    Below 1 Ω
    C45-82 (ME01) - Body ground
    Always
    Below 1 Ω
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    C45-81 (E1) - Body ground
    Always
    Below 1 Ω
    C45-22 (E01) - Body ground
    Always
    Below 1 Ω
    C45-21 (E02) - Body ground
    Always
    Below 1 Ω
    C45-20 (ME01) - Body ground
    Always
    Below 1 Ω
    for 1VD-FTV:
    Tester Connection
    Condition
    Specified Condition
    C45-81 (E1) - Body ground
    Always
    Below 1 Ω
    C45-21 (E02) - Body ground
    Always
    Below 1 Ω
    C45-22 (E01) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2UZ-FE, 3UR-FE:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (BATT) - Body ground
    Always
    11 to 14 V
    A38-2 (+B2) - Body ground
    Battery positive (+) voltage applied to terminal A38-34 (MREL)
    11 to 14 V
    A38-3 (+B) - Body ground
    Battery positive (+) voltage applied to terminal A38-34 (MREL)
    11 to 14 V
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    A38-20 (BATT) - Body ground
    Always
    11 to 14 V
    A38-1 (+B2) - Body ground
    Battery positive (+) voltage applied to terminal A38-44 (MREL)
    11 to 14 V
    A38-2 (+B) - Body ground
    Battery positive (+) voltage applied to terminal A38-44 (MREL)
    11 to 14 V
    for 1VD-FTV:
    Tester Connection
    Condition
    Specified Condition
    A38-20 (BATT) - Body ground
    Always
    11 to 14 V
    A38-44 (MREL) - Body ground
    Ignition switch ON
    11 to 14 V
    A38-2 (+B) - Body ground
    Battery positive (+) voltage applied to terminal A38-44 (MREL)
    11 to 14 V

    Result 
    Result
    Proceed to
    OK (for 2UZ-FE)
    A
    OK (for 1GR-FE)
    B
    OK (for 1VD-FTV)
    C
    OK (for 3UR-FE)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← Gateway ECU Communication Stop Mode (from Jan 2012)ECM Communication Stop Mode (from Jan 2012) →