2011-2013 Land Cruiser · Service Manual Power Source / Network

Air Conditioning Amplifier Communication Stop Mode

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Detection Item
Symptom
Trouble Area
Air Conditioning Amplifier Communication Stop Mode
Either condition is met:
  1. "Air Conditioning Amplifier" is not displayed on "Bus Check".
  2. "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside air conditioning amplifier assembly
  2. Air conditioning amplifier assembly
  3. Air conditioning amplifier assembly CAN branch wire or connector

WIRING DIAGRAM

C176045E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicle with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)

  1. E191927E02
    Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.
    1. *1: w/ Rear Air Conditioning System
    2. *2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Air Conditioning System 
    Tester Connection
    Switch Condition
    Specified Condition
    E35-3 (CANH) - E35-4 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o Rear Air Conditioning System 
    Tester Connection
    Switch Condition
    Specified Condition
    E81-11 (CANH) - E81-12 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/ Rear Air Conditioning System
    *B
    w/o Rear Air Conditioning System
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

  1. C261151E01
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E36*1 or E81*2 air conditioning amplifier assembly connector.

    1. *1: w/ Rear Air Conditioning System
    2. *2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Rear Air Conditioning System 
    Tester Connection
    Condition
    Specified Condition
    E36-1 (GND) - Body ground
    Always
    Below 1 Ω
    E36-2 (E1) - Body ground
    Always
    Below 1 Ω
    w/o Rear Air Conditioning System 
    Tester Connection
    Condition
    Specified Condition
    E81-14 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    w/ Rear Air Conditioning System 
    Tester Connection
    Condition
    Specified Condition
    E36-6 (+B1) - Body ground
    Always
    11 to 14 V
    E36-7 (+B2) - Body ground
    Always
    11 to 14 V
    E36-5 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V
    w/o Rear Air Conditioning System 
    Tester Connection
    Condition
    Specified Condition
    E81-21 (+B1) - Body ground
    Always
    11 to 14 V
    E81-1 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*A
w/ Rear Air Conditioning System
*B
w/o Rear Air Conditioning System
*a
Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← Air Conditioning Amplifier Communication Stop Mode (Sep 2011 – Dec 2011)Gateway ECU Communication Stop Mode (Sep 2011 – Dec 2011) →