2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).
A233285E01
DTC No.
DTC Detection Condition
Trouble Area
P0660
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
  1. Voltage of acoustic control induction system terminal of the ECM is low when the actuator is off.
  2. The engine has been started.
  1. Open or short in intake air control valve circuit
  2. Intake air surge tank assembly (intake air control valve assembly)
  3. ECM

WIRING DIAGRAM

A276701E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING GTS (OPERATE VSV FOR ACIS)
A233358E01
  1. Disconnect the vacuum hose from port F on the vacuum switching valve (for ACIS).

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

  1. Operate the VSV for ACIS.

  1. Check the VSV air flow when switching the VSV.

    OK:
    Test Condition
    Specified Condition
    VSV is ON
    Air from port E flows out through port F
    VSV is OFF
    Air from port E flows out through air filter

    Text in Illustration 
    *a
    VSV is ON
    *b
    VSV is OFF
    *c
    Air



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT VACUUM SWITCHING VALVE (FOR ACIS)
  1. Inspect the vacuum switching valve (for ACIS) (Click here).



NG
REPLACE VACUUM SWITCHING VALVE (FOR ACIS) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE VOLTAGE)

  1. A219139E02
    Disconnect the intake air control valve assembly connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C129-1 - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Intake Air Control Valve Assembly)

  1. Reconnect the intake air control valve assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - VACUUM SWITCHING VALVE)
OK


4. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE - ECM)
  1. Disconnect the intake air control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C129-2 - C46-62 (ACIS)
    Always
    Below 1 Ω
    C129-2 or C46-62 (ACIS) - Body ground
    Always
    10 kΩ or higher
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C129-2 - C45-62 (ACIS)
    Always
    Below 1 Ω
    C129-2 or C45-62 (ACIS) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the intake air control valve assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE - ECM)
OK

REPLACE ECM (Click here)


← P0657 Actuator Supply Voltage Circuit / Open (from Jan 2012)P0724 Brake Switch "B" Circuit High (from Jan 2012) →