B2312 Power Window Switch Malfunction
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The power window regulator motor consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch.This DTC is stored when the ECU built into the regulator motor determines that the power window switch is stuck.
- HINT:
- This DTC may be stored for all the windows.
- NOTICE:
- When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
- After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
- Close the power window by fully pulling up the power window switch and holding it in the auto up position.
- Open the power window by fully pushing down the power window switch.
- When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
B2312 is output.
A
LIN communication DTCs are output.
B
No DTCs output.
C
|
|
||||
|
|
||||
| A | |
| 3. INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Remove the multiplex network master switch assembly (Click here).
for LHD:


Text in Illustration *1
Driver Switch
*2
Front Passenger Switch
*3
Rear RH Side Switch
*4
Rear LH Side Switch
*5
Window Lock Switch
*6
Illumination
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Driver Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
8 (U) - 1 (E) - 4 (AUTO)
5 (D) - 6 (B)
Always (ON/OFF)
UP AUTO
Below 1 Ω
8 (U) - 1(E)
5 (D) - 6 (B)
Always (ON/OFF)
UP MANUAL
Below 1 Ω
8 (U) - 5 (D) - 6 (B)
Always (ON/OFF)
OFF
Below 1 Ω
5 (D) - 1 (E)
8 (U) - 6 (B)
Always (ON/OFF)
DOWN MANUAL
Below 1 Ω
4 (AUTO) - 5(D) - 1 (E)
8 (U) - 6 (B)
Always (ON/OFF)
DOWN AUTO
Below 1 Ω
Passenger Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
6 (B) - 16 (U)
1 (E) - 15 (D)
OFF
UP
Below 1 Ω
1 (E) - 16 (U)
1 (E) - 15 (D)
OFF
OFF
Below 1 Ω
1 (E) - 16 (U)
6 (B) - 15 (D)
OFF
DOWN
Below 1 Ω
6 (B) - 16 (U)
ON
UP
Below 1 Ω
16 (U) - 15 (D)
ON
OFF
Below 1 Ω
6 (B) - 15 (D)
ON
DOWN
Below 1 Ω
Rear RH Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
6 (B) - 10 (U)
1 (E) - 18 (D)
OFF
UP
Below 1 Ω
1 (E) - 18 (D)
1 (E) - 10 (U)
OFF
OFF
Below 1 Ω
6 (B) - 18 (D)
1 (E) - 10 (U)
OFF
DOWN
Below 1 Ω
6 (B) - 10 (U)
ON
UP
Below 1 Ω
18 (D) - 10 (U)
ON
OFF
Below 1 Ω
6 (B) - 18 (D)
ON
DOWN
Below 1 Ω
Rear LH Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
6 (B) - 12 (U)
1 (E) - 13 (D)
OFF
UP
Below 1 Ω
1 (E) - 13 (D)
1 (E) - 12 (U)
OFF
OFF
Below 1 Ω
6 (B) - 13 (D)
1 (E) - 12 (U)
OFF
DOWN
Below 1 Ω
6 (B) - 12 (U)
ON
UP
Below 1 Ω
13 (D) - 12 (U)
ON
OFF
Below 1 Ω
6 (B) - 13 (D)
ON
DOWN
Below 1 Ω
Apply battery voltage to the power window regulator master switch and check that the illumination comes on.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 3 (LED+)
Battery negative (-) → Terminal 1 (E)
Illumination comes on
for RHD:


Text in Illustration *1
Driver Switch
*2
Front Passenger Switch
*3
Rear RH Side Switch
*4
Rear LH Side Switch
*5
Window Lock Switch
*6
Illumination
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Driver Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
1 (U) - 9 (E) - 4 (AUTO)
5 (D) - 6 (B)
Always (ON/OFF)
UP AUTO
Below 1 Ω
1 (U) - 9 (E)
5 (D) - 6 (B)
Always (ON/OFF)
UP MANUAL
Below 1 Ω
1 (U) - 5 (D) - 6 (B)
Always (ON/OFF)
OFF
Below 1 Ω
5 (D) - 9 (E)
1 (U) - 6 (B)
Always (ON/OFF)
DOWN MANUAL
Below 1 Ω
4 (AUTO) - 5 (D) - 9 (E)
1 (U) - 6 (B)
Always (ON/OFF)
DOWN AUTO
Below 1 Ω
Passenger Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
6 (B) - 12 (U)
9 (E) - 13 (D)
OFF
UP
Below 1 Ω
9 (E) - 12 (U)
9 (E) - 13 (D)
OFF
OFF
Below 1 Ω
9 (E) - 12 (U)
6 (B) - 13 (D)
OFF
DOWN
Below 1 Ω
6 (B) - 12 (U)
ON
UP
Below 1 Ω
12 (U) - 13 (D)
ON
OFF
Below 1 Ω
6 (B) - 13 (D)
ON
DOWN
Below 1 Ω
Rear RH Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
6 (B) - 16 (U)
9 (E) - 15 (D)
OFF
UP
Below 1 Ω
9 (E) - 15 (D)
9 (E) - 16 (U)
OFF
OFF
Below 1 Ω
6 (B) - 15 (D)
9 (E) - 16 (U)
OFF
DOWN
Below 1 Ω
6 (B) - 16 (U)
ON
UP
Below 1 Ω
15 (D) - 16 (U)
ON
OFF
Below 1 Ω
6 (B) - 15 (D)
ON
DOWN
Below 1 Ω
Rear LH Side Switch Tester Connection
Window Lock Switch Condition
Power Window Switch Condition
Specified Condition
6 (B) - 18 (U)
9 (E) - 10 (D)
OFF
UP
Below 1 Ω
9 (E) - 10 (D)
9 (E) - 18 (U)
OFF
OFF
Below 1 Ω
6 (B) - 10 (D)
9 (E) - 18 (U)
OFF
DOWN
Below 1 Ω
6 (B) - 18 (U)
ON
UP
Below 1 Ω
10 (D) - 18 (U)
ON
OFF
Below 1 Ω
6 (B) - 10 (D)
ON
DOWN
Below 1 Ω
Apply battery voltage to the power window regulator master switch and check that the illumination comes on.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 3 (LED+)
Battery negative (-) → Terminal 9 (E)
Illumination comes on
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE POWER WINDOW REGULATOR MOTOR) |
Use the Data List to check if the power window regulator motor is functioning properly (Click here).
D-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door P/W Auto SW
Driver side power window auto up/down signal / ON or OFF
ON: Driver side power window auto up/down switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Up SW
Driver side power window manual up signal / ON or OFF
ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW
Driver side power window manual down signal / ON or OFF
ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated
-
Result Result
Proceed to
The display does not change according to operation of the multiplex network master switch.
A
The display changes according to operation of the multiplex network master switch (for LHD).
B
The display changes according to operation of the multiplex network master switch (for RHD).
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR AND BODY GROUND) |
- *1: for LHD
- *2: for RHD
Disconnect I31*1 or I26*2 multiplex network master switch assembly connector.
Disconnect I12*1 or I4*2 power window regulator motor assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
I31-8 (U) - I12-10 (UP)
Always
Below 1 Ω
I31-5 (D) - I12-7 (DOWN)
Always
Below 1 Ω
I31-4 (AUTO) - I12-4 (AUTO)
Always
Below 1 Ω
I31-1 (E) - Body ground
Always
Below 1 Ω
I31-8 (U) or I12-10 (UP) - Body ground
Always
10 kΩ or higher
I31-5 (D) or I12-7 (DOWN) - Body ground
Always
10 kΩ or higher
I31-4 (AUTO) or I12-4 (AUTO) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
I26-1 (U) - I4-10 (UP)
Always
Below 1 Ω
I26-5 (D) - I4-7 (DOWN)
Always
Below 1 Ω
I26-4 (AUTO) - I4-4 (AUTO)
Always
Below 1 Ω
I26-9 (E) - Body ground
Always
Below 1 Ω
I26-1 (U) or I4-10 (UP) - Body ground
Always
10 kΩ or higher
I26-5 (D) or I4-7 (DOWN) - Body ground
Always
10 kΩ or higher
I26-4 (AUTO) or I4-4 (AUTO) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
