Rear Air Conditioning Relay Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When the No. 2 air conditioning control assembly (rear blower switch) is set to position LO or higher, the contact of the RR A/C relay is closed, current flows to the rear blower motor, and the rear blower motor operates. The rear blower motor speed can be changed by exchanging the ground and the rear blower resistor circuit with the No. 2 air conditioning control assembly (rear blower switch).WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT FUSE (A/C IG, RR A/C NO.2) |
Remove the A/C IG and RR A/C NO. 2 fuses from the cowl side junction block LH.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A/C IG fuse
Always
Below 1 Ω
RR A/C NO. 2 fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 2. INSPECT RR A/C RELAY |
![]() ![]() |
Remove the RR A/C relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 4
Battery voltage is not applied between terminals 1 and 2
Below 1 Ω
3 - 5
Battery voltage is not applied between terminals 1 and 2
10 kΩ or higher
3 - 4
Battery voltage is applied to terminals 1 and 2
10 kΩ or higher
3 - 5
Battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT REAR BLOWER MOTOR |
![]() ![]() |
Disconnect the z49 motor connector.
Connect the battery's positive (+) lead to terminal 2 and the negative (-) lead to terminal 1, then check that the rear blower motor operates smoothly.
- OK:
- The rear blower motor operates smoothly.
Measure the current according to the value(s) in the table below.
- Standard Current:
Tester Connection
Condition
Specified Condition
z49-1 (-) - z49-2 (+)
Rear blower motor operates
1 to 3 A
|
|
||||
| OK | |
| 4. INSPECT NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (REAR BLOWER SWITCH) |
![]() ![]() |
Remove the No. 2 air conditioning control assembly (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
ALL - E89-6 (E)
OFF
10 kΩ or higher
E89-5 (LO) - E89-6 (E)
LO
Below 1 Ω
E89-3 (M1) - E89-6 (E)
M1
Below 1 Ω
E89-4 (M2) - E89-6 (E)
M2
Below 1 Ω
E89-8 (HI) - E89-6 (E)
HI
Below 1 Ω
|
|
||||
| OK | |
| 5. INSPECT REAR BLOWER RESISTOR |
![]() ![]() |
Remove the rear blower resistor (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z52-1 (HI) - z52-2 (M1)
Always
1.32 to 1.52 Ω
z52-1 (HI) - z52-3 (M2)
Always
0.39 to 0.45 Ω
z52-1 (HI) - z52-4 (LO)
Always
2.24 to 2.4 Ω
|
|
||||
| OK | |
| 6. CHECK REAR COOLING UNIT EXPANSION VALVE (OPERATION) |
Replace the rear cooling unit expansion valve (Click here).
- HINT:
- Since the rear cooling unit expansion valve cannot be inspected while it is removed from the vehicle, replace the rear cooling unit expansion valve with a normal one and check that the condition returns to normal.
- OK:
- Same problem does not occur.
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - WIRING AIR CONDITIONING HARNESS) |
![]() ![]() |
Disconnect the wiring air conditioning harness sub-assembly connector.
Disconnect the z52 rear blower resistor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
6 (M1) - z52-2 (M1)
Always
Below 1 Ω
5 (M2) - z52-3 (M2)
Always
Below 1 Ω
4 (HI) - z52-1 (HI)
Always
Below 1 Ω
7 (LO) - z52-4 (LO)
Always
Below 1 Ω
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (REAR BLOWER SWITCH - WIRING AIR CONDITIONING HARNESS) |
![]() ![]() |
Disconnect the E89 No. 2 air conditioning control assembly connector.
Disconnect the Wiring air conditioning harness sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E89-3 (M1) - 6 (M1)
Always
Below 1 Ω
E89-4 (M2) - 5 (M2)
Always
Below 1 Ω
E89-8 (HI) - 4 (HI)
Always
Below 1 Ω
E89-5 (LO) - 7 (LO)
Always
Below 1 Ω
E89-6 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - REAR BLOWER MOTOR) |
![]() ![]() |
Disconnect the z52 rear blower resistor connector.
Disconnect the z49 rear motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z52-1 (HI) - z49-1
Always
Below 1 Ω
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR - BODY GROUND AND BATTERY) |
![]() ![]() |
Disconnect the z49 rear motor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z49-2 - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
z49-2 - Body ground
Engine switch on (IG)
Heater control (blower switch) HI
11 to 14 V
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY AND BODY GROUND) |
![]() ![]() |
Disconnect the E81air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E81-18 (RCRL) - Body ground
Engine switch on (IG)
Heater control (blower switch): OFF
11 to 14 V
E81-18 (RCRL) - Body ground
Engine switch on (IG)
Heater control (blower switch): ON
Below 1 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E81-14 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||









