C1AED Rear Sensor Communication Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1AED |
An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the engine switch is turned on (IG). |
|
- *1: w/ Side Monitor System
- *2: w/o Side Monitor System
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1AED is output (w/ Side Monitor System)
A
DTC C1AED is output (w/o Side Monitor System)
B
DTC C1AED is not output
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - PARKING ASSIST ECU) |
Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.
Disconnect the F76 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O9-1 (BI) - F76-20 (CGB2)
Always
Below 1 Ω
O9-3 (SI) - F76-3 (LIN2)
Always
Below 1 Ω
O9-5 (EI) - F76-4 (CSG2)
Always
Below 1 Ω
O9-1 (BI) - Body ground
Always
10 kΩ or higher
O9-3 (SI) - Body ground
Always
10 kΩ or higher
O9-5 (EI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - NO. 1 ULTRASONIC SENSOR [RRC SENSOR]) |
Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.
Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O9-2 (BO) - O10-1 (BI)
Always
Below 1 Ω
O9-4 (SO) - O10-3 (SI)
Always
Below 1 Ω
O9-6 (EO) - O10-5 (EI)
Always
Below 1 Ω
O9-2 (BO) - Body ground
Always
10 kΩ or higher
O9-4 (SO) - Body ground
Always
10 kΩ or higher
O9-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] - NO. 1 ULTRASONIC SENSOR [RLC SENSOR]) |
Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.
Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O10-2 (BO) - O11-1 (BI)
Always
Below 1 Ω
O10-4 (SO) - O11-3 (SI)
Always
Below 1 Ω
O10-6 (EO) - O11-5 (EI)
Always
Below 1 Ω
O10-2 (BO) - Body ground
Always
10 kΩ or higher
O10-4 (SO) - Body ground
Always
10 kΩ or higher
O10-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] - NO. 1 ULTRASONIC SENSOR [RL SENSOR]) |
Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.
Disconnect the O12 No. 1 ultrasonic sensor (RL sensor) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O11-2 (BO) - O12-1 (BI)
Always
Below 1 Ω
O11-4 (SO) - O12-3 (SI)
Always
Below 1 Ω
O11-6 (EO) - O12-5 (EI)
Always
Below 1 Ω
O11-2 (BO) - Body ground
Always
10 kΩ or higher
O11-4 (SO) - Body ground
Always
10 kΩ or higher
O11-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK PARKING ASSIST ECU |
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F76-4 (CGB2) - Body ground
Engine switch on (IG)
7.2 to 8.8 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F76-20 (CSG2) - Body ground
Always
Below 1 Ω
| *a |
Component with harness connected (Parking Assist ECU) |
|
|
||||
| OK | |
| Go to step 3 |
| 7. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
B
DTC C1AED is not output
C
|
|
||||
|
|
||||
| A | |
| 8. REPLACE NO. 1 ULTRASONIC SENSOR (RR SENSOR) |
Replace the No. 1 ultrasonic sensor (RR sensor) with a normally functioning one (Click here).
| NEXT | |
| 9. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
B
DTC C1AED is not output
C
|
|
||||
|
|
||||
| A | |
| 10. REPLACE NO. 1 ULTRASONIC SENSOR (RL SENSOR) |
Replace the No. 1 ultrasonic sensor (RL sensor) with a normally functioning one (Click here).
| NEXT | |
| 11. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
B
DTC C1AED is not output
C
|
|
||||
|
|
||||
| A | |
| 12. REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR) |
Replace the No. 1 ultrasonic sensor (RRC sensor) with a normally functioning one (Click here).
| NEXT | |
| 13. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC C1AED is not output
|
|
||||
| OK | ||
| ||
| 14. REPLACE NO. 1 ULTRASONIC SENSOR (RLC SENSOR) |
Replace the No. 1 ultrasonic sensor (RLC sensor) with a normally functioning one (Click here).
| NEXT | |
| 15. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC C1AED is not output
|
|
||||
| OK | ||
| ||
| 16. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - CLEARANCE WARNING ECU ASSEMBLY) |
Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.
Disconnect the F12 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O9-1 (BI) - F12-7 (CGB2)
Always
Below 1 Ω
O9-3 (SI) - F12-24 (LIN2)
Always
Below 1 Ω
O9-5 (EI) - F12-18 (CSG2)
Always
Below 1 Ω
O9-1 (BI) - Body ground
Always
10 kΩ or higher
O9-3 (SI) - Body ground
Always
10 kΩ or higher
O9-5 (EI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 17. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RR SENSOR] - NO. 1 ULTRASONIC SENSOR [RRC SENSOR]) |
Disconnect the O9 No. 1 ultrasonic sensor (RR sensor) connector.
Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O9-2 (BO) - O10-1 (BI)
Always
Below 1 Ω
O9-4 (SO) - O10-3 (SI)
Always
Below 1 Ω
O9-6 (EO) - O10-5 (EI)
Always
Below 1 Ω
O9-2 (BO) - Body ground
Always
10 kΩ or higher
O9-4 (SO) - Body ground
Always
10 kΩ or higher
O9-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 18. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RRC SENSOR] - NO. 1 ULTRASONIC SENSOR [RLC SENSOR]) |
Disconnect the O10 No. 1 ultrasonic sensor (RRC sensor) connector.
Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O10-2 (BO) - O11-1 (BI)
Always
Below 1 Ω
O10-4 (SO) - O11-3 (SI)
Always
Below 1 Ω
O10-6 (EO) - O11-5 (EI)
Always
Below 1 Ω
O10-2 (BO) - Body ground
Always
10 kΩ or higher
O10-4 (SO) - Body ground
Always
10 kΩ or higher
O10-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 19. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [RLC SENSOR] - NO. 1 ULTRASONIC SENSOR [RL SENSOR]) |
Disconnect the O11 No. 1 ultrasonic sensor (RLC sensor) connector.
Disconnect the O12 No. 1 ultrasonic sensor (RL sensor) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
O11-2 (BO) - O12-1 (BI)
Always
Below 1 Ω
O11-4 (SO) - O12-3 (SI)
Always
Below 1 Ω
O11-6 (EO) - O12-5 (EI)
Always
Below 1 Ω
O11-2 (BO) - Body ground
Always
10 kΩ or higher
O11-4 (SO) - Body ground
Always
10 kΩ or higher
O11-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 20. CHECK CLEARANCE WARNING ECU ASSEMBLY |
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F12-7 (CGB2) - Body ground
Engine switch on (IG)
7.2 to 8.8 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F12-18 (CSG2) - Body ground
Always
Below 1 Ω
| *a |
Component with harness connected (Clearance Warning ECU Assembly) |
|
|
||||
| OK | |
| 21. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
B
DTC C1AED is not output
C
|
|
||||
|
|
||||
| A | |
| 22. REPLACE NO. 1 ULTRASONIC SENSOR (RR SENSOR) |
Replace the No. 1 ultrasonic sensor (RR sensor) with a normally functioning one (Click here).
| NEXT | |
| 23. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
B
DTC C1AED is not output
C
|
|
||||
|
|
||||
| A | |
| 24. REPLACE NO. 1 ULTRASONIC SENSOR (RL SENSOR) |
Replace the No. 1 ultrasonic sensor (RL sensor) with a normally functioning one (Click here).
| NEXT | |
| 25. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
B
DTC C1AED is not output
C
|
|
||||
|
|
||||
| A | |
| 26. REPLACE NO. 1 ULTRASONIC SENSOR (RRC SENSOR) |
Replace the No. 1 ultrasonic sensor (RRC sensor) with a normally functioning one (Click here).
| NEXT | |
| 27. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC C1AED is not output
|
|
||||
| OK | ||
| ||
| 28. REPLACE NO. 1 ULTRASONIC SENSOR (RLC SENSOR) |
Replace the No. 1 ultrasonic sensor (RLC sensor) with a normally functioning one (Click here).
| NEXT | |
| 29. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC C1AED is not output
|
|
||||
| OK | ||
| ||
