2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

C1AED Rear Sensor Communication Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and the ECU, or when there is a malfunction in a rear sensor.
DTC Code
DTC Detection Condition
Trouble Area
C1AED
An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the engine switch is turned on (IG).
  1. Rear ultrasonic sensor circuit
  2. Parking assist ECU*1
  3. Clearance warning ECU*2

HINT:
*1: w/ Parking Assist Monitor System
*2: w/o Parking Assist Monitor System


WIRING DIAGRAM

B184400E02
B184400E01

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC C1AED is output (w/ Parking Assist Monitor System)
    A
    DTC C1AED is output (w/o Parking Assist Monitor System)
    B
    No DTC is output
    C



B
Go to step 16

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK PARKING ASSIST ECU
E140580E07
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F44-28 (BOR) - Body ground
    Engine switch on (IG)
    7.2 to 8.8 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F44-29 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE PARKING ASSIST ECU (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (NO. 2 ULTRASONIC SENSOR RH - PARKING ASSIST ECU)
B186048E02
  1. Disconnect the O1 sensor connector.

  1. Disconnect the F44 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O1-1 (BI) - F44-28 (BOR)
    Always
    Below 1 Ω
    O1-3 (SI) - F44-30 (SOR)
    Always
    Below 1 Ω
    O1-5 (EI) - F44-29 (E2)
    Always
    Below 1 Ω
    O1-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O1-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O1-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (NO. 3 ULTRASONIC SENSOR RH - NO. 2 ULTRASONIC SENSOR RH)
B144572E21
  1. Disconnect the O1 and O2 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O2-1 (BI) - O1-2 (BO)
    Always
    Below 1 Ω
    O2-3 (SI) - O1-4 (SO)
    Always
    Below 1 Ω
    O2-5 (EI) - O1-6 (EO)
    Always
    Below 1 Ω
    O2-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O2-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O2-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (NO. 3 ULTRASONIC SENSOR LH - NO. 3 ULTRASONIC SENSOR RH)
B144572E22
  1. Disconnect the O2 and O3 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O3-1 (BI) - O2-2 (BO)
    Always
    Below 1 Ω
    O3-3 (SI) - O2-4 (SO)
    Always
    Below 1 Ω
    O3-5 (EI) - O2-6 (EO)
    Always
    Below 1 Ω
    O3-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O3-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O3-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (NO. 2 ULTRASONIC SENSOR LH - NO. 3 ULTRASONIC SENSOR LH)
B144572E23
  1. Disconnect the O3 and O4 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (BI) - O3-2 (BO)
    Always
    Below 1 Ω
    O4-3 (SI) - O3-4 (SO)
    Always
    Below 1 Ω
    O4-5 (EI) - O3-6 (EO)
    Always
    Below 1 Ω
    O4-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O4-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O4-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
B
No DTC is output
C


B
Go to step 12

C
USE SIMULATION METHOD TO CHECK (Click here)
A


8. REPLACE NO. 2 ULTRASONIC SENSOR RH
  1. Replace the No. 2 ultrasonic sensor RH with a normally functioning sensor (Click here).


NEXT


9. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
B
No DTC is output
C


B
Go to step 12

C
END (NO. 2 ULTRASONIC SENSOR RH IS DEFECTIVE)
A


10. REPLACE NO. 2 ULTRASONIC SENSOR LH
  1. Replace the No. 2 ultrasonic sensor LH with a normally functioning sensor (Click here).


NEXT


11. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
B
No DTC is output
C


B
REPLACE PARKING ASSIST ECU (Click here)

C
END (NO. 2 ULTRASONIC SENSOR LH IS DEFECTIVE)
A


12. REPLACE NO. 3 ULTRASONIC SENSOR RH
  1. Replace the No. 3 ultrasonic sensor RH with a normally functioning sensor (Click here).


NEXT


13. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output
A
No DTC is output
B


B
END (NO. 3 ULTRASONIC SENSOR RH IS DEFECTIVE)
A


14. REPLACE NO. 3 ULTRASONIC SENSOR LH
  1. Replace the No. 3 ultrasonic sensor LH with a normally functioning sensor (Click here).


NEXT


15. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output
A
No DTC is output
B


B
END (NO. 3 ULTRASONIC SENSOR LH IS DEFECTIVE)
A

REPLACE PARKING ASSIST ECU (Click here)

16. CHECK CLEARANCE WARNING ECU
B179112E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F12-7 (BOR) - Body ground
    Engine switch on (IG)
    7.2 to 8.8 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F12-18 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE CLEARANCE WARNING ECU (Click here)
OK


17. CHECK HARNESS AND CONNECTOR (NO. 2 ULTRASONIC SENSOR RH - CLEARANCE WARNING ECU)
B144573E15
  1. Disconnect the O1 sensor connector.

  1. Disconnect the F12 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O1-1 (BI) - F12-7 (BOR)
    Always
    Below 1 Ω
    O1-3 (SI) - F12-24 (SOR)
    Always
    Below 1 Ω
    O1-5 (EI) - F12-18 (E2)
    Always
    Below 1 Ω
    O1-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O1-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O1-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18. CHECK HARNESS AND CONNECTOR (NO. 3 ULTRASONIC SENSOR RH - NO. 2 ULTRASONIC SENSOR RH)
B144572E21
  1. Disconnect the O1 and O2 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O2-1 (BI) - O1-2 (BO)
    Always
    Below 1 Ω
    O2-3 (SI) - O1-4 (SO)
    Always
    Below 1 Ω
    O2-5 (EI) - O1-6 (EO)
    Always
    Below 1 Ω
    O2-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O2-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O2-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19. CHECK HARNESS AND CONNECTOR (NO. 3 ULTRASONIC SENSOR LH - NO. 3 ULTRASONIC SENSOR RH)
B144572E22
  1. Disconnect the O2 and O3 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O3-1 (BI) - O2-2 (BO)
    Always
    Below 1 Ω
    O3-3 (SI) - O2-4 (SO)
    Always
    Below 1 Ω
    O3-5 (EI) - O2-6 (EO)
    Always
    Below 1 Ω
    O3-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O3-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O3-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


20. CHECK HARNESS AND CONNECTOR (NO. 2 ULTRASONIC SENSOR LH - NO. 3 ULTRASONIC SENSOR LH)
B144572E23
  1. Disconnect the O3 and O4 sensor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (BI) - O3-2 (BO)
    Always
    Below 1 Ω
    O4-3 (SI) - O3-4 (SO)
    Always
    Below 1 Ω
    O4-5 (EI) - O3-6 (EO)
    Always
    Below 1 Ω
    O4-1 (BI) - Body ground
    Always
    10 kΩ or higher
    O4-3 (SI) - Body ground
    Always
    10 kΩ or higher
    O4-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


21. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
    A
    DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
    B
    No DTC is output
    C



B
Go to step 26

C
USE SIMULATION METHOD TO CHECK (Click here)
A


22. REPLACE NO. 2 ULTRASONIC SENSOR RH
  1. Replace the No. 2 ultrasonic sensor RH with a normally functioning sensor (Click here).


NEXT


23. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
B
No DTC is output
C


B
Go to step 26

C
END (NO. 2 ULTRASONIC SENSOR RH IS DEFECTIVE)
A


24. REPLACE NO. 2 ULTRASONIC SENSOR LH
  1. Replace the No. 2 ultrasonic sensor LH with a normally functioning sensor (Click here).


NEXT


25. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output and multi-information display indicates open circuit (Rear Left and Rear Center)
A
DTC C1AED is output and multi-information display indicates open circuit (Rear Left, Rear Center and Rear Right)
B
No DTC is output
C


B
REPLACE CLEARANCE WARNING ECU (Click here)

C
END (NO. 2 ULTRASONIC SENSOR LH IS DEFECTIVE)
A


26. REPLACE NO. 3 ULTRASONIC SENSOR RH
  1. Replace the No. 3 ultrasonic sensor RH with a normally functioning sensor (Click here).


NEXT


27. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output
A
No DTC is output
B


B
END (NO. 3 ULTRASONIC SENSOR RH IS DEFECTIVE)
A


28. REPLACE NO. 3 ULTRASONIC SENSOR LH
  1. Replace the No. 3 ultrasonic sensor LH with a normally functioning sensor (Click here).


NEXT


29. CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

Result 
Result
Proceed to
DTC C1AED is output
A
No DTC is output
B


B
END (NO. 3 ULTRASONIC SENSOR LH IS DEFECTIVE)
A

REPLACE CLEARANCE WARNING ECU (Click here)


← C1AEC Front Sensor Communication Malfunction (from Jan 2012)C1AED Rear Sensor Communication Malfunction (from Jan 2012) →