2011-2013 Land Cruiser · Service Manual Vehicle Interior

B2075 Passenger Side Seat Belt Buckle Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when there is a malfunction in the front seat inner belt buckle switch circuit for the passenger side.
DTC Code
DTC Detection Condition
Trouble Area
B2075
Malfunction in the front seat inner belt (buckle switch) circuit.
  1. Harness or connector
  2. Front seat inner belt (for passenger side)
  3. Seat belt control ECU

WIRING DIAGRAM

E149043E03

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

OK:
DTC B2075 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK SEAT BELT CONTROL ECU

  1. E149045E03
    Reconnect the E41 seat belt control ECU connector.

  1. Disconnect the c30*1 or c24*2 front seat inner belt connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Use an oscilloscope to check the waveform of the seat belt control ECU between the connector terminals.

    Measurement Condition 
    Tester Connection
    E41-5 (PBK+) - E41-6 (PBK-)
    Tool Setting
    5 V/DIV., 20 ms./DIV.
    Switch Condition
    Ignition switch ON
    Front passenger side seat belt unfastened (Buckle switch off)
    Ignition switch ON
    Front passenger side seat belt fastened (Buckle switch on)

    OK:
    4.5 to 5.5 V

    Result 
    Result
    Proceed to
    OK
    (for LHD)
    A
    OK
    (for RHD)
    B
    NG
    C



B
REPLACE SEAT BELT CONTROL ECU (Click here)

C
Go to step 3
A

REPLACE SEAT BELT CONTROL ECU (Click here)

3. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - SEAT BELT CONTROL ECU)

  1. E149044E03
    Disconnect the c30*1 or c24*2 front seat inner belt connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the E41 seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    c30-2 (+) - E41-5 (PBK+)
    Always
    Below 1 Ω
    c30-1 (E) - E41-6 (PBK-)
    c30-2 (+) or E41-5 (PBK+) - Body ground
    1 MΩ higher
    c30-1 (E) or E41-6 (PBK-) - Body ground
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    c24-2 (+) - E41-5 (PBK+)
    Always
    Below 1 Ω
    c24-1 (E) - E41-6 (PBK-)
    c24-2 (+) or E41-5 (PBK+) - Body ground
    1 MΩ higher
    c24-1 (E) or E41-6 (PBK-) - Body ground

Result 
Result
Proceed to
OK
(for LHD)
A
OK
(for RHD)
B
NG
C


B
REPLACE FRONT SEAT INNER BELT LH (for Passenger Side) (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE FRONT SEAT INNER BELT RH (for Passenger Side) (Click here)


← B2074 Driver Side Seat Belt Buckle Switch Circuit Malfunction (from Jan 2012)B2075 Passenger Side Seat Belt Buckle Switch Circuit Malfunction (from Jan 2012) →