B1920/77 Short in Rear Pretensioner Squib RH Circuit
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- B1921/77 Open in Rear Pretensioner Squib RH Circuit
- B1922/77 Short to GND in Rear Pretensioner Squib RH Circuit
- B1923/77 Short to B+ in Rear Pretensioner Squib RH Circuit
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The rear pretensioner squib RH circuit consists of the center airbag sensor and the rear seat outer belt RH.This circuit instructs the SRS to deploy when deployment conditions are met.
Theses DTCs are stored when a malfunction is detected in the rear pretensioner squib RH circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1920/77 |
When one of the following conditions is met:
|
|
| B1921/77 |
When one of the following conditions is met:
|
|
| B1922/77 |
When one of the following conditions is met:
|
|
| B1923/77 |
When one of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here ).
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- HINT:
- To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).
| 1. CHECK REAR SEAT OUTER BELT RH (REAR PRETENSIONER SQUIB RH) |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the rear seat outer belt RH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the rear seat outer belt RH (rear pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1920, B1921, B1922 or B1923 is not output.
- HINT:
- Codes other than DTC B1920, B1921, B1922 and B1923 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 2. CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the No. 2 floor wire connector (on the rear seat outer belt RH side) is not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK NO. 2 FLOOR WIRE (REAR PRETENSIONER SQUIB RH CIRCUIT) |
Disconnect the connectors from the center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
L14-1 (RR+) - Body ground
Ignition switch ON
Below 1 V
L14-2 (RR-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L14-1 (RR+) - L14-2 (RR-)
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L14-1 (RR+) - L14-2 (RR-)
Always
1 MΩ or higher
L14-1 (RR+) - Body ground
Always
1 MΩ or higher
L14-2 (RR-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR |
Connect the connectors to the rear seat outer belt RH and the center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 90 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1920, B1921, B1922 or B1923 is not output.
- HINT:
- Codes other than DTC B1920, B1921, B1922 and B1923 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
