2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1850/62 Short in Rear Side Squib RH Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The rear side squib RH circuit consists of the center airbag sensor and the rear seat side airbag RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the rear side squib RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1850/62
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the rear side squib RH circuit during the primary check.
  2. A rear side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Rear seat side airbag assembly RH (Rear side squib RH)
  3. Center airbag sensor assembly
B1851/62
When one of the following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the rear side squib RH circuit for 2 seconds.
  2. A rear side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Rear seat side airbag assembly RH (Rear side squib RH)
  3. Center airbag sensor assembly
B1852/62
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the rear side squib RH circuit for 0.5 seconds.
  2. A rear side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Rear seat side airbag assembly RH (Rear side squib RH)
  3. Center airbag sensor assembly
B1853/62
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the rear side squib RH circuit for 0.5 seconds.
  2. A rear side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Rear seat side airbag assembly RH (Rear side squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C178002E40

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).


1. CHECK REAR SEAT SIDE AIRBAG RH (REAR SIDE SQUIB RH)

  1. C146260E18
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the rear seat side airbag RH.

  1. Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the rear seat side airbag RH (rear side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1850, B1851, B1852 or B1853 is not output.

    HINT:
    Codes other than DTC B1850, B1851, B1852 and B1853 may be output at this time, but they are not related to this check.
    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE REAR NO. 1 SEAT ASSEMBLY RH (Click here)

C
Go to step 2
A

REPLACE REAR NO. 1 SEAT ASSEMBLY RH (Click here)

2. CHECK NO. 2 FLOOR WIRE (REAR SIDE SQUIB RH CIRCUIT)

  1. C147155E15
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST (resistance: 2.1 Ω) from connector C.

  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Lz2-1 (SRR+) - Body ground
    Ignition switch ON
    Below 1 V
    Lz2-2 (SRR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Lz2-1 (SRR+) - Lz2-2 (SRR-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Lz2-1 (SRR+) - Lz2-2 (SRR-)
    Always
    1 MΩ or higher
    Lz2-1 (SRR+) - Body ground
    Always
    1 MΩ or higher
    Lz2-2 (SRR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


3. CHECK CENTER AIRBAG SENSOR

  1. C146261E26
    Connect the connectors to the rear seat side airbag RH and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1850, B1851, B1852 or B1853 is not output.

    HINT:
    Codes other than DTC B1850, B1851, B1852 and B1853 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1850/62 Short in Rear Side Squib RH Circuit (+ B1851/62, B1852/62, B1853/62) (Sep 2011 – Dec 2011)B1855/63 Short in Rear Side Squib LH Circuit (+ B1856/63, B1857/63, B1858/63) (Sep 2011 – Dec 2011) →