Steering Wheel does not Heat Up When Heated Steering Wheel Switch is Pressed
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
(Click here)WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- The steering heater unit is built into the steering wheel assembly which cannot be disassembled. Therefore, when the steering heater unit has a malfunction, replace the steering wheel assembly.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. INSPECT STEERING WHEEL ASSEMBLY (THERMISTOR·HEATER·THERMOSTAT) |
Disconnect the B steering wheel controller connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B-1 (TH1) - B-2 (TH2)
10 to 30°C (50 to 86°F)
8.132 to 18.43 kΩ
B-4 (SH1) - B-3 (SH2)
20°C (68°F)
1.89 to 2.25 Ω
Text in Illustration *a
Front view of wire harness connector
(to Steering Wheel Control Assembly)
|
|
||||
| OK | |
| 2. INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
Check the connectors and cables of the spiral with sensor cable sub-assembly.
- OK:
- There are no defects such as scratches, cracks, dents or damage on the connectors or cables.
Disconnect the E107 and z63 spiral with sensor cable sub-assembly connectors.


Disconnect the heated steering wheel controller connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z63-1 (CCU) - E107-1 (BTM)
Always
Below 1 Ω
z63-2 (CCV) - E107-3 (ETM)
Always
Below 1 Ω
z63-3 (CCX) - E107-2 (EHT)
Always
Below 1 Ω
z63-4 (CCW) - E107-4 (BHT)
Always
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Spiral with Sensor Cable Sub-assembly)
-
-
|
|
||||
| OK | |
| 3. CHECK STEERING HEATER SWITCH |
Disconnect the G14 steering heater switch connector.

Measure the voltage according to the value(s) in the table below.
- HINT:
- As the circuit has a diode, perform the measurement in diode test mode, and do not mistake the polarity.
- Standard Voltage:
Tester Connection
(Positive (+) tester probe - Negative (-) tester probe)
Condition
Specified Condition
G14-3 (IG) - G14-7 (+)
Always
Below 1.25 V
G14-6 (IN) - G14-7 (+)
Steering heater switch is pushed
Below 1.25 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G14-3 (IG) - G14-6 (IN)
Steering heater switch is pushed
Below 1 Ω
G14-3 (IG) - G14-6 (IN)
Steering heater switch is not pushed
10 kΩ or higher
| *a |
Component without harness connected (Steering Heater Switch) |
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (STEERING HEATER SWITCH - SPIRAL W/ SENSOR CABLE SUB-ASSEMBLY) |
Disconnect the G14 steering heater switch connector.
Disconnect the E107 spiral with sensor cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G14-7 (+) - E107-1 (BTM)
Always
Below 1 Ω
G14-6 (IN) - E107-3 (ETM)
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (IG CIRCUIT) |
Disconnect the G14 steering heater switch connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G14-3 (IG) - Body ground
Ignition switch ON
11 to 14 V
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (IG CIRCUIT) |
Disconnect the E107 spiral with sensor cable subassembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E107-4 (BHT) - Body ground
Ignition switch ON
11 to 14 V
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY BODY GROUND) |
Disconnect the E107 spiral with sensor cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E107-2 (EHT) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
