2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Headlight Cleaner Motor and Relay Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit provides power to the headlight cleaner control relay.
The headlight cleaner control relay sends the signal from the switch, etc. to the headlight cleaner motor to operate the headlight cleaner system.

WIRING DIAGRAM

E158383E07

INSPECTION PROCEDURE


1. INSPECT FUSE (ECU-IG No.1, H-LP CLR)
  1. Remove the ECU-IG No.1 fuse from the main body ECU.

  1. Remove the H-LP CLR fuse from the engine junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No.1 fuse
    Always
    Below 1 Ω
    H-LP CLR fuse



NG
REPLACE FUSE (ECU-IG No. 1, H-LP CLR)
OK


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEAD LIGHT CLEANER)
  1. Using the intelligent tester, perform the Active Test (Click here).

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Cleaner
    Headlight cleaner operation
    ON / OFF
    -

    HINT:
    for Headlight Cleaner System with Wiper Washer Function
    The headlight cleaner system only operates when the windshield wiper switch assembly (front washer switch) is turned on the first time. After that, the headlight cleaner system cannot be operated with the windshield wiper switch assembly (front washer switch) until the engine switch is turned off and then turned to on (IG).

    OK:
    Headlight cleaner operates.



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)

  1. E139345E06
    Disconnect the headlight cleaner control relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V
    3 (IG) - Body ground
    Engine switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (E) - Body ground
    Engine switch on (IG)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

  1. B172829E02
    Remove the headlight cleaner motor and pump assembly (Click here).

  1. Apply battery voltage to the headlight cleaner motor and check the operation of the headlight cleaner motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    Headlight cleaner motor operation is normal



NG
REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (CLEANER MOTOR - CONTROL RELAY AND BATTERY)

  1. E125074E09
    Disconnect the headlight cleaner motor and pump assembly connector.

  1. Disconnect the headlight cleaner control relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 6 (PB)
    Always
    Below 1 Ω
    2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE HEADLIGHT CLEANER CONTROL RELAY
  1. Temporarily replace the head light cleaner control relay new or normally functioning one (Click here).

  1. Check the headlight cleaner system is operates normally.

    OK:
    Headlight cleaner system is operates normally.

    HINT:
    for Headlight Cleaner System with Wiper Washer Function
    The headlight cleaner system only operates when the windshield wiper switch assembly (front washer switch) is turned on the first time. After that, the headlight cleaner system cannot be operated with the windshield wiper switch assembly (front washer switch) until the engine switch is turned off and then turned to on (IG).



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (HEADLIGHT CLEANER CONTROL RELAY IS DEFECTIVE)


← Headlight Cleaner Motor and Relay Circuit (Sep 2011 – Dec 2011)Washer Motor Circuit (Sep 2011 – Dec 2011) →