2011-2013 Land Cruiser · Service Manual Suspension

C1715 Front Acceleration Sensor RH Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle, and outputs it as a voltage to the suspension control ECU. Up and down G sensors are installed in 3 locations: 1) the suspension control ECU, 2) the driver side instrument panel, and 3) the passenger side instrument panel. Each up and down G sensor independently detects the upward and downward acceleration. During a test mode inspection, the suspension control ECU reads the fluctuations in the signal of each sensor. When the sensor cannot detect +/-1.96 m/s2 for 1 second or more during test mode, DTCs C1796, C1797 and C1798 are stored.
DTC Code
Detection Condition
Trouble Area
C1715
C1796
When either of the following conditions is met:
  1. With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the front acceleration sensor RH is detected for 1 second.
  2. When there is a front acceleration sensor RH power supply voltage malfunction.
  1. Harness or connector
  2. Front acceleration sensor RH
  3. Suspension control ECU
C1716
C1797
When either of the following conditions is met:
  1. With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the front acceleration sensor LH is detected for 1 second.
  2. When there is a front acceleration sensor LH power supply voltage malfunction.
  1. Harness or connector
  2. Front acceleration sensor LH
  3. Suspension control ECU
C1717
C1798
When either of the following conditions is met:
  1. With the engine switch on (IG), a voltage of 4.7 V or higher, or 0.3 V or less at the rear acceleration sensor is detected for 1 second.
  2. When there is a rear acceleration sensor power supply voltage malfunction.
Suspension control ECU (Houses rear acceleration sensor)

WIRING DIAGRAM

C177316E01

INSPECTION PROCEDURE

NOTICE:
  1. Before performing troubleshooting, inspect the connectors of related circuits.
  2. If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).
  3. If DTCs C1717 and C1798 (Rear Acceleration Sensor Malfunction) are stored, replace the suspension control ECU (houses rear acceleration sensor).


1. CHECK ACCELERATION SENSOR (DATA LIST)
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and the tester on.

  1. Enter the following menus: Chassis / AHC / Data List.

  1. According to the display on the tester, read the Data List.

    AHC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    (Up & Down)G Sensor FR
    G (up and down) front acceleration sensor RH reading/
    min.: -1045.29 m/s2
    max.: 1045.26 m/s2
    0 +/-0.98 m/s2 at still condition
    Reading changes when vehicle (FR) is bounced
    (Up & Down)G Sensor FL
    G (up and down) front acceleration sensor LH reading/
    min.: -1045.29 m/s2
    max.: 1045.26 m/s2
    0 +/-0.98 m/s2 at still condition
    Reading changes when vehicle (FL) is bounced
    (Up & Down)G Sensor Rear
    G (up and down) rear acceleration sensor reading/
    min.: -1045.29 m/s2
    max.: 1045.26 m/s2
    0 +/-0.98 m/s2 at still condition
    Reading changes when vehicle (rear) is bounced

    OK:
    Reading changes when vehicle is bounced.



NG
Go to step 3
OK


2. RECONFIRM DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Perform a road test.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (ACCELERATION SENSOR - SUSPENSION CONTROL ECU)

NOTICE:
When inspecting the wire harnesses between the suspension control ECU and acceleration sensors, it is difficult to determine the malfunctioning area if there is a sensor power supply malfunction. Therefore, disconnect the connectors for the acceleration sensors (front RH, front LH), the fluid temperature sensor, and fluid pressure sensor on the ECU side.

  1. Check the front acceleration sensor RH side: (C1715)C174713E02

    1. Disconnect the K34 and K35 ECU connectors.

    2. Disconnect the L35 sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L35-1 (SGFR) - K34-24 (SGFR)
      Always
      Below 1 Ω
      L35-2 (SGG) - K34-14 (SGG1)
      Always
      Below 1 Ω
      L35-3 (SGB) - K34-15 (SGB1)
      Always
      Below 1 Ω
      K34-24 (SGFR) - Body ground
      Always
      10 kΩ or higher
      K34-14 (SGG1) - Body ground
      Always
      10 kΩ or higher
      K34-15 (SGB1) - Body ground
      Always
      10 kΩ or higher

  1. Check the front acceleration sensor LH side: (C1716)

    1. Disconnect the K34 and K35 ECU connectors.

    2. Disconnect the K37 sensor connector.C174713E03

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K37-1 (SGFL) - K34-22 (SGFL)
      Always
      Below 1 Ω
      K37-2 (SGG) - K34-13 (SGG2)
      Always
      Below 1 Ω
      K37-3 (SGB) - K34-23 (SGB2)
      Always
      Below 1 Ω
      K34-22 (SGFL) - Body ground
      Always
      10 kΩ or higher
      K34-13 (SGG2) - Body ground
      Always
      10 kΩ or higher
      K34-23 (SGB2) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT ACCELERATION SENSOR
C177935E01
  1. Turn the engine switch off.

  1. Remove the front acceleration sensor (Click here).

    NOTICE:
    Do not drop the acceleration sensor. If it is dropped, replace it with a new one.

  1. Connect 3 1.5 V dry cell batteries in series.

  1. Connect the positive (+) end of the batteries to terminal 3 (SGB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGG). Then measure the voltage between terminal 1 (SGFR*1, SGFL*2) and terminal 2 (SGG).

    HINT:
    *1: for RH
    *2: for LH

    NOTICE:
    Do not apply a voltage of more than 6 V.

    HINT:
    The voltage may differ according to the amount that the sensor is tilted.


    Standard Voltage:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    1 (SGFR) - 2 (SGG)
    Sensor stationary
    Approx. 2.0 to 2.5 V
    Sensor is tilted
    Change between approx. 0.9 to 2.3 V
    for LH 
    Tester Connection
    Condition
    Specified Condition
    1 (SGFL) - 2 (SGG)
    Sensor stationary
    Approx. 2.0 to 2.5 V
    Sensor is tilted
    Change between approx. 0.9 to 2.3 V



NG
REPLACE ACCELERATION SENSOR (Click here)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1711 Front Height Control Sensor RH Circuit Malfunction (+ C1712, C1713, C1714) (from Jan 2012)C1715 Front Acceleration Sensor RH Malfunction (+ 5 more codes) (from Jan 2012) →