2011-2013 Land Cruiser · Service Manual Power Source / Network

Multi-media Module Receiver Assembly Communication Stop Mode

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

Detection Item
Symptom
Trouble Area
Multi-media Module Receiver Assembly Communication Stop Mode
Either condition is met:
  1. "Display and Navigation (AVN)" is not displayed on the "Bus Check" screen.
  2. "Multi-media Module Receiver Assembly Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside of multi-media module receiver assembly
  2. Multi-media module receiver assembly CAN branch wire or connector
  3. Multi-media module receiver assembly
  1. For vehicles with a navigation system.

WIRING DIAGRAM

C175531E14

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR OPEN IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY CAN BRANCH WIRE)

  1. C250794E10
    Disconnect the F77 multi-media module receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F77-1 (CANH) - F77-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multi-media Module Receiver Assembly)



NG
REPAIR OR REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

  1. C250794E11
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-12 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F77-17 (+B1) - Body ground
    Always
    11 to 14 V
    F77-16 (ACC1) - Body ground
    Ignition switch ACC
    11 to 14 V
    F77-15 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Multi-media Module Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)


← 4WD Control ECU Communication Stop Mode (from Jan 2012)Open in CAN Main Wire (Sep 2011 – Dec 2011) →