2011-2013 Land Cruiser · Service Manual Power Source / Network

Open in CAN Main Wire

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. DLC3 branch wire or connector
  3. No. 1 junction connector
  4. No. 2 junction connector
  5. No. 3 junction connector
  6. No. 6 junction connector*
  7. ECM
  8. Combination meter
  1. *: w/o Network Gateway ECU

WIRING DIAGRAM

C230046E01
C246726E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK DLC3

  1. H102621E82
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    OK
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    133 Ω or higher
    NG
    Text in Illustration 
    *1
    DLC3

    NOTICE:
    When the measured value is 133 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)

  1. E207339E01
    Disconnect the E69 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-1 (CANH) - E69-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER)

  1. E207339E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-4 (CANH) - E69-15 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 10
OK

REPLACE NO. 2 JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

  1. E207339E09
    Disconnect the E72 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E72-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 8
OK


7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. E207339E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-1 (CANH) - E72-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the E72 No. 1 junction connector connector.


NEXT


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 1 JUNCTION CONNECTOR)

  1. E207340E01
    Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2UZ-FE, 3UR-FE:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-10 (CANH) - A38-11 (CANL)
    Ignition switch off
    108 to 132 Ω
    for 1GR-FE, 1VD-FTV:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-41 (CANH) - A38-49 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *A
    for 2UZ-FE, 3UR-FE
    *B
    for 1GR-FE, 1VD-FTV
    *1
    Front view of wire harness connector
    (to ECM)
    Result 
    Result
    Proceed to
    OK (for 2UZ-FE)
    A
    OK (for 1GR-FE)
    B
    OK (for 1VD-FTV)
    C
    OK (for 3UR-FE)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 1 JUNCTION CONNECTOR)
A

REPLACE ECM (Click here)

10. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector connector.


NEXT


11. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    w/ Network Gateway ECU
    A
    w/o Network Gateway ECU
    B



B
Go to step 16
A


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER)

  1. E207339E05
    Disconnect the E75 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 14
OK


13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. E207339E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E75-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR

14. CONNECT CONNECTOR
  1. Reconnect the E75 No. 3 junction connector connector.


NEXT


15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 3 JUNCTION CONNECTOR)

  1. E207341E01
    Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-25 (CANH) - E7-26 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter)
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (COMBINATION METER - NO. 3 JUNCTION CONNECTOR)
A

REPLACE COMBINATION METER (Click here)

16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - COMBINATION METER)

  1. E207339E07
    except Double Swing Out Type:
    1. Disconnect the F21 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F21-2 (CANH) - F21-13 (CANL)
      Ignition switch off
      108 to 132 Ω
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to No. 6 Junction Connector)

  1. E207339E10
    for Double Swing Out Type:
    1. Disconnect the F73 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F73-6 (CANH) - F73-17 (CANL)
      Ignition switch off
      108 to 132 Ω
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to No. 6 Junction Connector)



NG
Go to step 18
OK


17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. E207339E08
    except Double Swing Out Type:
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F21-3 (CANH) - F21-14 (CANL)
      Ignition switch off
      108 to 132 Ω
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to No. 6 Junction Connector)

  1. E207339E11
    for Double Swing Out Type:
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F73-7 (CANH) - F73-18 (CANL)
      Ignition switch off
      108 to 132 Ω
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to No. 6 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 6 JUNCTION CONNECTOR

18. CONNECT CONNECTOR
  1. Reconnect the F21*1 or F73*2 No. 6 junction connector connector.

    1. *1: except Double Swing Out Type
    2. *2: for Double Swing Out Type


NEXT


19. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER)

  1. E207339E05
    Disconnect the E75 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 21
OK


20. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. E207339E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E75-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR

21. CONNECT CONNECTOR
  1. Reconnect the E75 No. 3 junction connector connector.


NEXT


22. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 3 JUNCTION CONNECTOR)

  1. E207341E01
    Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-25 (CANH) - E7-26 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter)
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (COMBINATION METER - NO. 3 JUNCTION CONNECTOR)
A

REPLACE COMBINATION METER (Click here)


← Multi-media Module Receiver Assembly Communication Stop Mode (from Jan 2012)Open in CAN Main Wire (from Jan 2012) →