2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Door Courtesy Switch Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The main body ECU receives a door open/closed signal from each door courtesy light switch.

WIRING DIAGRAM

E234117E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY LIGHT SWITCH)
  1. Operate the intelligent tester according to the display and select "Data List".

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Front door courtesy light switch LH signal / ON or OFF
    ON: Front door courtesy light switch LH on
    OFF: Front door courtesy light switch LH off
    -
    P Door Courtesy SW
    Front door courtesy light switch RH signal / ON or OFF
    ON: Front door courtesy light switch RH on
    OFF: Front door courtesy light switch RH off
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal / ON or OFF
    ON: Rear door courtesy light switch LH on
    OFF: Rear door courtesy light switch LH off
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal / ON or OFF
    ON: Rear door courtesy light switch RH on
    OFF: Rear door courtesy light switch RH off
    -
    Back Door Courtesy SW
    Back door courtesy light switch signal / ON or OFF
    ON: Back door courtesy light switch on
    OFF: Back door courtesy light switch off
    -

    OK:
    Door courtesy light switch on/off



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK DOOR COURTESY LIGHT SWITCH
Result 
Result
Proceed to
Front door courtesy light switch LH does not operate
A
Front door courtesy light switch RH does not operate
B
Rear door courtesy light switch LH does not operate
C
Rear door courtesy light switch RH does not operate
D
Back door courtesy light switch does not operate
E


B
Go to step 5

C
Go to step 7

D
Go to step 9

E
Go to step 11
A


3. INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH

  1. E161899E01
    Remove the front door courtesy light switch LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH LH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)

  1. E159510E07
    Disconnect the K2 switch connector.

  1. for LHD:

    1. Disconnect the E1 ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K2-1 - E1-24 (DCTY)
      Always
      Below 1 Ω
      K2-1 - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the E2 ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K2-1 - E2-21 (PCTY)
      Always
      Below 1 Ω
      K2-1 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH

  1. E161899E02
    Remove the front door courtesy light switch RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH RH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)

  1. E159510E08
    Disconnect the L1 switch connector.

  1. for LHD:

    1. Disconnect the E2 ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-1 - E2-21 (PCTY)
      Always
      Below 1 Ω
      L1-1 - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the E1 ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-1 - E1-24 (DCTY)
      Always
      Below 1 Ω
      L1-1 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

7. INSPECT REAR DOOR COURTESY LIGHT SWITCH LH

  1. E161899E03
    Remove the rear door courtesy light switch LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher



NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH LH (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU)

  1. E146248E02
    Disconnect the 2C ECU connector.

  1. Disconnect the K3 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K3-1 - 2C-2 (LCTY)
    Always
    Below 1 Ω
    K3-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

9. INSPECT REAR DOOR COURTESY LIGHT SWITCH RH

  1. E161899E04
    Remove the rear door courtesy light switch RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Not pushed
    Below 1 Ω
    Pushed
    10 kΩ or higher



NG
REPLACE REAR DOOR COURTESY LIGHT SWITCH RH (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU)

  1. E236034E03
    Disconnect the L2 switch connector.

  1. except Double Swing Out Type:

    1. Disconnect the E2 ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L2-1 - E2-7 (RCTY)
      Always
      Below 1 Ω
      L2-1 - Body ground
      Always
      10 kΩ or higher

  1. for Double Swing Out Type:

    1. Disconnect the E1 ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L2-1 - E1-17 (RCTY)
      Always
      Below 1 Ω
      L2-1 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

11. INSPECT VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    for Double Swing Out Type
    A
    except Double Swing Out Type
    B



B
Go to step 14
A


12. INSPECT BACK DOOR WITH MOTOR LOCK ASSEMBLY

  1. Remove the back door with motor lock assembly (Click here).B292780E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (+) - 1 (E)
    Open
    Below 1 Ω
    Half Latch
    Full Latch
    10 kΩ or higher



NG
REPLACE BACK DOOR WITH MOTOR LOCK ASSEMBLY (Click here)
OK


13. CHECK HARNESS AND CONNECTOR (BACK DOOR WITH MOTOR LOCK - MAIN BODY ECU)

  1. E234118E02
    Disconnect E2 ECU connector.

  1. Disconnect W3 door lock connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W3-2 (+) - E2-25 (BCTY)
    Always
    Below 1 Ω
    W3-1 (E) - Body ground
    W3-2 (+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

14. INSPECT BACK DOOR LOCK ASSEMBLY
  1. Remove the back door lock (Click here).

B183291E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (+) - 1 (ACT-)
    Open
    Below 1 Ω
    Full Latch
    10 kΩ or higher



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


15. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - MAIN BODY ECU)

  1. E157947E02
    Disconnect the E2 ECU connector.

  1. Disconnect the S1 door lock connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-3 (+) - E2-25 (BCTY)
    Always
    Below 1 Ω
    S1-1 (ACT-) - Body ground
    S1-3 (+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Headlight Signal Circuit (from Jan 2012)Door Courtesy Switch Circuit (from Jan 2012) →