Oil Pressure Gauge Malfunction
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The oil pressure sender detects the oil pressure generated when the engine is started. The combination meter determines that the engine is running when the engine speed is 400 rpm or more, and determines that the engine is cranking when the engine speed is 200 rpm or less. The oil pressure receiver gauge detects and indicates the oil pressure applied to the oil pressure sender.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK CAN COMMUNICATION SYSTEM |
Check for DTCs (Click here).
Result Result
Proceed to
CAN communication system DTC is not output
A
CAN communication system (for LHD) DTC is output
B
CAN communication system (for RHD) DTC is output
C
|
|
||||
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OIL PRESSURE SENSOR) |
Operate the intelligent tester according to the display and select Active Test (Click here).
Combination Meter Tester Display
Test Part
Control Range
Diagnostic Note
Oil Pressure Meter Operation
Oil pressure receiver gauge
LOW, 1/4, 1/2, 3/4 or HIGH
Perform the test with the vehicle stopped and engine idling.
- OK:
- Needle indication is normal.
Result Result
Proceed to
OK
A
NG (w/ Multi-information Display)
B
NG (w/o Multi-information Display)
C
|
|
||||
|
|
||||
| A | |
| 3. INSPECT OIL PRESSURE GAUGE ASSEMBLY (OIL PRESSURE SENSOR) |
Check that the needle moves in accordance with the engine speed.

- OK:
- Needle is as shown in illustration when engine is stopped.
Needle moves when engine is running.
Result Result
Proceed to
Oil pressure receiver gauge operates correctly according to engine condition
A
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1GR-FE)
B
Oil pressure receiver gauge does not operate correctly according to engine condition (for 2UZ-FE)
C
Oil pressure receiver gauge does not operate correctly according to engine condition (for 3UR-FE)
D
Oil pressure receiver gauge does not operate correctly according to engine condition (for 1VD-FTV)
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENSOR) |
![]() ![]() ![]() ![]() |
for 2UZ-FE, 3UZ-FE, 1VD-FTV:
Disconnect the E8 meter connector.
Disconnect the D18 gauge connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E8-11 (S) - D18-1 (S)
Always
Below 1 Ω
E8-11 (S) or D18-1 (S) - Body ground
Always
10 kΩ or higher
for 1GR-FE:
Disconnect the E8 meter connector.
Disconnect the C33 gauge connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E8-16 (S) - C33-2 (VOUT)
Always
Below 1 Ω
E8-17 (IG+) - C33-3 (VC)
E8-24 (E) - C33-1 (GND)
E8-16 (S) or C33-2 (VOUT) - Body ground
Always
10 kΩ or higher
E8-17 (IG+) or C33-3 (VC) - Body ground
| Result |
Proceed to |
| NG |
A |
| OK (w/ Multi-information Display) |
B |
| OK (w/o Multi-information Display) |
C |
|
|
||||
|
|
||||
| A | ||
| ||


