2011-2013 Land Cruiser · Service Manual Vehicle Interior

Oil Pressure Gauge Malfunction

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The oil pressure sender detects the oil pressure generated when the engine is started. The combination meter determines that the engine is running when the engine speed is 400 rpm or more, and determines that the engine is cranking when the engine speed is 200 rpm or less. The oil pressure receiver gauge detects and indicates the oil pressure applied to the oil pressure sender.

WIRING DIAGRAM

E158843E03

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    CAN communication system DTC is not output
    A
    CAN communication system (for LHD) DTC is output
    B
    CAN communication system (for RHD) DTC is output
    C



B
Go to CAN COMMUNICATION SYSTEM (Click here)

C
Go to CAN COMMUNICATION SYSTEM (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OIL PRESSURE SENSOR)
  1. Operate the intelligent tester according to the display and select Active Test (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Oil Pressure Meter Operation
    Oil pressure receiver gauge
    LOW, 1/4, 1/2, 3/4 or HIGH
    Perform the test with the vehicle stopped and engine idling.

    OK:
    Needle indication is normal.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Multi-information Display)
    B
    NG (w/o Multi-information Display)
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


3. INSPECT OIL PRESSURE GAUGE ASSEMBLY (OIL PRESSURE SENSOR)

  1. E157228
    Check that the needle moves in accordance with the engine speed.

    OK:
    Needle is as shown in illustration when engine is stopped.
    Needle moves when engine is running.

    Result 
    Result
    Proceed to
    Oil pressure receiver gauge operates correctly according to engine condition
    A
    Oil pressure receiver gauge does not operate correctly according to engine condition (for 1GR-FE)
    B
    Oil pressure receiver gauge does not operate correctly according to engine condition (for 1UR-FE)
    C
    Oil pressure receiver gauge does not operate correctly according to engine condition (for 3UR-FE)
    D
    Oil pressure receiver gauge does not operate correctly according to engine condition (for 1VD-FTV)
    E



B
REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY (Click here)

E
REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY (Click here)
A


4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENSOR)
E157230E03
E214570E01
  1. for 1UR-FE, 3UZ-FE, 1VD-FTV:

    1. Disconnect the E8 meter connector.

    2. Disconnect the D18 gauge connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E8-11 (S) - D18-1 (S)
      Always
      Below 1 Ω
      E8-11 (S) or D18-1 (S) - Body ground
      Always
      10 kΩ or higher

  1. for 1GR-FE:

    1. Disconnect the E8 meter connector.

    2. Disconnect the C33 gauge connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E8-16 (S) - C33-2 (VOUT)
      Always
      Below 1 Ω
      E8-17 (IG+) - C33-3 (VC)
      E8-24 (E) - C33-1 (GND)
      E8-16 (S) or C33-2 (VOUT) - Body ground
      Always
      10 kΩ or higher
      E8-17 (IG+) or C33-3 (VC) - Body ground

Result 
Result
Proceed to
NG
A
OK (w/ Multi-information Display)
B
OK (w/o Multi-information Display)
C


B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Oil Pressure Gauge Malfunction (Sep 2011 – Dec 2011)Voltage Meter Malfunction (from Sep 2011) →