2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011


CLEAN CYLINDER HEAD SUB-ASSEMBLY

  1. A053862E01
    Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.

    NOTICE:
    Be careful not to scratch the cylinder block contact surface.

  1. A053863E01
    Using a wire brush, remove all the carbon from the combustion chambers.

    NOTICE:
    Be careful not to scratch the cylinder block contact surface.

  1. A053864E01
    Using a valve guide bushing brush and solvent, clean all the guide bushes.

  1. A053865E01
    Using a soft brush and solvent, thoroughly clean the cylinder head.


INSPECT CYLINDER HEAD SUB-ASSEMBLY

  1. A107611E04
    Using a precision straightedge and feeler gauge, measure the surfaces contacting the cylinder block and manifolds for warpage.

    Standard Warpage:
    Item
    Specified Condition
    Cylinder block side
    0 to 0.05 mm (0 to 0.00197 in.)
    Intake manifold side
    0 to 0.08 mm (0 to 0.00315 in.)
    Exhaust manifold side
    0 to 0.08 mm (0 to 0.00315 in.)

    Maximum warpage:
    0.10 mm (0.00394 in.)

    1. If the warpage is more than the maximum, replace the cylinder head sub-assembly.

  1. A053866E01
    Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
    If the cylinder head is cracked, replace it.


INSPECT INTAKE VALVE

  1. Clean the valves.

    1. A053867E03
      Using a gasket scraper, chip off any carbon from the valve head.

    2. Using a wire brush, thoroughly clean the valve.

  1. A053806E02
    Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.470 to 5.485 mm (0.215 to 0.216 in.)

  1. Check the valve face angle.

    1. A053834E08
      Grind the valve sufficiently to remove pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Standard valve face angle:
      44.5°

      If the valve face is worn, replace the valve.

  1. A053643E05
    Check the valve head margin thickness.

    Standard margin thickness:
    1.0 mm (0.0394 in.)

    Minimum margin thickness:
    0.5 mm (0.0197 in.)

    If the margin thickness is less than the minimum, replace the valve.

  1. A053642E04
    Check the valve overall length.

    Standard overall length:
    95.05 mm (3.74 in.)

    Minimum overall length:
    94.55 mm (3.72 in.)

    If the overall length is less than the minimum, replace the valve.

  1. A053828E02
    Check the surface of the valve stem tip for wear.
    If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.

    NOTICE:
    Be careful not to grind off more than the minimum length.


INSPECT EXHAUST VALVE

  1. Clean the valves.

    1. A053867E04
      Using a gasket scraper, chip off any carbon from the valve head.

    2. Using a wire brush, thoroughly clean the valve.

  1. A053806E03
    Using a micrometer, measure the diameter of the valve stem.

    Standard valve stem diameter:
    5.465 to 5.480 mm (0.215 to 0.216 in.)

  1. Check the valve face angle.

    1. A053834E08
      Grind the valve sufficiently to remove pits and carbon.

    2. Check that the valve is ground to the correct valve face angle.

      Standard valve face angle:
      44.5°

      If the valve face is worn, replace the valve.

  1. A053643E05
    Check the valve head margin thickness.

    Standard margin thickness:
    1.0 mm (0.0394 in.)

    Minimum margin thickness:
    0.5 mm (0.0197 in.)

    If the margin thickness is less than the minimum, replace the valve.

  1. A053642E04
    Check the valve overall length.

    Standard overall length:
    95.10 mm (3.744 in.)

    Minimum overall length:
    94.60 mm (3.724 in.)

    If the overall length is less than the minimum, replace the valve.

  1. A053828E02
    Check the surface of the valve stem tip for wear.
    If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.

    NOTICE:
    Be careful not to grind off more than the minimum length.


INSPECT INTAKE VALVE GUIDE BUSH

  1. A123806
    Using a caliper gauge, measure the inside diameter of the guide bush.

    Standard bush inside diameter:
    5.510 to 5.530 mm (0.217 to 0.218 in.)

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard oil clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)

    Maximum oil clearance:
    0.08 mm (0.00314 in.)

    If the oil clearance is more than the maximum, replace the valve and guide bush.


INSPECT EXHAUST VALVE GUIDE BUSH

  1. A123806
    Using a caliper gauge, measure the inside diameter of the guide bush.

    Standard bush inside diameter:
    5.510 to 5.530 mm (0.217 to 0.218 in.)

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard oil clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)

    Maximum oil clearance:
    0.10 mm (0.00394 in.)

    If the oil clearance is more than the maximum, replace the valve and guide bush.


INSPECT INTAKE VALVE SEAT

  1. A053830E03
    Apply a light coat of Prussian blue to the valve face.

  1. Lightly press the valve against the seat.

    HINT:
    Do not rotate the valve while pressing it.

  1. Check the valve face and seat.

    1. Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).
      If not, correct the valve seat.

    2. Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
      If not, correct the valve seat.


INSPECT EXHAUST VALVE SEAT

  1. A054861E03
    Apply a light coat of Prussian blue to the valve face.

  1. Lightly press the valve against the seat.

    HINT:
    Do not rotate the valve while pressing it.

  1. Check the valve face and seat.

    1. Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).
      If not, correct the valve seat.

    2. Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
      If not, correct the valve seat.


INSPECT INNER COMPRESSION SPRING

  1. A053807E04
    Using steel squares, measure the deviation of the spring.

    Maximum deviation:
    2.0 mm (0.0787 in.)

    If the deviation is more than the maximum, replace the inner compression spring.

  1. A107610
    Using a vernier caliper, measure the free length of the spring.

    Standard free length:
    51.29 mm (2.02 in.)

    If the free length is not as specified, replace the inner compression spring.

  1. A106674
    Using a spring tester, measure the tension of the inner compression spring when it is compressed to the specified installation length.

    Standard installed tension:
    210 to 226 N (21 to 23 kgf, 47.2 to 50.7 lbf) at 33.4 mm (1.31 in.)

    If the installed tension is not as specified, replace the inner compression spring.


INSPECT VALVE LIFTER

  1. A053835E02
    Using a micrometer, measure the lifter diameter at a position 12.3 to 12.7 mm (0.484 to 0.500 in.) from the top surface.

    Standard lifter diameter:
    30.968 to 30.976 mm (1.2192 to 1.2195 in.)

  1. A050501E01
    Using a caliper gauge, measure the lifter bore diameter of the cylinder head.

    Standard lifter bore diameter:
    31.000 to 31.016 mm (1.220 to 1.221 in.)

  1. Subtract the lifter diameter measurement from the lifter bore diameter measurement.

    Standard oil clearance:
    0.024 to 0.050 mm (0.000945 to 0.00197 in.)

    Maximum oil clearance:
    0.07 mm (0.00276 in.)

    If the oil clearance is more than the maximum, replace the lifter. If necessary, replace the cylinder head sub-assembly.


INSPECT CAMSHAFT THRUST CLEARANCE

  1. A050506E03
    Inspect the clearance on the intake side.

    1. Install the camshaft.

    2. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

      Standard thrust clearance:
      0 to 0.040 mm (0 to 0.00157 in.)

      Maximum thrust clearance:
      0.12 mm (0.00472 in.)

      If the thrust clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.

    3. Remove the camshaft.

  1. A050529E03
    Inspect the clearance on the exhaust side.

    1. Install the camshaft.

    2. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

      Standard thrust clearance:
      0.030 to 0.070 mm (0.00118 to 0.00276 in.)

      Maximum thrust clearance:
      0.10 mm (0.00394 in.)

      If the thrust clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.

    3. Remove the camshaft.


INSPECT CAMSHAFT GEAR BACKLASH

  1. A118106
    for Bank 1:

    1. Install the drive gear to the camshaft timing tube.

    2. Install the camshaft timing tube to the No. 3 camshaft.

    3. Install the No. 3 camshaft and No. 4 camshaft without installing the camshaft sub-gear and No. 5 bearing cap.

    4. Using a dial indicator, measure the backlash.

      Standard backlash:
      0.020 to 0.200 mm (0.000787 to 0.00787 in.)

      Maximum backlash:
      0.30 mm (0.0118 in.)

      If the backlash is more than the maximum, replace the drive gear and No. 4 camshaft.

    5. Remove the No. 3 camshaft and No. 4 camshaft.

    6. Remove the camshaft timing tube from the No. 3 camshaft.

    7. Remove the drive gear from the camshaft timing tube.

  1. A118088
    for Bank 2:

    1. Install the drive gear to the camshaft timing tube.

    2. Install the camshaft timing tube to the camshaft.

    3. Install the camshaft and No. 2 camshaft without installing the camshaft sub-gear and No. 1 bearing cap.

    4. Using a dial indicator, measure the backlash.

      Standard backlash:
      0.020 to 0.200 mm (0.000787 to 0.00787 in.)

      Maximum backlash:
      0.30 mm (0.0118 in.)

      If the backlash is more than the maximum, replace the drive gear and No. 2 camshaft.

    5. Remove the camshaft and No. 2 camshaft.

    6. Remove the camshaft timing tube from the camshaft.

    7. Remove the drive gear from the camshaft timing tube.


INSPECT CAMSHAFT OIL CLEARANCE

  1. A134380E02
    Clean the bearing caps and camshaft journals.

  1. Check the bearings for flaking and scoring.
    If the bearings are damaged, replace the cylinder head sub-assembly.

  1. Place the camshafts on the cylinder head.

  1. Lay a strip of Plastigage across each of the camshaft journals.

  1. Install the bearing caps.

    HINT:
    1. For Bank 1:
      Refer to the following procedures (Click here).
    2. For Bank 2:
      Refer to the following procedures (Click here).

    NOTICE:
    Do not turn the camshaft.

  1. Remove the bearing caps.

    HINT:
    1. For Bank 1:
      Refer to the following procedures (Click here).
    2. For Bank 2:
      Refer to the following procedures (Click here).

  1. A134382E01
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.030 to 0.071 mm (0.00118 to 0.00280 in.)

    Maximum oil clearance:
    0.10 mm (0.00394 in.)

    If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.

  1. Remove the camshafts.

  1. Completely remove the Plastigage.

← DISASSEMBLY (Sep 2011 – Dec 2011)REPLACEMENT (Sep 2011 – Dec 2011) →