2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover.


6. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A175216E01
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.


8. DRAIN ENGINE OIL

  1. A178891
    Remove the oil drain plug and gasket, and drain the engine oil into a container.


9. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A178998
    Remove the 2 nuts and V-bank cover.


10. REMOVE AIR CLEANER HOSE ASSEMBLY

  1. A175163
    Disconnect the vacuum transmitting hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose.


11. REMOVE AIR CLEANER ASSEMBLY

  1. A175167
    Disconnect the clamp and MAF connector.

  1. Remove the 3 bolts and air cleaner.


12. REMOVE IGNITION COIL ASSEMBLY

  1. A176582E01
    Disconnect the 8 ignition coil connectors.

  1. Remove the 8 bolts and pull out the 8 ignition coils.


13. REMOVE SPARK PLUG
  1. Remove the 8 spark plugs.


14. REMOVE NO. 1 RADIATOR HOSE

  1. A178878
    Using needle-nose pliers, grip the claws of the clamps and slide the clamps to remove the radiator hose.


15. REMOVE FAN & GENERATOR V BELT

  1. B000809E02
    Loosen the belt tension by turning the belt tensioner counterclockwise, and then remove the fan and generator V belt.

    HINT:
    The pulley bolt for the belt tensioner has left-hand thread.


16. REMOVE FAN SHROUD

  1. A162053
    Loosen the 4 nuts holding the cooling fan.

  1. A180839E01
    Disconnect the reservoir hose from the upper side of the radiator tank.

  1. w/ Air Cooled Transmission Oil Cooler:
    Detach the claw to open the flexible hose clamp.

  1. Remove the 2 bolts and disconnect the oil cooler tube from the fan shroud.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the cooling fan, and then remove the shroud together with the cooling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.


17. REMOVE NO. 2 RADIATOR HOSE

  1. A180840
    Using needle-nose pliers, grip the claws of the clamps and slide the clamps to remove the radiator hose.


18. REMOVE FRONT FENDER APRON SEAL LH

  1. A176301
    Using a clip remover, remove the 4 clips and fender apron seal.


19. REMOVE FRONT FENDER APRON SEAL LH (w/ KDSS)

  1. A177004
    Using a clip remover, remove the 3 clips and fender apron seal.


20. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Using a clip remover, remove the 3 clips and fender apron seal.


21. DISCONNECT COOLER COMPRESSOR ASSEMBLY

  1. A180811
    Disconnect the connector.

  1. Remove the bolt. Then disconnect the cooler refrigerant suction hose from the cylinder head cover.

  1. Remove the 3 bolts, nut and No. 1 compressor stay and disconnect the cooler compressor.


22. DISCONNECT VANE PUMP ASSEMBLY

  1. C158740
    Disconnect the connector.

  1. C179184
    Remove the 2 bolts and nut. Then disconnect the vane pump.


23. REMOVE GENERATOR ASSEMBLY

  1. A177923
    Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.

  1. Remove the bolt and disconnect the wire harness bracket from the generator.

  1. A177924
    Remove the bolt, 2 nuts and generator.


24. REMOVE OIL COOLER PIPE

  1. A108784E04
    Remove the cap nut and bolt.

  1. Using needle-nose pliers, grip the claws of the clamps and slide the clamps to disconnect the 3 water by-pass hoses and remove the oil cooler pipe.


25. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A110456
    Remove the pulley bolt, cover plate and idler pulley.


26. REMOVE NO. 3 TIMING BELT COVER SUB-ASSEMBLY LH

  1. A178915
    Detach the 3 wire clamps and disconnect the camshaft timing oil control valve connector and control motor connector.

  1. A175247
    Disconnect the camshaft position sensor connector.

  1. Disconnect the camshaft position sensor wire from the 2 wire clamps on the timing belt cover.

  1. Remove the wire grommet from the timing belt cover.

  1. Remove the 4 bolts.

  1. Pull the cover outward, pull the camshaft position sensor wire out of the cover, and remove the cover.


27. REMOVE NO. 3 TIMING BELT COVER SUB-ASSEMBLY RH

  1. A175248
    Remove the 3 bolts, nut and timing belt cover.


28. REMOVE NO. 2 TIMING BELT COVER SUB-ASSEMBLY

  1. A175249
    Remove the 2 bolts and detach the 2 claws, and then remove the No. 2 timing belt cover.


29. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A175250
    Remove the bolt, 2 nuts and V-ribbed belt tensioner.


30. REMOVE FAN BRACKET SUB-ASSEMBLY

  1. A175251
    Remove the 2 nuts, 2 bolts and fan bracket.


31. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

  1. A123364E02
    Using SST, hold the crankshaft damper and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.
    SST
    09213-70011   (09213-70020)
    09330-00021   (09330-00030)

  1. A175246E01
    Using SST and the pulley bolt, remove the crankshaft damper.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)

    HINT:
    Apply a lubricant to the threads and end of SST.


32. REMOVE NO. 1 TIMING BELT COVER

  1. A175252
    Remove the 4 bolts and timing belt cover.


33. REMOVE TIMING BELT COVER SPACER

  1. A175253
    Remove the cover spacer and gasket.


34. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A175256
    Remove the position sensor plate from the crankshaft.


35. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A176500E01
    Temporarily install the pulley bolt.

  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing pulley and camshaft timing pulleys are as shown in the illustration.

    HINT:
    1. If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.
    2. When reusing the timing belt, put a timing mark on the belt where the timing marks on the belt and timing pulley are aligned after rotating the crankshaft.


36. REMOVE TIMING BELT

  1. A175257
    Alternately loosen the 2 bolts, then remove the bolts, timing belt tensioner and dust seal.

  1. Remove the timing belt.


37. DISCONNECT WATER HOSE SUB-ASSEMBLY

  1. A180820E01
    Disconnect the water by-pass hose.

    1. w/ Rear Heater:
      Disconnect the water hoses labeled A and B.

    2. w/o Rear Heater:
      Disconnect the water hoses labeled A.


38. DISCONNECT NO. 1 WATER BY-PASS PIPE (w/ Air Cooled Transmission Oil Cooler)

  1. A175115
    Remove the 2 bolts. Then disconnect the water by-pass pipe from the cylinder head cover RH.


39. REMOVE NO. 2 FUEL HOSE

  1. for engine side:

    1. A176296E01
      Detach the fuel hose clamp.

    2. Detach the lock claw by lifting up the cover, as shown in the illustration.

    3. Pinch and pull the No. 2 fuel hose connector to disconnect the connector from the No. 3 fuel pipe.

      NOTICE:
      1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      2. Do not use any tools to separate the pipe and connector.
      3. Do not forcefully bend or twist the nylon tube.
      4. Check for foreign matter on the pipe seal surface. Clean if necessary.
      5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
      6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

  1. for body side:

    1. A176357E01
      Pinch and pull the No. 2 fuel hose connector to disconnect the connector from the fuel pipe.

      NOTICE:
      1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
      2. Do not use any tools to separate the pipe and connector.
      3. Do not forcefully bend or twist the nylon tube.
      4. Check for foreign matter on the pipe seal surface. Clean if necessary.
      5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
      6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


40. DISCONNECT FUEL HOSE

  1. A176355E02
    Remove the fuel hose clamp.

  1. Pinch and pull the fuel hose connector to disconnect the connector from the fuel pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


41. REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY

  1. A176413E01
    Disconnect the fuel injector connector.

  1. Remove the pulsation damper, upper gasket, fuel hose and lower gasket.

    NOTICE:
    1. Put a cloth or equivalent under the delivery pipe.
    2. Slowly loosen the pulsation damper.


42. SEPARATE WIRE HARNESS

  1. A180578
    Disconnect the 2 air injection control driver connectors.

  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the wire harness clamp.

  1. A180819E01
    Disconnect the 2 clamps and 2 connectors from the engine room relay block.

  1. Disconnect connector A from the engine room relay block.

  1. Disconnect the wire harness clamp from the cylinder head cover LH.


43. REMOVE NO. 1 VENTILATION HOSE

  1. A181858
    Remove the No. 1 ventilation hose from the intake manifold and ventilation valve.


44. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A175263
    Remove the 9 bolts, cylinder head cover and gasket.


45. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A175262
    Remove the 9 bolts, cylinder head cover and gasket.


46. REMOVE SPARK PLUG TUBE GASKET

  1. A175264
    Bend the 8 ventilation case claws of the cylinder head cover to an angle of 90° or more.

  1. Using a screwdriver, pry out the gaskets.

    NOTICE:
    1. Be careful not to damage the cylinder head cover.
    2. Be careful not to damage the gasket when removing it, as the removed gasket needs to be reused when installing a new one.

    HINT:
    Tape the screwdriver tip before use.


47. REMOVE SEMICIRCULAR PLUG
  1. Remove the 4 semicircular plugs from the cylinder heads.


48. REMOVE CAMSHAFT POSITION SENSOR ASSEMBLY

  1. A175764
    Remove the bolt, stud bolt and camshaft position sensor.


49. REMOVE CAMSHAFT TIMING PULLEY

  1. A178897E02
    Using the pulley set bolt, turn the crankshaft counterclockwise by approximately 45°.

    NOTICE:
    If the timing belt is disengaged, having the crankshaft pulley at a wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley and camshaft, causing damage. So always set the crankshaft pulley at the correct angle.

  1. A160790
    Hold the hexagonal portion of the camshaft with a wrench and remove the 4 bolts indicated by the arrows in the illustration and timing pulley.

    NOTICE:
    1. Do not loosen or remove the 4 bolts that are not indicated by the arrows in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the timing tube assembly with a new one.
    2. Be careful not to damage the cylinder head with the wrench.


50. REMOVE CAMSHAFT TIMING PULLEY SUB-ASSEMBLY LH

  1. A160789
    Hold the hexagonal portion of the camshaft with a wrench and remove the 4 bolts indicated by the arrows in the illustration and timing pulley.

    NOTICE:
    1. Do not loosen or remove the 4 bolts that are not indicated by the arrows in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the timing tube assembly with a new one.
    2. Be careful not to damage the cylinder head with the wrench.


51. REMOVE REAR NO. 2 TIMING BELT PLATE RH

  1. A175265
    Remove the 2 bolts, stud bolt and timing belt plate.


52. REMOVE REAR NO. 2 TIMING BELT PLATE LH

  1. A176456
    Remove the 2 bolts and timing belt plate.


53. REMOVE CAMSHAFT (for Bank 1)

  1. A176464E01
    Bring the service bolt hole of the sub-gear upward by turning the hexagonal portion of the exhaust camshaft with a wrench.

  1. Secure the sub-gear to the driven gear with a service bolt.

    Recommended Service Bolt:
    Thread Diameter
    Thread Pitch
    Bolt Length
    6.0 mm
    1.0 mm
    16 to 20 mm (0.630 to 0.787 in.)

    HINT:
    When removing the camshafts, make sure that the torsional spring force of the sub-gear has been eliminated by the above operation.

  1. A185563E01
    Using a wrench, turn the camshaft so that the timing marks (2 dot marks each) on the camshaft drive and driven gears are aligned, as shown in the illustration.

    HINT:
    The position shown in the illustration is the most stable position for the exhaust camshaft.

  1. A176462E01
    Uniformly loosen and remove the 22 bearing cap bolts in several steps, in the order shown in the illustration.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged. To avoid this, the following steps should be carried out.

  1. A160810
    Remove the cap bolts, 4 seal washers, oil feed pipe, 9 bearing caps, camshaft housing plug, oil control valve filter and camshafts.

    NOTICE:
    1. Do not forcibly pry the camshaft with a tool.
    2. Do not damage the reception part of the thrust on the cylinder head side.

    HINT:
    Arrange the bearing caps in the correct order.


54. REMOVE CAMSHAFT (for Bank 2)

  1. A176459E01
    Bring the service bolt hole of the sub-gear upward by turning the hexagonal portion of the exhaust camshaft with a wrench.

  1. Secure the sub-gear to the driven gear with a service bolt.

    Recommended Service Bolt:
    Thread Diameter
    Thread Pitch
    Bolt Length
    6.0 mm
    1.0 mm
    16 to 20 mm (0.630 to 0.787 in.)

    HINT:
    When removing the camshafts, make sure that the torsional spring force of the sub-gear has been eliminated by the above operation.

  1. A185564E01
    Using a wrench, turn the camshaft so that the timing marks (1 dot mark each) on the camshaft drive and driven gears are aligned, as shown in the illustration.

    HINT:
    The position shown in the illustration is the most stable position for the exhaust camshaft.

  1. A176461E01
    Uniformly loosen and remove the 22 bearing cap bolts in several steps, in the order shown in the illustration.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged. To avoid this, the following steps should be carried out.

  1. A160809
    Remove the cap bolts, 4 seal washers, oil feed pipe, 9 bearing caps, camshaft housing plug, oil control valve filter and camshafts.

    NOTICE:
    1. Do not forcibly pry the camshaft with a tool.
    2. Do not damage the reception part of the thrust on the cylinder head side.

    HINT:
    Arrange the bearing caps in the correct order.


55. INSPECT CAMSHAFT TIMING TUBE ASSEMBLY

  1. A134376
    Using a micrometer, measure the journal diameter.

    Standard journal diameter:
    39.955 to 39.964 mm (1.5730 to 1.5734 in.)

    If the journal diameter is not as specified, check the oil clearance. If necessary, replace the camshaft and cylinder head.

  1. Install the camshaft timing tube to the camshaft (Click here).

  1. Check the lock of the camshaft timing tube.

    1. Check that the camshaft timing tube is locked.

  1. A180829E01
    Release the lock pin.

    1. Clean the camshaft timing tube journal with non-residue solvent.

    2. Wrap tape around the entire journal to block the 4 oil holes as shown in the illustration.

    3. Open a hole in the tape at 2 places, one in the retard side oil hole and one in the advance side oil hole as shown in the illustration.

    4. A180830E01
      Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 open oil holes (the advance side oil hole and the retard side oil hole).

      NOTICE:
      Cover the oil holes with a piece of cloth when applying pressure to keep oil from splashing.

      HINT:
      The lock pin will be released when air pressure is applied.

    5. A180831E01
      Check that the camshaft timing tube revolves in the advance direction when reducing the air pressure applied to the retard side oil hole.

    6. When the camshaft timing tube reaches the most advanced position, release the air pressure from the retard side oil hole and advance side oil hole, in that order.

      NOTICE:
      1. Do not release the air pressure from the advance side oil hole first. The tube may abruptly shift in the retard direction and break the lock pin.
      2. When releasing the air pressure from the retard side oil hole, do not release the air pressure too quickly to prevent damage.

  1. Check for smooth rotation.

    1. Apply 60 kPa (0.6 kgf/cm2, 8.7 psi) of air pressure to the retard side oil hole to release the lock pin.

    2. Turn the camshaft timing tube within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the camshaft timing tube turns smoothly.

      NOTICE:
      Do not use air pressure to perform the smooth rotation check. Always perform the check by hand.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing tube is locked at the most retarded position.

  1. Remove the camshaft timing tube (Click here).


56. REMOVE CAMSHAFT TIMING TUBE ASSEMBLY

  1. A118101E04
    Mount the hexagonal portion of the camshaft in a vise.

    NOTICE:
    1. Be careful not to damage the camshaft.
    2. Do not loosen or remove the 4 bolts shown in the illustration. If any of them are loosened or removed, the backlash of the gear in the timing tube will go out of adjustment. In this case, replace the timing tube assembly with a new one.

  1. Remove the screw plug and seal washer.

  1. A118091E01
    Using a 10 mm hexagon wrench, remove the bolt and timing tube.


57. REMOVE CAMSHAFT DRIVE GEAR

  1. A054029E07
    Using SST and a 5 mm hexagon wrench, remove the 4 bolts, drive gear and oil seal.
    SST
    09960-10010   (09962-01000, 09963-00500)

    NOTICE:
    Be careful not to damage the timing tube.


58. REMOVE CAMSHAFT SUB-GEAR

  1. A054968E01
    Mount the hexagonal portion of the camshaft in a vise.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A054969E02
    Using SST, turn the sub-gear clockwise, and remove the service bolt.
    SST
    09960-10010   (09962-01000, 09963-00500)

  1. A050627E01
    Using snap ring pliers, remove the snap ring.

  1. Remove the wave washer, sub-gear and gear spring.

    HINT:
    Arrange the camshaft sub-gears and gear spring (LH and RH).

← COMPONENTS (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →