2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL FRONT ENGINE MOUNTING INSULATOR LH

  1. A176552
    Install the mounting insulator with the nut.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }


2. INSTALL FRONT ENGINE MOUNTING INSULATOR RH

  1. A176553
    Install the mounting insulator with the nut.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

  1. Connect the vacuum hose.


3. INSTALL NO. 1 AND NO. 2 ENGINE HANGER

  1. A181664E01
    Install the No. 1 and No. 2 engine hangers to the cylinder head RH and LH with the 4 bolts as shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Engine Hanger Part No. 
    Item
    Part No.
    No. 1 engine hanger
    12281-51040
    No. 2 engine hanger
    12282-51040
    Bolt
    91671-80825


4. REMOVE ENGINE STAND
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Lift the engine, and remove it from the engine stand.


5. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. A177364E01
    Install the rear crankshaft balancer weight labeled C, ring gear labeled B and rear drive plate spacer labeled A with 8 new bolts.

  1. A185177
    Using a wrench, hold the crankshaft.

  1. A177363E01
    Uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    182 N*m{ 1856 kgf*cm , 134 ft.*lbf }


6. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A177365E01
    Temporarily install the flywheel with 8 new bolts.

    NOTICE:
    1. Align the crankshaft knock pin and flywheel knock pin hole.
    2. Do not strike or damage the flywheel installation bolts. Be sure to handle them carefully.
    3. Make sure there is no oil on the bolts.

  1. A185177
    Using a wrench, hold the crankshaft.

  1. Uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    182 N*m{ 1856 kgf*cm , 134 ft.*lbf }


7. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

C173323E01
  1. Insert SST into the clutch disc, then insert the clutch disc into the flywheel.

    SST
    09301-00120  

    NOTICE:
    Take care not to insert the clutch disc in the wrong direction.


8. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

C173324E01
  1. Align the matchmark on the clutch cover with the one on the flywheel.

  1. In the order shown in the illustration, temporarily install the 8 bolts starting from the bolt located near the knock pin on the top.

  1. Check that the disc is in the center by lightly moving SST up and down, and left and right.

    SST
    09301-00120  

  1. Evenly tighten the bolts by following the order shown in the illustration.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


9. INSTALL ENGINE ASSEMBLY

  1. A174842
    Slowly lower the engine into the engine compartment.

  1. Install the 4 bolts to the front mounting insulator RH and LH.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }

  1. Remove the 4 bolts and No. 1 and No. 2 engine hangers.


10. INSTALL CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177337
    Install the tube with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


11. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
  1. Install the manual transmission unit assembly (Click here).


12. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
  1. Install the automatic transmission assembly (Click here).


13. INSTALL NO. 2 INTAKE MANIFOLD

  1. A174810
    Install a new gasket and the No. 2 intake manifold with the 9 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


14. INSTALL NO. 1 INTAKE MANIFOLD

  1. A174809
    Install a new gasket and the No. 1 intake manifold with the 9 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


15. INSTALL NO. 1 WATER BY-PASS PIPE

  1. A174808E01
    Temporarily install a new gasket and the No. 1 water by-pass pipe with the union bolt and bolt.

  1. Tighten the union bolt and bolt in the order shown in the illustration.

    Torque:
    for union bolt:
    59 N*m{ 600 kgf*cm , 43 ft.*lbf }
    for bolt:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


16. INSTALL FUEL COOLER ASSEMBLY

  1. A176378
    Install the fuel cooler with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


17. CONNECT NO. 6 WATER BY-PASS HOSE

A174806

18. INSTALL NO. 4 NOZZLE LEAKAGE PIPE

  1. A174805E01
    Temporarily install a new gasket and the No. 4 nozzle leakage pipe with the union bolt and bolt.

  1. Tighten the union bolt and bolt in the order shown in the illustration.

    Torque:
    for union bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the No. 2 fuel hose to the fuel cooler.


19. INSTALL NO. 3 NOZZLE LEAKAGE PIPE

  1. A174804E01
    Temporarily install a new gasket and the No. 3 nozzle leakage pipe with the union bolt and bolt.

  1. Tighten the union bolt and bolt in the order shown in the illustration.

    Torque:
    for union bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the No. 1 fuel hose to the fuel cooler.


20. INSTALL EGR COOLER INSULATOR (w/ EGR System)

A174803

21. INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

  1. A174802
    Connect the No. 5 water by-pass hose to the water by-pass outlet.

  1. A174801E01
    Install 2 new gaskets and the EGR valve with EGR cooler with the 6 bolts labeled A and 4 bolts labeled B shown in the illustration.

    Torque:
    for bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt B:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    HINT:
    The gasket claws should face toward the No. 1 and No. 2 EGR pipes.


22. INSTALL EGR PIPE INSULATOR (w/ EGR System)

  1. A174800
    Install the EGR pipe insulator with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    If the No. 1 and No. 2 EGR pipe insulator installation stay is deformed, or the bolt holes of the EGR pipe insulator do not align, replace the No. 1 and No. 2 EGR pipes as a set.


23. INSTALL INTAKE MANIFOLD INSULATOR (w/ EGR System)

A174799

24. INSTALL NO. 3 INTAKE MANIFOLD

A174867E01
  1. Set 2 new gaskets to the No. 1 and No. 2 intake manifolds.

  1. Install the No. 3 intake manifold with the 16 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Bolt Length 
    Item
    Length
    Bolt A
    25 mm (0.984 in.)
    Bolt B
    70 mm (2.76 in.)


25. CONNECT NO. 2 ENGINE WIRE

  1. A174797E01
    Connect the No. 2 engine wire with the 3 bolts.

    Torque:
    for bolt A:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Attach the 2 wire harness clamps.


26. INSTALL INTAKE PIPE

  1. A174796
    w/ EGR System:
    Install 2 new gaskets and the intake pipe with the 6 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A180252
    w/o EGR System:
    Install a new gasket and the intake pipe with the 4 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


27. INSTALL NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174791

28. INSTALL NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174795

29. INSTALL COMMON RAIL ASSEMBLY RH

  1. A176411
    Install the common rail with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


30. INSTALL INJECTION PIPE RH

  1. A174793
    Using a union nut wrench, install the 4 new injection pipes.

    Torque:
    without union nut wrench:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }
    with union nut wrench:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

    NOTICE:
    Make sure there is no damage or foreign matter on the seal surfaces.


    HINT:
    A185179E01
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).
    2. Make sure the union nut wrench and the torque wrench are connected in a straight line.

  1. A174788
    w/ Intercooler:
    Install the 4 injection pipe clamps with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


31. INSTALL NO. 5 INJECTION PIPE SUB-ASSEMBLY

  1. A174696
    Temporarily install a new No. 5 injection pipe by hand.

    NOTICE:
    Make sure there is no damage or foreign matter on the seal surfaces.

  1. A185242
    Temporarily install the used gasket and No. 2 fuel pipe with the nut, bolt and union bolt.

  1. A185243
    Temporarily install the No. 2 injection pipe clamp with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. A174696
    Using a union nut wrench, tighten the No. 5 injection pipe ends.

    Torque:
    without union nut wrench:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }
    with union nut wrench:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }


    HINT:
    A185179E01
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).
    2. Make sure the union nut wrench and the torque wrench are connected in a straight line.

  1. A185243
    Remove the bolt and No. 2 injection pipe clamp.

  1. A185242
    Remove the union bolt and gasket.

  1. Remove the bolt, nut and No. 2 fuel pipe.


32. CONNECT FUEL PUMP MOTOR WIRE

  1. A174792
    Install the fuel pump motor wire bracket to the No. 3 intake manifold with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the connector to the fuel supply pump.


33. INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

  1. A174697
    Install the fuel filter to injection pump fuel pipe with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 2 hoses to the fuel pipe.


34. INSTALL COMMON RAIL ASSEMBLY LH

  1. A176404
    Install the common rail with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


35. INSTALL INJECTION PIPE LH

  1. A174789
    Using a union nut wrench, install the 4 new injection pipes.

    Torque:
    without union nut wrench:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }
    with union nut wrench:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

    NOTICE:
    Make sure there is no damage or foreign matter on the seal surfaces.


    HINT:
    A185179E01
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).
    2. Make sure the union nut wrench and the torque wrench are connected in a straight line.

  1. A174694
    w/ Intercooler:
    Install the 4 injection pipe clamps with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


36. CONNECT NO. 6 INJECTION PIPE SUB-ASSEMBLY

  1. A185542
    w/ EGR System:

    1. Temporarily install a new No. 6 injection pipe to the common rail LH and RH.

      NOTICE:
      Make sure there is no damage or foreign matter on the seal surfaces.

    2. Install the 2 No. 2 injection pipe clamps with the 2 nuts.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. Using a union nut wrench, tighten the No. 6 injection pipe ends.

      Torque:
      without union nut wrench:
      34 N*m{ 347 kgf*cm , 25 ft.*lbf }
      with union nut wrench:
      31 N*m{ 316 kgf*cm , 23 ft.*lbf }


      HINT:
      A185179E01
      1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).
      2. Make sure the union nut wrench and the torque wrench are connected in a straight line.

  1. A174695
    w/o EGR System:

    1. Temporarily install a new No. 6 injection pipe to the common rail LH and RH.

      NOTICE:
      Make sure there is no damage or foreign matter on the seal surfaces.

    2. Install the bracket to the No. 3 intake manifold with the bolt.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    3. Install the No. 2 injection pipe clamp with the nut.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    4. Using a union nut wrench, tighten the No. 6 injection pipe ends.

      Torque:
      without union nut wrench:
      34 N*m{ 347 kgf*cm , 25 ft.*lbf }
      with union nut wrench:
      31 N*m{ 316 kgf*cm , 23 ft.*lbf }


      HINT:
      A185179E01
      1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).
      2. Make sure the union nut wrench and the torque wrench are connected in a straight line.


37. INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY

NOTICE:
A174693E01
Check for damage and foreign matter on the fuel pipe installation surface of the supply pump.
If there is foreign matter, remove it from the installation surface. If the installation surface is damaged, replace the fuel supply pump.

  1. Temporarily install a new gasket and the No. 2 fuel pipe with the union bolt, nut and bolt.

  1. Tighten the union bolt, nut and bolt in the order shown in the illustration.

    Torque:
    for union bolt:
    10 N*m{ 105 kgf*cm , 8 ft.*lbf }
    for bolt and nut:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the No. 2 injection pipe clamp with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the fuel hose to the No. 5 nozzle leakage pipe.


38. CONNECT ENGINE WIRE

  1. Rear Side:

    1. A174757E01
      Install the glow plug wire harness with the nut labeled A.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    2. Connect the 2 common rail connectors.

    3. Install the engine wire harness protector with the 2 bolts labeled B.

    4. Install the 2 ground wires with the 2 bolts labeled C.

      Torque:
      8.4 N*m{ 87 kgf*cm , 74 in.*lbf }

  1. LH Side:

    1. A174756E01
      Install the engine wire protector with the 2 bolts labeled A.

    2. Connect the 8 connectors.

    3. Install the engine wire harness bracket with the bolt labeled B.

    4. for RHD:
      Connect the wire harness with the wire harness clamp holder labeled C.

    5. A174755
      Attach the 3 wire harness clamps and connect the 2 connectors.

    6. A174744
      Connect the 4 connectors to the injection driver.

    7. Install the ground wire with the bolt.

      Torque:
      8.4 N*m{ 87 kgf*cm , 74 in.*lbf }

    8. Connect the wire harness holder to the relay block.

    9. Connect the 4 connectors to the relay block.

    10. Connect the wire harness with the wire harness clamp holder.

    11. A174747E01
      for RHD:
      Connect the wire harness with the wire harness clamp holder.

    12. for RHD:
      Connect the ECM connector to the ECM.

    13. for RHD:
      Attach the wire harness tab labeled A to the relay block.

    14. Connect the 4 connectors to the relay block.

    15. A174745
      Connect the generator positive (+) cable to the body panel with the 2 clamps.

    16. Attach the generator positive (+) cable holder to the relay block, and install the cable to the relay block with the nut.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    17. A174743E01
      Connect the wire harness with the wire harness clamp holder labeled B, and attach the ground wire clamp to the relay block side labeled A.

    18. Install the ground wire to the body panel with the bolt.

      Torque:
      8.4 N*m{ 87 kgf*cm , 74 in.*lbf }

  1. RH Side:

    1. A174760
      w/ Winch:
      Install the ground wire with the bolt.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    2. A174750E01
      Install the engine wire harness protector with the 3 bolts labeled A.

    3. Connect the 7 connectors.

    4. Install the wire harness bracket with the bolt labeled B.

    5. Install the glow plug wire harness with the nut labeled C.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    6. A174759
      for RHD:
      Connect the wire harness with the wire harness holder.

    7. A179104E01
      for LHD:
      Connect the wire harness with the wire harness clamp holder.

    8. for LHD:
      Connect the ECM connector to the ECM.

    9. for LHD:
      Attach the wire harness tab labeled A to the relay block.

    10. for LHD:
      Connect the 4 connectors to the relay block.


39. INSTALL NO. 4 WATER BY-PASS PIPE

  1. A174691
    w/ EGR System:
    Connect the 4 water hose ends, and temporarily install the No. 4 water by-pass pipe with the 2 bolts and nut.

  1. First tighten the 2 bolts and then tighten the nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A174692
    w/o EGR System:
    Connect the 3 water hose ends, and temporarily install the No. 4 water by-pass pipe with the 2 bolts and nut.

  1. First tighten the 2 bolts and then tighten the nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


40. INSTALL NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

  1. A174688
    Connect the 2 water hose ends, and install the No. 3 water by-pass pipe with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


41. CONNECT FUEL HOSE

A174685E01

42. INSTALL NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174714
    Connect the No. 1 air cleaner pipe to the No. 1 intake air connector pipe.

  1. Install the pipe with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }


43. INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

  1. A174689
    Connect the 4 water hose ends, and install the water pipe with the 4 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


44. INSTALL NO. 2 INTAKE AIR CONNECTOR PIPE

  1. A181658E01
    Install the No. 2 intake air connector pipe to the No. 2 inlet compressor elbow.

    NOTICE:
    Make sure there is no gap between the air pipe and hose stopper on the elbow side.

  1. A174713
    Install the bolt of the air pipe.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Do not excessively pull the air pipe towards the front of the engine.

  1. Tighten the hose clamp on the elbow side.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    HINT:

    1. A182762E01
      Align the 2 protrusions of the air pipe and elbow.
    2. Install the air pipe so that the protrusion on the pipe side is within the range of the protrusion on the elbow side.
    3. After tightening, a gap between the air pipe and hose stopper on the elbow side is acceptable.

    4. A185560E01
      Make sure the direction of the hose clamp is as shown in the illustration.

  1. A174712
    w/ Intercooler:
    Connect the vacuum hose.


45. ADJUST COMPRESSOR OIL
  1. When replacing the compressor and magnetic clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor and magnetic clutch before installation.

    Standard:
    VDJ200L-GNMNZV, GNTNZV, GPMNZV:
    (Oil capacity inside the new compressor and magnetic clutch: 140 + 15 cc (4.7 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed from the new compressor when replacing)
    Except VDJ200L-GNMNZV, GNTNZV, GPMNZV:
    (Oil capacity inside the new compressor and magnetic clutch: 135 + 15 cc (4.6 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed from the new compressor when replacing)

    NOTICE:
    1. When checking the compressor oil level, follow the A/C system precautions.
    2. If a new compressor and magnetic clutch is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.
    3. If the volume of oil remaining in the removed compressor and magnetic clutch is too small, check for oil leakage.
    4. Be sure to use ND-OIL 8 or equivalent for compressor oil.


46. INSTALL COOLER COMPRESSOR ASSEMBLY

  1. A181683E01
    Temporarily install the cooler compressor with the 4 bolts.

  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. A174754
    Attach the 3 wire harness clamps and connect the 4 connectors.


47. INSTALL SUCTION HOSE SUB-ASSEMBLY

  1. E154191
    Remove the attached vinyl tape from the cooler refrigerant suction hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the suction hose.

  1. Connect the suction hose to the cooler compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


48. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

E154190
  1. Remove the attached vinyl tape from the discharge hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the discharge hose.

  1. Connect the discharge hose to the cooler compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


49. INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174711
    Connect the No. 2 air cleaner pipe to the No. 2 intake air connector pipe.

  1. Connect the ventilation hose to the oil separator.

  1. Install the pipe with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }


50. INSTALL NO. 2 AIR TUBE ASSEMBLY

  1. A174707
    Apply a light coat of washer fluid to a new O-ring, and install it to the No. 2 air tube.

  1. Install the No. 2 air tube with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


51. INSTALL NO. 4 AIR TUBE

  1. A174723E01
    Install the No. 4 air tube with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.

  1. A174690
    Install the suction hose with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


52. INSTALL NO. 2 AIR HOSE

  1. A177379E01
    Connect the No. 2 air hose with the hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    1. Align the paint mark of the air hose with the protrusion and push in the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).
    2. Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).
    3. Make sure the direction of the hose clamp is as shown in the illustration.


53. INSTALL NO. 1 AIR TUBE ASSEMBLY

  1. A174709
    Apply a light coat of washer fluid to a new O-ring, and install it to the No. 1 air tube.

  1. Install the No. 1 air tube with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


54. INSTALL NO. 3 AIR TUBE

  1. A174722E01
    Install the No. 3 air tube with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.

  1. A174752
    Install the wire harness bracket with the bolt.

  1. A174751
    Install the ground wire with the nut, and attach the wire harness clamp.

    Torque:
    8.4 N*m{ 87 kgf*cm , 74 in.*lbf }


55. INSTALL NO. 1 AIR HOSE

  1. A177378E01
    Connect the No. 1 air hose with the hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    1. Align the paint mark of the air hose with the protrusion and push in the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).
    2. Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).
    3. Make sure the direction of the hose clamp is as shown in the illustration.


56. INSTALL DIESEL THROTTLE BODY ASSEMBLY LH

A163131
  1. Install a new gasket to the intake pipe.

  1. Install the throttle body with the 2 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the throttle position sensor connector.

  1. Connect the throttle motor connector.


57. INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

  1. A163348
    Install the bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A185145
    for Manual Transmission:

    1. Connect the clutch tube to release cylinder 2 way with the bolt.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Check that the union nut is tightened to the specified torque.

      Torque:
      without union nut wrench:
      15 N*m{ 154 kgf*cm , 11 ft.*lbf }
      with union nut wrench:
      14 N*m{ 141 kgf*cm , 10 ft.*lbf }


58. INSTALL NO. 1 GAS FILTER

  1. A163347
    Install the gas filter.

  1. Connect the hose to the intake pipe.


59. INSTALL TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

A182469
  1. Temporarily install the flare nut of the tube connector to flexible hose tube to the clutch tube to release cylinder 2 way by hand.

  1. A177031E01
    Temporarily install the tube connector to flexible hose tube with the 2 bolts.

  1. Tighten the bolt labeled A.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Tighten the bolt labeled B after installing the clutch hose.


60. INSTALL AIR TUBE SUB-ASSEMBLY LH

A181564E01
  1. Install the air tube to the throttle body.

  1. Align the embossed mark of the throttle body with the paint mark of the No. 4 air hose.

  1. A163828E03
    Tighten the hose clamp so that it is 7 to 11 mm (0.276 to 0.433 in.) from the end of the hose as shown in the illustration.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }


61. INSTALL CLUTCH HOSE (for Manual Transmission)

  1. A182467E01
    Connect the clutch hose to the air tube with the bolt labeled A.

  1. Temporarily install the clutch hose to the clutch master cylinder tube to flexible hose tube and tube connector to flexible hose tube, and fix it in place with the 2 clips.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Tighten the bolt labeled B.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Tighten the flexible hose tube.

    NOTICE:
    1. Do not bend or damage the flexible hose tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tube from the connecting points.

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure union nut wrench and the wrench are connected in a straight line.


    1. A177033E01
      Using a 10 mm union nut wrench, tighten the 2 flare nuts of the flexible hose tube.

      Torque:
      without union nut wrench:
      15 N*m{ 154 kgf*cm , 11 ft.*lbf }
      with union nut wrench:
      14 N*m{ 141 kgf*cm , 10 ft.*lbf }

    2. A184226E01
      Using a 10 mm union nut wrench, tighten the flare nut of the flexible hose tube.

      Torque:
      without union nut wrench:
      15 N*m{ 154 kgf*cm , 11 ft.*lbf }
      with union nut wrench:
      14 N*m{ 141 kgf*cm , 10 ft.*lbf }


62. INSTALL DIESEL THROTTLE BODY ASSEMBLY RH

A163132
  1. Install a new gasket to the intake pipe.

  1. Install the throttle body with the 2 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the throttle position sensor connector.

  1. Connect the throttle motor connector.


63. INSTALL AIR TUBE SUB-ASSEMBLY RH

A181564E01
  1. Install the air tube to the throttle body.

  1. Align the embossed mark of the throttle body with the paint mark of the No. 4 air hose.

  1. A163828E03
    Tighten the hose clamp so that it is 7 to 11 mm (0.276 to 0.433 in.) from the end of the hose as shown in the illustration.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }


64. INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A170321
    Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the No. 2 engine oil level dipstick guide.

  1. Install the No. 2 engine oil level dipstick guide with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the ventilation hose to the cylinder head cover RH.

  1. A174875
    Connect the wire harness clamp to the No. 2 engine oil level dipstick guide bracket.


65. CONNECT WATER HOSE SUB-ASSEMBLY

A174687E01

66. INSTALL NO. 2 COOL AIR INLET (w/o Intercooler)

  1. A257096E01
    Install a new gasket to the air tube LH.

    HINT:
    Install the gasket with the protrusion facing as shown in the illustration.

  1. A257029
    Install the No. 2 cool air inlet with the 3 nuts and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A257031E01
    Connect the No. 2 air hose to the No. 2 cool air inlet.

  1. Tighten the No. 2 air hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    1. Align the paint mark of the air hose with the protrusion and push on the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).
    2. Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).
    3. Make sure the direction of the hose clamp is as shown in the illustration.


67. INSTALL NO. 1 COOL AIR INLET (w/o Intercooler)

  1. A257095E01
    Install a new gasket to the air tube RH.

    HINT:
    Install the gasket with the protrusion facing as shown in the illustration.

  1. A257028
    Install the No. 1 cool air inlet with the 3 nuts and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the vacuum hose, intake air temperature sensor connector and turbo pressure sensor connector.

  1. A257030E01
    Connect the No. 1 air hose to the No. 1 cool air inlet.

  1. Tighten the No. 1 air hose clamp.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    1. Align the paint mark of the air hose with the protrusion and push on the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).
    2. Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).
    3. Make sure the direction of the hose clamp is as shown in the illustration.


68. INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)

  1. A174863E01
    Install a new gasket to the air tube RH.

    HINT:
    Install the gasket with the protrusion facing as shown in the illustration.

  1. A179105E01
    Install a new gasket to the air tube LH.

    HINT:
    Install the gasket with the protrusion facing as shown in the illustration.

  1. A174705E01
    Align the No. 1 and No. 2 air hoses and intercooler pipes and connect them, and install the intercooler with the 2 bolts and 2 nuts labeled A in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Temporarily install the 4 nuts labeled B in the illustration.

  1. Tighten the air tube LH and RH with the 4 nuts labeled B shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A174704
    Connect the vacuum hose, intake air temperature sensor connector and turbo pressure sensor connector.

  1. A174865E01
    Tighten the clamp of the No. 2 air hose.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    1. Align the paint mark of the air hose with the protrusion and push in the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).
    2. Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).
    3. Make sure the direction of the hose clamp is as shown in the illustration.

  1. A179106E01
    Tighten the clamp of the No. 1 air hose.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

    HINT:
    1. Align the paint mark of the air hose with the protrusion and push in the air hose so that distance B is 0 to 3 mm (0 to 0.118 in.).
    2. Position the clamp so that distance A is 2 to 6 mm (0.0787 to 0.236 in.).
    3. Make sure the direction of the hose clamp is as shown in the illustration.


69. CONNECT FUEL TUBE

  1. A177338
    Install new No. 1 and No. 3 fuel tube clamps.

  1. Connect the 3 fuel tubes to the clamps.


70. CONNECT FRONT DIFFERENTIAL BREATHER TUBE

71. ADD ENGINE OIL
  1. Add fresh oil.

    Standard Engine Oil:
    Oil Grade
    Oil Viscosity (SAE)
    G-DLD-1, API CF-4, API CF or ACEA B1
    (You may also use API CE or CD)
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50
    (5W-30 is best choice for fuel economy and good starting in cold weather).


    Standard Capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    9.2 liters (9.7 US qts, 8.1 Imp. qts)
    Drain and refill without oil filter change
    8.2 liters (8.7 US qts, 7.2 Imp. qts)
    Dry fill
    9.9 liters (10.5 US qts, 8.7 Imp. qts)

  1. Install the oil filler cap.


72. INSTALL RADIATOR ASSEMBLY

  1. A174155
    Install the radiator with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


73. CONNECT RADIATOR SIDE DEFLECTOR LH

  1. A174322
    Install the side deflector with the 4 clips.


74. CONNECT RADIATOR SIDE DEFLECTOR RH (for Manual Transmission)

  1. A174321
    Install the deflector with the 4 clips.


75. INSTALL TRANSMISSION OIL COOLER AIR DUCT (for Automatic Transmission)

  1. A184326
    Install the oil cooler air duct with the 4 bolts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }


76. INSTALL FRONT BUMPER COVER

B181927

HINT:
For the front bumper cover with garnish, use the procedures described below.

  1. w/ Headlight Cleaner System:
    Connect the headlight cleaner hose.

  1. w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Attach the 10 claws to install the bumper cover.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Connect the No. 4 engine room wire connector and attach the 10 claws to install the bumper cover.

  1. Install the 3 clips, 4 screws and 4 bolts.

    B180995

  1. Using a T30 "TORX" socket, install the 6 screws.

    B180994E01


77. INSTALL RADIATOR GRILLE

B180899
  1. Attach the 2 clips and 8 claws to install the radiator grille.

  1. Install the 3 screws.


78. INSTALL FRONT BUMPER WINCH COVER (w/ Winch)

79. INSTALL FAN PULLEY

80. INSTALL FAN SHROUD WITH FAN
  1. Install the shroud together with the fluid coupling fan between the radiator and engine components.

    NOTICE:
    Be careful not to damage the radiator core.

  1. A179253
    Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts.

    HINT:
    Tighten the nuts as much as possible by hand.

  1. A174737
    Attach the shroud claws to the radiator.

  1. Install the shroud with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A179253
    Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


81. INSTALL OIL COOLER TUBE (for Automatic Transmission)

  1. C167866E01
    Temporarily install the oil cooler tube to the fan shroud with the bolt labeled A. Install the bolt labeled B. Then tighten the bolt labeled A to the specified torque.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C175576E01
    Connect the inlet No. 4 oil cooler hose as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  1. C175577
    Connect the inlet No. 2 and No. 3 oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  1. C167862E01
    Connect the inlet and outlet No. 1 oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  1. Pass the hose through the flexible hose clamp and close the clamp shown in the illustration.


82. INSTALL V-RIBBED BELT

  1. A179095
    Attach a wrench to the V-ribbed belt tensioner bracket and turn the wrench clockwise.

  1. A174850
    Install the V-ribbed belt as shown in the illustration.

  1. A185945E01
    Check that the belt fits properly in the ribbed grooves.

    HINT:
    Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.
    If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt.


83. INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)

  1. A177431
    Align the No. 3 idler pulley bracket knock pin and No. 1 idler pulley bracket knock pin hole and install the No. 3 idler pulley with the nut.

    Torque:
    88 N*m{ 898 kgf*cm , 64 ft.*lbf }


84. INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)

  1. A177430
    Install the collar, No. 1 idler pulley and cover with the bolt.

    Torque:
    49 N*m{ 495 kgf*cm , 36 ft.*lbf }


85. INSTALL V-RIBBED BELT (w/ Viscous Heater)

  1. A174851
    Install the V-ribbed belt as shown in the illustration.

  1. A174848
    Temporarily install the lock nut, and turn the bolt clockwise.

  1. A177434
    Using a belt tension gauge, adjust belt tension.

    Standard Belt Tension:
    Item
    Specified Condition
    New belt
    400 to 650 N (41 to 66 kgf, 89.9 to 146.1 lbf)
    Used belt
    300 to 500 N (31 to 51 kgf, 67.4 to 112.4 lbf)

    HINT:
    1. A "new belt" is a belt which has been used for less than 5 minutes on a running engine.
    2. A "used belt" is a belt which has been used on a running engine for 5 minutes or more.
    3. After installing a new belt, run the engine for approximately 5 minutes and then recheck the tension.

  1. A181677
    Tighten the nut.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. A185945E01
    Check that the belt fits properly in the ribbed grooves.

    HINT:
    Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.
    If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt.


86. CONNECT NO. 2 RADIATOR HOSE

87. CONNECT NO. 1 RADIATOR HOSE

88. INSTALL RADIATOR RESERVOIR ASSEMBLY

  1. A174738E01
    Install the radiator reservoir with the 3 bolts.

  1. Connect the 2 hoses to the upper radiator tank and water inlet.

    HINT:
    Make sure the directions of the hose clamps are as shown in the illustration.


89. INSTALL NO. 1 OIL RESERVOIR BRACKET

  1. A184319
    Install a new bracket with the 2 bolts.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }


90. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A177429
    Install the vane pump oil reservoir to the bracket.


91. INSTALL AIR CLEANER CASE

  1. A174700
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Attach the wire harness clamp to the air cleaner case.


92. INSTALL AIR CLEANER FILTER ELEMENT

93. INSTALL INTAKE AIR CONNECTOR

  1. A174710
    Connect the intake air connector to the No. 1 and No. 2 air cleaner pipes.

  1. Install the connector with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the 2 hose clamps.

    Torque:
    6.3 N*m{ 64 kgf*cm , 56 in.*lbf }

  1. A174749E01
    Attach the 3 wire harness clamps.

  1. w/o Viscous Heater:
    Connect the connector to the water temperature sensor.

  1. w/ Viscous Heater:
    Connect the 2 connectors to the water temperature sensor and viscous with magnet clutch heater.


94. TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE

  1. A177380
    Temporarily install the air cleaner hose to the intake air connector.


95. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A174698
    Connect the air cleaner cap to the air cleaner hose, and install the air cleaner cap with the 4 clamps.

  1. Connect the mass air flow meter connector and attach the wire harness clamp to the air cleaner cap.

  1. Attach the wire harness clamp.

  1. A177377
    Align the protrusion of air cleaner cap and concave portion of air cleaner hose.

  1. Tighten the 2 hose clamps.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


96. INSTALL SUB-BATTERY

97. INSTALL MAIN BATTERY

98. INSTALL NO. 3 ENGINE ROOM WIRE
  1. Install the No. 3 engine room wire to the main battery and sub-battery positive terminals with the 2 nuts.

    Torque:
    7.6 N*m{ 77 kgf*cm , 67 in.*lbf }

  1. Connect the No. 3 engine room wire with the 4 clamps.

    A174837


99. BLEED CLUTCH LINE

C172957
  1. Remove the release cylinder bleeder plug cap.

  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug while the pedal is depressed.

  1. When fluid no longer comes out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled from the clutch line.


100. CHECK FOR CLUTCH FLUID LEAK

101. BLEED AIR FROM FUEL SYSTEM

  1. A175110
    Using the hand pump mounted on the fuel filter cap, bleed air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. The maximum hand pump pumping speed is 2 strokes per second.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use and the engine cannot be started.

  1. Check if the engine starts.

    NOTICE:
    1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.


    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON (IG) and turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.*1

  1. A194065E19
    Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.

    A192848E04

    HINT:
    When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

  1. Clear the DTCs (Click here).

    HINT:
    It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.

  1. Repeat steps *1 to *3.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    OK:
    No DTCs are output.


102. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Connect the cables to the negative (-) main battery and sub-battery terminals.


103. ADD ENGINE COOLANT

  1. A179103
    Remove the engine air bleed cap.

  1. A185226
    Connect a clear hose to the engine air bleed pipe.

  1. A177426
    Using a wrench, remove the vent plug.

  1. A177425
    Fill the radiator with TOYOTA SLLC to the radiator reservoir filler neck.

    HINT:
    Pour TOYOTA SLLC until it spills out of the engine air bleed pipe.

    Standard Capacity (for Automatic Transmission):
    Item
    Specified Condition
    Front heater only
    14.8 liters (15.6 US qts, 13.0 Imp. qts)
    Front heater and rear heater
    17.6 liters (18.6 US qts, 15.5 Imp. qts)
    Front heater with viscous heater
    15.2 liters (16.1 US qts, 13.4 Imp. qts)
    Front heater and rear heater with viscous heater
    18.0 liters (19.0 US qts, 15.4 Imp. qts)

    Standard capacity (for Manual Transmission):
    15.4 liters (16.3 US qts, 13.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A177426
    Install the vent plug.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

    NOTICE:
    Do not tighten the plug to 5.0 N*m (51 kgf*cm, 44 in.*lbf) or more, as the plug will be damaged.

  1. A185226
    Disconnect the clear hose from the engine air bleed pipe.

  1. A179103
    Install the engine air bleed cap when coolant comes out.

  1. Install the radiator reservoir cap.

  1. Start the engine.

    NOTICE:
    Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

  1. Maintain an engine speed of 3000 rpm for approximately 10 minutes so that the thermostat opens and air bleeding is performed.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan

    NOTICE:
    1. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    2. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174740
    Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.


104. INSPECT FOR FUEL LEAK
  1. Perform Active Test.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Start the engine.

    4. Turn the intelligent tester ON.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    6. Perform the Active Test.

      Tester Display
      Test Detail
      Control Range
      Diagnostic Note
      Test the Fuel Leak
      Pressurizes fuel inside common rail and checks for fuel leaks
      Stop/Start
      1. The fuel inside the common rail is pressurized to the specified value and the engine speed increases to 2000 rpm when Start is selected.
      2. The above conditions are preserved while Start is selected.


105. INSPECT FOR OIL LEAK
  1. Perform Active Test.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Start the engine.

    4. Turn the intelligent tester ON.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    6. Perform the Active Test.

      Tester Display
      Test Detail
      Control Range
      Diagnostic Note
      Test the Fuel Leak
      Pressurizes fuel inside common rail and checks for fuel leaks
      Stop/Start
      1. The fuel inside the common rail is pressurized to the specified value and the engine speed increases to 2000 rpm when Start is selected.
      2. The above conditions are preserved while Start is selected.


106. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174739
    Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 17.8 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks.
    If no external leaks are found, check the cylinder block and cylinder head.


107. INSPECT FOR EXHAUST GAS LEAK

108. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    Standard: 
    Condenser Core Thickness
    Air Conditioning Type
    Cool Box
    Refrigerant Charging Amount
    22 mm (0.866 in.)
    w/o Rear Cooler
    w/ Cool Box
    870 +/-30 g (30.7 +/-1.1 oz.)
    w/o Cool Box
    870 +/-30 g (30.7 +/-1.1 oz.)
    w/ Rear Cooler
    w/ Cool Box
    1010 +/-30 g (35.6 +/-1.1 oz.)
    w/o Cool Box
    960 +/-30 g (33.9 +/-1.1 oz.)
    16 mm (0.630 in.)
    w/o Rear Cooler
    w/ Cool Box
    770 +/-30 g (27.2 +/-1.1 oz.)
    w/o Cool Box
    770 +/-30 g (27.2 +/-1.1 oz.)
    w/ Rear Cooler
    w/ Cool Box
    970 +/-30 g (34.2 +/-1.1 oz.)
    w/o Cool Box
    920 +/-30 g (32.5 +/-1.1 oz.)

    I037365E19

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    2. Approximately 200 g (7.05 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.


109. WARM UP ENGINE
  1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch is on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


110. CHECK FOR REFRIGERANT GAS LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).

  1. I042222E21
    Using a halogen leak detector, check the refrigerant line for leakage.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.


111. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E156191E01
    Push the ventilator louver in the direction indicated by the arrow in the illustration to attach the 17 claws and 2 clips and install the ventilator louver.


112. INSTALL HOOD TO COWL TOP SEAL

  1. E156189
    Attach the 12 clips and 4 clamps to install the hood to cowl top seal.

  1. E156188
    Install the washer hose.


113. INSTALL FRONT FENDER MAIN SEAL RH

HINT:
Use the same procedures described for the LH side.


114. INSTALL FRONT FENDER MAIN SEAL LH

  1. B181061
    Attach the 3 clips to install the fender main seal.


115. INSTALL FRONT WIPER ARM RH

  1. E156199E01
    Stop the wiper motor at the automatic stop position.

  1. Clean the wiper pivot serration with a wire brush.

  1. E157803E01
    Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

    Standard Measurement:
    Position
    Specified Condition
    B
    20.0 to 40.0 mm (0.787 to 1.57 in.)

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


116. INSTALL FRONT WIPER ARM LH

  1. E156199E01
    Stop the wiper motor at the automatic stop position.

  1. Clean the wiper pivot serration with a wire brush.

  1. E157802E01
    Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

    Standard Measurement:
    Position
    Specified Condition
    A
    16.8 to 36.8 mm (0.661 to 1.45 in.)

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.


117. INSTALL FRONT FENDER APRON SEAL REAR LH

  1. A177005
    Install the front fender apron seal rear LH with the 4 clips.


118. INSTALL FRONT FENDER APRON SEAL FRONT LH

  1. A176301
    w/o KDSS:
    Install the front fender apron seal front LH with the 4 clips.

  1. A177004
    w/ KDSS:
    Install the front fender apron seal front LH with the 3 clips.


119. INSTALL FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Install the front fender apron seal rear RH with the 4 clips.


120. INSTALL FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Install the front fender apron seal front RH with the 3 clips.


121. INSTALL OIL PAN PROTECTOR ASSEMBLY

C171483
  1. Install the oil pan protector with the 4 bolts.

    Torque:
    63 N*m{ 642 kgf*cm , 46 ft.*lbf }


122. INSTALL NO. 2 ENGINE UNDER COVER

  1. A178462
    Install the engine under cover with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


123. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Install the engine under cover with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


124. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. A174148
    Install the splash shield with the clip, and then install the 3 bolts and screw.


125. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
  1. Install the splash shield with the clip, and then install the 3 bolts and screw.


126. INSTALL HOOD SUB-ASSEMBLY
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Install the 2 hood supports with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. As much as possible avoid touching the stroke portions of the rod to prevent foreign matter from attaching to it. Be sure to hold the cylinders while servicing.
    2. Do not wear cotton gloves or other similar materials when handling the rod. Fibers may attach to the rod and result in gas leaks.
    3. Do not apply any load to the cylinders in the horizontal direction in order to prevent the rod from being deformed.
    4. Install the hood support while supporting the hood by hand.


127. ADJUST HOOD SUB-ASSEMBLY
  1. Adjust the hood (Click here).


128. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


129. INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

A174740
  1. Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
    If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant (SLLC)" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.

    NOTICE:
    Do not substitute plain water for engine coolant.


130. INSPECT ENGINE IDLE SPEED

NOTICE:
  1. Turn all the electrical systems and the A/C off.
  2. When checking the idle speed, move the shift lever to neutral.

HINT:
  1. For more information about the intelligent tester, refer to its operator's manual.
  2. If an intelligent tester is not available, use a tachometer tester probe as a substitute.

  1. When using the intelligent tester:

    1. Warm up the engine.

    2. Connect the intelligent tester to the DLC3.

    3. Enter the following menus:
      Powertrain / Engine / Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for help selecting the Data List.

    4. Inspect the engine idle speed.

      Standard Idle Speed:
      Item
      Specified Condition
      for Automatic Transmission
      550 to 650 rpm
      for Manual Transmission
      500 to 600 rpm

    5. Disconnect the intelligent tester from the DLC3.

  1. When not using the intelligent tester:

    1. Warm up and stop the engine.

    2. A167780E01
      Connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.
      SST
      09843-18030  

    3. Inspect the engine idle speed.

      Standard Idle Speed:
      Item
      Specified Condition
      for Automatic Transmission
      550 to 650 rpm
      for Manual Transmission
      500 to 600 rpm

    4. Disconnect the tester probe from terminal 9 (TAC) of the DLC3.


131. INSPECT MAXIMUM ENGINE SPEED
  1. Start the engine.

  1. Fully depress the accelerator pedal.

  1. Check the maximum engine speed.

    Maximum engine speed:
    4700 to 4900 rpm


132. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

  1. A174701
    Install the engine cover with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →