2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

NOTICE:
w/ DPF:
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor while the engine speed is approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.


2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)

5. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

  1. A174701
    Remove the 2 nuts and No. 1 engine cover.


6. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 7 clips and upper radiator support seal.


7. REMOVE MAIN BATTERY

8. REMOVE SUB-BATTERY

9. REMOVE FRONT WHEEL

10. REMOVE HOOD SUB-ASSEMBLY

  1. A174152
    Remove the 2 hood stay bolts. Then disconnect the 2 hood supports.

    NOTICE:
    1. Avoid touching the stroke portions of the rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinders while servicing.
    2. Do not wear cotton gloves or other similar materials when handling the rod. Fibers may attach to the rod and result in gas leaks.
    3. Do not apply any load to the cylinders in the horizontal direction in order to prevent the rod from being deformed.
    4. Remove the hood support while supporting the hood by hand.

  1. Remove the 4 bolts and hood.


11. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. A271735
    Remove the 3 bolts and screw.

  1. Loosen the clip and remove the front fender splash shield LH.


12. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Remove the 3 bolts and 2 screws.

  1. Loosen the clip and remove the front fender splash shield RH.


13. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover.


14. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


15. REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483
  1. Remove the 4 bolts and oil pan protector.


16. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator reservoir cap to drain the coolant in the radiator.

  1. Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

    A174741E01

  1. Tighten the radiator drain cock plug by hand.

  1. A177208
    Tighten the oil filter bracket drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


17. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A177219
    Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }


18. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
(Click here)

19. REMOVE NO. 3 ENGINE ROOM WIRE
  1. Disconnect the 4 wire harness clamps.

  1. Remove the 2 nuts and No. 3 engine room wire.

    A174837


20. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A174698
    Loosen the hose clamp.

  1. Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.

  1. Detach the 4 clamps and remove the air cleaner cap.


21. REMOVE AIR CLEANER FILTER ELEMENT

22. REMOVE AIR CLEANER CASE

  1. A174700
    Using a clip remover, detach the wire harness clamp.

  1. Remove the 3 bolts and air cleaner case.


23. REMOVE NO. 1 AIR CLEANER HOSE

  1. A174699
    Loosen the hose clamp and remove the No. 1 air cleaner hose.


24. REMOVE INTAKE AIR CONNECTOR

  1. A174749E04
    w/ Viscous Heater:
    Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.
    Text in Illustration 
    *A
    w/ Viscous Heater

  1. w/o Viscous Heater:
    Disconnect the connector from the water temperature sensor.

  1. Using a clip remover, detach the 3 wire harness clamps.

  1. A174710
    Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.


25. REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A177428
    Insert a screwdriver between the reservoir and oil reservoir bracket, push the claw, and then disconnect the reservoir by pulling it upwards.


26. REMOVE NO. 1 OIL RESERVOIR BRACKET

  1. A184319
    Remove the 2 bolts and bracket.


27. REMOVE RADIATOR RESERVOIR ASSEMBLY

  1. A174735
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and radiator reservoir.


28. REMOVE VANE PUMP ASSEMBLY
  1. w/ DPF: (Click here)
  2. w/o DPF: (Click here)

29. DISCONNECT NO. 1 RADIATOR HOSE

30. DISCONNECT NO. 2 RADIATOR HOSE

31. REMOVE V-RIBBED BELT (w/ Viscous Heater)

  1. A174847
    Loosen the lock nut and turn the bolt counterclockwise.

  1. Remove the V-ribbed belt.


32. REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)

  1. A177430
    Remove the bolt, cover, No. 1 idler pulley and collar.


33. REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)

  1. A177431
    Remove the nut and No. 3 idler pulley.


34. REMOVE V-RIBBED BELT

  1. A174849
    Using a wrench to the V-ribbed belt tensioner bracket, turn the wrench clockwise and remove the V-ribbed belt.


35. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Remove the 3 clips and front fender apron seal front RH.


36. REMOVE FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Remove the 4 clips and front fender apron seal rear RH.


37. REMOVE FRONT FENDER APRON SEAL FRONT LH

  1. A176301
    w/o KDSS:
    Remove the 4 clips and front fender apron seal front LH.

  1. A177004
    w/ KDSS:
    Remove the 3 clips and front fender apron seal front LH.


38. REMOVE FRONT FENDER APRON SEAL REAR LH

  1. A177005
    Remove the 4 clips and front fender apron seal rear LH.


39. REMOVE OIL COOLER TUBE (for Automatic Transmission)

  1. C167861
    Disconnect the inlet and outlet No. 1 oil cooler hose.

  1. C175574
    Disconnect the inlet No. 2 and No. 3 oil cooler hoses.

  1. C175575
    Disconnect the inlet No. 4 oil cooler hose.

  1. C167866
    Remove the 2 bolts and transmission oil cooler tube.


40. REMOVE FAN SHROUD WITH FAN

  1. A161930
    Loosen the 4 nuts holding the fluid coupling fan.

  1. A177427
    Remove the 2 bolts holding the fan shroud.

  1. A179253
    Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.


41. REMOVE FAN PULLEY

42. REMOVE FRONT BUMPER WINCH COVER (w/ Winch)

  1. B302213
    Detach the 2 claws.

  1. Detach the 3 guides and remove front bumper winch cover sub-assembly.


43. REMOVE RADIATOR GRILLE

  1. B302174E01
    Put protective tape around the radiator grille assembly.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille assembly.

  1. w/ Wide View Front Monitor System:

    1. Disconnect the connector.


44. REMOVE FRONT BUMPER COVER

HINT:
For the front bumper cover with garnish, use the procedure described below.

  1. Put protective tape around the front bumper cover.

    B302149E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B313279E01

    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. Detach the 10 claws and remove the front bumper cover.

    B302150

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Disconnect the No. 4 engine room wire connector and remove the front bumper cover.

  1. B181927
    w/ Headlight Cleaner System:
    Disconnect the headlight cleaner hose and remove the front bumper cover.


45. REMOVE TRANSMISSION OIL COOLER AIR DUCT (for Automatic Transmission)

  1. A278346
    Remove the 4 bolts and oil cooler air duct.


46. DISCONNECT RADIATOR SIDE DEFLECTOR RH (for Manual Transmission)

  1. A270013
    Using a clip remover, remove the 4 clips, and remove the side deflector.


47. DISCONNECT RADIATOR SIDE DEFLECTOR LH

  1. A270014
    Using a clip remover, remove the 4 clips, and remove the side deflector.


48. REMOVE RADIATOR ASSEMBLY

  1. A174155
    Remove the 4 bolts and radiator.


49. DISCONNECT FRONT DIFFERENTIAL BREATHER TUBE

A177338

50. DISCONNECT FUEL TUBE
  1. w/ DPF:
    Disconnect the 2 fuel tubes from the No. 1 and No. 3 fuel tube clamps.

  1. w/o DPF:
    Disconnect the 3 fuel tubes from the No. 1 and No. 3 fuel tube clamps.


51. REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

  1. A257026
    Loosen the No. 1 air hose clamp.

  1. Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

  1. A257028
    Remove the 3 nuts, bolt and No. 1 cool air inlet.

  1. Remove the gasket from the air tube RH.


52. REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

  1. A257027
    Loosen the No. 2 air hose clamp.

  1. A257029
    Remove the 3 nuts, bolt and No. 2 cool air inlet.

  1. Remove the gasket from the air tube LH.


53. DISCONNECT WATER HOSE SUB-ASSEMBLY

A174687E02
Text in Illustration 
*A
w/ Rear Heater
*B
w/o Rear Heater

54. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A174875
    Disconnect the wire harness clamp from the No. 2 engine oil level dipstick guide.

  1. A267228E01
    Disconnect the ventilation hose from the cylinder head cover RH.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the 2 bolts and No. 2 engine oil level dipstick guide.

  1. Remove the O-ring from the No. 2 engine oil level dipstick guide.


55. REMOVE AIR TUBE SUB-ASSEMBLY RH

  1. A174729
    Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


56. REMOVE DIESEL THROTTLE BODY ASSEMBLY RH

  1. A163132
    Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


57. DRAIN CLUTCH FLUID (for Manual Transmission)

58. REMOVE CLUTCH HOSE (for Manual Transmission)

  1. A177028
    Disconnect the 2 flexible hose tubes from the clutch hose with a 10 mm union nut wrench while holding the flexible hose with a wrench.

    NOTICE:
    1. Do not bend or damage the flexible hose tubes.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tubes from the connecting point.

  1. Remove the 2 clips.

  1. A183845
    Remove the bolt and clutch hose.


59. REMOVE AIR TUBE SUB-ASSEMBLY LH

  1. A174728
    Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


60. REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177030
    Using a 10 mm union nut wrench, disconnect the tube connector to flexible hose tube from the clutch tube to release cylinder 2 way.

    NOTICE:
    1. Do not bend or damage the flexible hose tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tube from the connecting point.

  1. A177031
    Remove the 2 bolts and tube connector to flexible hose tube.


61. REMOVE NO. 1 GAS FILTER

  1. A163347
    Disconnect the hose from the intake pipe.

  1. Remove the No. 1 gas filter.


62. REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

  1. A185151
    for Manual Transmission:

    1. Remove the bolt and disconnect the clutch tube to release cylinder 2 way from the No. 3 intercooler support bracket.

  1. A163348
    Remove the 2 bolts and No. 3 intercooler support bracket.


63. REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

  1. A163131
    Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


64. REMOVE NO. 1 AIR HOSE

  1. A177374
    Loosen the hose clamp and remove the No. 1 air hose.


65. REMOVE NO. 3 AIR TUBE

  1. A174751
    Disconnect the wire harness from the clamp.

  1. Remove the nut and ground wire.

  1. A174752
    Remove the bolt and disconnect the wire harness bracket.

  1. A174708
    Loosen the hose clamp and remove the bolt and No. 3 air tube.


66. REMOVE NO. 1 AIR TUBE ASSEMBLY

  1. A174709
    Remove the bolt and No. 1 air tube.

  1. Remove the O-ring.


67. REMOVE NO. 2 AIR HOSE

  1. A177375
    Loosen the hose clamp and remove the No. 2 air hose.


68. REMOVE NO. 4 AIR TUBE

  1. A174690
    Remove the bolt and disconnect the suction hose.

  1. A174706
    Loosen the hose clamp and remove the bolt and No. 4 air tube.


69. REMOVE NO. 2 AIR TUBE ASSEMBLY

  1. A174707
    Remove the bolt and No. 2 air tube.

  1. Remove the O-ring.


70. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174711
    Disconnect the ventilation hose from the oil separator.

  1. Loosen the hose clamp.

  1. Remove the bolt and No. 2 air cleaner pipe.


71. REMOVE NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

  1. E154190
    Remove the bolt and disconnect the discharge hose from the cooler compressor.

  1. Remove the O-ring from the discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.


72. REMOVE SUCTION HOSE SUB-ASSEMBLY

  1. E154191
    Remove the bolt and disconnect the suction hose from the cooler compressor.

  1. Remove the O-ring from the suction hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.


73. REMOVE COOLER COMPRESSOR ASSEMBLY

  1. A174754
    Disconnect the 4 connectors.

  1. Using a clip remover, detach the 3 wire harness clamps.

  1. E154192
    Remove the 4 bolts and cooler compressor.


74. REMOVE NO. 2 INTAKE AIR CONNECTOR PIPE

  1. A174712
    w/ Intercooler:
    Disconnect the vacuum hose.

  1. A174713
    Loosen the hose clamp, and remove the bolt and No. 2 intake air connector pipe.


75. REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

  1. A174689
    Remove the 4 bolts and disconnect the 4 water hose ends, and then remove the heater water pipe.


76. REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174714
    Loosen the hose clamp.

  1. Remove the bolt and No. 1 air cleaner pipe.


77. DISCONNECT FUEL HOSE

  1. A271646E01
    w/ DPF:
    Text in Illustration 
    *a
    for Fuel Filter with Heater
    *b
    for Fuel Filter without Heater

  1. A271648E01
    w/o DPF:
    Text in Illustration 
    *a
    for Fuel Filter with Heater
    *b
    for Fuel Filter without Heater


78. REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

  1. A174688
    Remove the 2 bolts and disconnect the 2 water hose ends, and then remove the No. 3 water by-pass pipe.


79. REMOVE NO. 4 WATER BY-PASS PIPE

  1. w/ EGR System:

    1. Remove the 2 bolts and nut.

      A267344E01

      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    2. w/ DPF:
      Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.

    3. w/o DPF:
      Disconnect the 4 water hose ends, and then remove the No. 4 water by-pass pipe.

  1. w/o EGR System:

    1. A174692
      Remove the 2 bolts and nut.

    2. Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.


80. DISCONNECT ENGINE WIRE

  1. LH Side:

    1. A267317E01
      w/ DPF:
      Disconnect the 7 connectors from the injector driver.
      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    2. w/o DPF:
      Disconnect the 4 connectors from the injector driver.

    3. Disconnect the 4 connectors and detach the wire harness holder from the relay block.

    4. Remove the bolt and disconnect the ground wire.

    5. Disconnect the wire harness from the wire harness clamp holder.

    6. A174743E01
      Remove the bolt and disconnect the ground wire from the body panel.

    7. Using a clip remover, detach the ground wire clamp labeled A from the relay block side.

    8. Disconnect the wire harness from the wire harness clamp holder labeled B.

    9. A174745
      Remove the nut and detach the generator positive (+) cable holder from the relay block.

    10. Disconnect the generator positive (+) cable from the 2 clamps.

    11. A174755
      Disconnect the 2 connectors.

    12. Using a clip remover, detach the 3 wire harness clamps.

    13. A174747E01
      for RHD:
      Disconnect the 4 connectors and detach the wire harness tab labeled A from the relay block.

    14. for RHD:
      Disconnect the ECM connector.

    15. for RHD:
      Disconnect the wire harness from the wire harness clamp holder.

    16. Disconnect the 8 connectors.

      A267318E01

      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    17. Remove the bolt and the engine wire harness bracket labeled B.

    18. Using a clip remover, detach the wire harness clamp labeled D.

    19. Remove the 2 bolts and disconnect the engine wire protector labeled A.

    20. for RHD:
      Disconnect the wire harness from the wire harness clamp holder labeled C.

  1. RH Side:

    1. A179104E01
      for LHD:
      Disconnect the 4 connectors, and detach the wire harness holder from the relay block labeled A.

    2. for LHD:
      Disconnect the ECM connector.

    3. for LHD:
      Disconnect the wire harness from the wire harness clamp holder.

    4. Disconnect the 7 connectors.

      A267319E01

      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    5. Using a clip remover, detach the wire harness clamp.

    6. Remove the 3 bolts and disconnect the engine wire protector labeled A.

    7. Remove the bolt and the wire harness bracket labeled B.

    8. Remove the screw grommet, nut and the glow plug wire harness labeled C.

    9. A267320E01
      for RHD:
      Disconnect the wire harness from the wire harness clamp holder.
      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    10. for RHD:
      Remove the bolt and wire harness clamp holder.

    11. A174760
      w/ Winch:
      Remove the bolt and disconnect the ground wire.

  1. Rear Side:

    1. A267321E01
      Using a clip remover, detach the wire harness clamp.
      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    2. Remove the 2 bolts and 2 ground wires labeled C.

    3. Remove the 2 bolts and disconnect the engine wire harness protector labeled B.

    4. w/ DPF:
      Disconnect the 3 connectors.

    5. w/o DPF:
      Disconnect the connector.

    6. Remove the screw grommet, nut and disconnect the glow plug wire harness labeled A.


81. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

NOTICE:
  1. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel pipe ends, cover the fuel pipe ends with plastic bags.
  2. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel supply pump hole, cover the hole with protective tape.

  1. A174693
    Disconnect the fuel hose from the No. 5 nozzle leakage pipe.

  1. Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the union bolt and gasket.

  1. Remove the bolt, nut and No. 2 fuel pipe.


82. REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes, cover the holes with protective tape.

  1. w/ EGR System:

    1. A185542
      Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the 2 nuts and 2 No. 2 injection pipe clamps.

    3. Remove the No. 6 injection pipe.

  1. w/o EGR System:

    1. A174695
      Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the nut and No. 2 injection pipe clamp.

    3. Remove the bolt and No. 6 injection pipe.


83. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)

  1. A270017
    Disconnect the 2 vacuum hoses.

  1. Remove the bolt and vacuum switching valve.


84. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)

  1. A270018
    Disconnect the 2 vacuum hoses.

  1. A270019
    Remove the 3 bolts and vacuum transmitting pipe.


85. REMOVE CYLINDER HEAD COVER SILENCER LH (w/ DPF)

  1. A270020
    Remove the 4 bolts and cylinder head cover silencer.


86. REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A267230
    Disconnect the fuel hose.

  1. Remove the fuel check valve, No. 4 nozzle leakage pipe and gasket.


87. REMOVE INJECTION PIPE LH

  1. A267231E01
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. A267232E01
    Using a union nut wrench, remove the 4 injection pipes.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


88. REMOVE NO. 2 FUEL PIPE (w/ DPF)

  1. A271233
    Remove the No. 4 fuel hose.

  1. Remove the union bolt, gasket, bolt, and No. 2 fuel pipe.


89. REMOVE NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. w/ DPF:

    1. Disconnect the fuel hose.

    2. A271234
      Remove the union bolt, gasket and No. 5 nozzle leakage pipe.

  1. A176403
    w/o DPF:
    Remove the union bolt, gasket and No. 5 nozzle leakage pipe.


90. REMOVE COMMON RAIL ASSEMBLY LH

  1. A271235E01
    Remove the 2 bolts and common rail.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    1. Do not remove the fuel pressure limiter from the common rail. If it is removed, replace the common rail.
    2. w/ DPF:
      Do not remove the pressure discharge valve from the common rail. If it is removed, replace the common rail.


91. REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

  1. w/ DPF:

    1. A267233
      Remove the bolt and No. 2 injection pipe clamp.

    2. Disconnect the fuel hose.

    3. Remove the union bolt, nut, bolt, fuel filter to injection pump fuel pipe and gasket.

  1. w/o DPF:

    1. A174697
      Disconnect the 2 hoses from the fuel pipe.

    2. Remove the bolt and fuel filter to injection pump fuel pipe.


92. DISCONNECT FUEL PUMP MOTOR WIRE

  1. A174792
    Remove the bolt and disconnect the connector from the fuel supply pump.


93. REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

  1. A174696
    Using a union nut wrench, remove the No. 5 injection pipe.

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail hole or injection pump hole, cover the holes with protective tape.


94. REMOVE CYLINDER HEAD COVER SILENCER RH (w/ DPF)

  1. A271208
    Remove the 4 bolts and cylinder head cover silencer.


95. REMOVE INJECTION PIPE RH

  1. A267234E01
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. A267235E01
    Using a union nut wrench, remove the 4 injection pipes.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


96. REMOVE COMMON RAIL ASSEMBLY RH

  1. A271236E01
    Remove the 2 bolts and common rail.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    Do not remove the fuel pressure sensor from the common rail. If it is removed, replace the common rail.


97. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174795

98. REMOVE NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174791

99. REMOVE CONNECTING WIRE (w/ DPF)

  1. A267236
    Detach the 2 clamps and remove the connecting wire.


100. REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A267237
    Remove the 2 injector hollow screws, 3 bolts, No. 3 nozzle leakage pipe and 2 gaskets.


101. REMOVE INTAKE PIPE

  1. A174796
    w/ EGR System:
    Remove the 2 nuts, 6 bolts, intake pipe and 2 gaskets.

  1. A180252
    w/o EGR System:
    Remove the 2 nuts, 4 bolts, intake pipe and gasket.


102. DISCONNECT NO. 2 ENGINE WIRE

  1. A174797
    Remove the 3 bolts and using a clip remover, detach the 2 wire harness clamps, and then disconnect the No. 2 engine wire.


103. REMOVE NO. 3 INTAKE MANIFOLD

  1. A174798
    Remove the 16 bolts, No. 3 intake manifold and 2 gaskets.


104. REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR System)

A174799

105. REMOVE EGR PIPE INSULATOR (w/ EGR System)

  1. A174800
    Remove the 2 bolts and EGR pipe insulator.


106. REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

  1. A267242
    Remove the 10 bolts, EGR valve with EGR cooler and 2 gaskets.

  1. A174802
    Disconnect the No. 5 water by-pass hose from the water by-pass outlet.


107. REMOVE EGR COOLER INSULATOR (w/ EGR System)

A174803

108. REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)

  1. A174804
    Disconnect the No. 1 fuel hose from the fuel cooler.

  1. Remove the union bolt, bolt, No. 3 nozzle leakage pipe and gasket.

    NOTICE:
    After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.


109. REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)

  1. A174805
    Disconnect the No. 2 fuel hose from the fuel cooler.

  1. Remove the union bolt, bolt, No. 4 nozzle leakage pipe and gasket.

    NOTICE:
    After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.


110. DISCONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)

A174806

111. REMOVE FUEL COOLER ASSEMBLY (w/o DPF)

  1. A176378
    Remove the 2 bolts and fuel cooler.


112. REMOVE NO. 2 FUEL INJECTOR PROTECTOR (w/ DPF)

  1. A271210
    Detach the hose clamp.

  1. Remove the bolt and No. 2 fuel injector protector.


113. REMOVE NO. 1 FUEL INJECTOR PROTECTOR (w/ DPF)

  1. A271209
    Remove the bolt and No. 1 fuel injector protector.


114. REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)

  1. A267238
    Disconnect the 3 fuel tube connectors (Click here).

  1. Detach the 3 clamps and remove the fuel tube.


115. REMOVE NO. 1 WATER BY-PASS PIPE

  1. A267239E01
    Remove the union bolt, bolt, No. 1 water by-pass pipe and gasket.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


116. REMOVE NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A271219
    Remove the 4 injector hollow screws and 4 gaskets.
    Text in Illustration 
    V100135
    Injector Hollow Screw
    V100136
    Bolt

  1. Remove the 2 bolts and No. 2 nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.


117. REMOVE NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A271214
    Remove the 4 injector hollow screws and 4 gaskets.
    Text in Illustration 
    V100135
    Injector Hollow Screw
    V100136
    No. 2 Check Valve
    V100137
    Union Bolt

  1. Remove the No. 2 check valve from the fuel tube and No. 1 nozzle leakage pipe.

  1. Remove the union bolt and No. 1 nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.


118. REMOVE FUEL HOSE BRACKET (w/ DPF)

  1. A267240
    Remove the bolt and fuel hose bracket.


119. REMOVE NO. 1 FUEL PIPE CLAMP (w/ DPF)

  1. A267241E01
    Remove the 2 bolts and 2 No. 1 fuel pipe clamps.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side


120. REMOVE NO. 1 INTAKE MANIFOLD

  1. A174809
    Remove the 9 bolts, No. 1 intake manifold and gasket.


121. REMOVE NO. 2 INTAKE MANIFOLD

  1. A174810
    Remove the 9 bolts, No. 2 intake manifold and gasket.


122. INSTALL NO. 1 AND NO. 2 ENGINE HANGER

  1. A181664E02
    Install the No. 1 and No. 2 engine hangers to the cylinder head RH and LH with the 4 bolts as shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    HINT:
    No. 1 engine hanger
    12281-51040
    No. 2 engine hanger
    12282-51040
    Bolt
    91671-80825

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger
    *a
    RH
    *b
    LH


123. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)

124. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY
(Click here)

125. REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177337
    Remove the bolt and clutch release cylinder to flexible hose tube.


126. REMOVE ENGINE ASSEMBLY

  1. A174842
    Attach an engine sling device and hang the engine with a chain block.

  1. Remove the 4 bolts from the engine mounting RH and LH side.

  1. Lift the engine out of the vehicle carefully.

    NOTICE:
    1. Make sure the engine is clear of all wiring and hoses.
    2. With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
    3. Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

  1. Place the engine onto a work bench.


127. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

C173317E01
  1. Put matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 8 set bolts, and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


128. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.


129. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. A185177
    Using a wrench, hold the crankshaft.

    NOTICE:
    Do not turn the crankshaft counterclockwise.
    If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (Click here).

    Torque:
    108 N*m{ 1101 kgf*cm , 80 ft.*lbf } or more

  1. A177363
    Remove the 8 bolts.

  1. A177364E01
    Remove the rear drive plate spacer labeled A, drive plate and ring gear labeled B and rear crankshaft balancer weight labeled C.


130. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A185177
    Using a wrench, hold the crankshaft.

    NOTICE:
    Do not turn the crankshaft counterclockwise.
    If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (Click here).

    Torque:
    108 N*m{ 1101 kgf*cm , 80 ft.*lbf } or more

  1. A177365
    Remove the 8 bolts and flywheel.


131. INSTALL ENGINE STAND
  1. Install the engine onto an engine stand with bolts.

  1. Remove the 4 bolts and No. 1 and No. 2 engine hangers.


132. REMOVE FRONT ENGINE MOUNTING INSULATOR RH

A176553
  1. Disconnect the vacuum hose.

  1. Remove the nut and mounting insulator.


133. REMOVE FRONT ENGINE MOUNTING INSULATOR LH

  1. A176552
    Remove the nut and mounting insulator.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →