2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail, cylinder head, or intake manifold, it is necessary to replace the injection pipes with new ones.
  2. w/ DPF:
    When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. A271735
    Remove the 3 bolts and screw.

  1. Loosen the clip and remove the front fender splash shield LH.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Remove the 3 bolts and 2 screws.

  1. Loosen the clip and remove the front fender splash shield RH.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover.


6. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 7 clips and upper radiator support seal.


7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator reservoir cap to drain the coolant in the radiator.

  1. Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

    A174741E01

  1. Tighten the radiator drain cock plug by hand.

  1. A177208
    Tighten the oil filter bracket drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


8. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
(Click here)

9. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A174698
    Loosen the hose clamp.

  1. Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.

  1. Detach the 4 clamps and remove the air cleaner cap.


10. REMOVE NO. 1 AIR CLEANER HOSE

  1. A174699
    Loosen the hose clamp and remove the No. 1 air cleaner hose.


11. REMOVE INTAKE AIR CONNECTOR

  1. A174749E04
    w/ Viscous Heater:
    Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.
    Text in Illustration 
    *A
    w/ Viscous Heater

  1. w/o Viscous Heater:
    Disconnect the connector from the water temperature sensor.

  1. Using a clip remover, detach the 3 wire harness clamps.

  1. A174710
    Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.


12. REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

  1. A257026
    Loosen the No. 1 air hose clamp.

  1. Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

  1. A257028
    Remove the 3 nuts, bolt and No. 1 cool air inlet.

  1. Remove the gasket from the air tube RH.


13. REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

  1. A257027
    Loosen the No. 2 air hose clamp.

  1. A257029
    Remove the 3 nuts, bolt and No. 2 cool air inlet.

  1. Remove the gasket from the air tube LH.


14. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A174875
    Disconnect the wire harness clamp from the No. 2 engine oil level dipstick guide.

  1. A267228E01
    Disconnect the ventilation hose from the cylinder head cover RH.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. Remove the 2 bolts and No. 2 engine oil level dipstick guide.

  1. Remove the O-ring from the No. 2 engine oil level dipstick guide.


15. REMOVE AIR TUBE SUB-ASSEMBLY RH

  1. A174729
    Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


16. REMOVE DIESEL THROTTLE BODY ASSEMBLY RH

  1. A163132
    Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


17. DRAIN CLUTCH FLUID (for Manual Transmission)

18. REMOVE CLUTCH HOSE (for Manual Transmission)

  1. A177028
    Disconnect the 2 flexible hose tubes from the clutch hose with a 10 mm union nut wrench while holding the flexible hose with a wrench.

    NOTICE:
    1. Do not bend or damage the flexible hose tubes.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tubes from the connecting point.

  1. Remove the 2 clips.

  1. A183845
    Remove the bolt and clutch hose.


19. REMOVE AIR TUBE SUB-ASSEMBLY LH

  1. A174728
    Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


20. REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

  1. A177030
    Using a 10 mm union nut wrench, disconnect the tube connector to flexible hose tube from the clutch tube to release cylinder 2 way.

    NOTICE:
    1. Do not bend or damage the flexible hose tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tube from the connecting point.

  1. A177031
    Remove the 2 bolts and tube connector to flexible hose tube.


21. REMOVE NO. 1 GAS FILTER

  1. A163347
    Disconnect the hose from the intake pipe.

  1. Remove the No. 1 gas filter.


22. REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

  1. A185151
    for Manual Transmission:

    1. Remove the bolt and disconnect the clutch tube to release cylinder 2 way from the No. 3 intercooler support bracket.

  1. A163348
    Remove the 2 bolts and No. 3 intercooler support bracket.


23. REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

  1. A163131
    Disconnect the throttle position sensor connector.

  1. Disconnect the throttle motor connector.

  1. Remove the 2 bolts, 2 nuts and throttle body.

  1. Remove the gasket from the intake pipe.


24. REMOVE NO. 1 AIR HOSE

  1. A177374
    Loosen the hose clamp and remove the No. 1 air hose.


25. REMOVE NO. 3 AIR TUBE

  1. A174751
    Disconnect the wire harness from the clamp.

  1. Remove the nut and ground wire.

  1. A174752
    Remove the bolt and disconnect the wire harness bracket.

  1. A174708
    Loosen the hose clamp and remove the bolt and No. 3 air tube.


26. REMOVE NO. 2 AIR HOSE

  1. A177375
    Loosen the hose clamp and remove the No. 2 air hose.


27. REMOVE NO. 4 AIR TUBE

  1. A174690
    Remove the bolt and disconnect the suction hose.

  1. A174706
    Loosen the hose clamp and remove the bolt and No. 4 air tube.


28. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174711
    Disconnect the ventilation hose from the oil separator.

  1. Loosen the hose clamp.

  1. Remove the bolt and No. 2 air cleaner pipe.


29. DISCONNECT WATER HOSE SUB-ASSEMBLY

A174687E02
Text in Illustration 
*A
w/ Rear Heater
*B
w/o Rear Heater

30. REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

  1. A174689
    Remove the 4 bolts and disconnect the 4 water hose ends, and then remove the heater water pipe.


31. REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

  1. A174714
    Loosen the hose clamp.

  1. Remove the bolt and No. 1 air cleaner pipe.


32. DISCONNECT FUEL HOSE

  1. A271646E01
    w/ DPF:
    Text in Illustration 
    *a
    for Fuel Filter with Heater
    *b
    for Fuel Filter without Heater

  1. A271648E01
    w/o DPF:
    Text in Illustration 
    *a
    for Fuel Filter with Heater
    *b
    for Fuel Filter without Heater


33. REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

  1. A174688
    Remove the 2 bolts and disconnect the 2 water hose ends, and then remove the No. 3 water by-pass pipe.


34. REMOVE NO. 4 WATER BY-PASS PIPE

  1. w/ EGR System:

    1. Remove the 2 bolts and nut.

      A267344E01

      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    2. w/ DPF:
      Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.

    3. w/o DPF:
      Disconnect the 4 water hose ends, and then remove the No. 4 water by-pass pipe.

  1. w/o EGR System:

    1. A174692
      Remove the 2 bolts and nut.

    2. Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.


35. DISCONNECT ENGINE WIRE

  1. LH Side:

    1. A174754
      Disconnect the 4 connectors.

    2. Using a clip remover, detach the 3 wire harness clamps.

    3. A174755
      Disconnect the 2 connectors.

    4. Using a clip remover, detach the 3 wire harness clamps.

    5. Disconnect the 8 connectors.

      A267318E01

      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    6. Remove the bolt and engine wire harness bracket labeled B.

    7. Using a clip remover, detach the wire harness clamp labeled D.

    8. Remove the 2 bolts and disconnect the engine wire protector labeled A.

    9. for RHD:
      Disconnect the wire harness from the wire harness clamp holder labeled C.

  1. RH Side:

    1. Disconnect the 7 connectors.

      A267319E01

      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    2. Using a clip remover, detach the wire harness clamp.

    3. Remove the 3 bolts and disconnect the wire harness protector labeled A.

    4. Remove the bolt and wire harness bracket labeled B.

    5. Remove the screw grommet, nut and glow plug wire harness labeled C.

    6. A267320E01
      for RHD:
      Disconnect the wire harness from the wire harness clamp holder.
      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    7. for RHD:
      Remove the bolt and wire harness clamp holder.

  1. Rear Side:

    1. A267321E01
      Using a clip remover, detach the wire harness clamp.
      Text in Illustration 
      *A
      w/ DPF
      *B
      w/o DPF

    2. Remove the 2 bolts and 2 ground wires labeled C.

    3. Remove the 2 bolts and disconnect the engine wire harness protector labeled B.

    4. w/ DPF:
      Disconnect the 3 connectors.

    5. w/o DPF:
      Disconnect the connector.

    6. Remove the screw grommet, nut and disconnect the glow plug wire harness labeled A.


36. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

NOTICE:
  1. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel pipe ends, cover the fuel pipe ends with plastic bags.
  2. After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel supply pump hole, cover the hole with protective tape.

  1. A174693
    Disconnect the fuel hose from the No. 5 nozzle leakage pipe.

  1. Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the union bolt and gasket.

  1. Remove the bolt, nut and No. 2 fuel pipe.


37. REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes, cover the holes with protective tape.

  1. w/ EGR System:

    1. A185542
      Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the 2 nuts and 2 No. 2 injection pipe clamps.

    3. Remove the No. 6 injection pipe.

  1. w/o EGR System:

    1. A174695
      Using a union nut wrench, loosen the No. 6 injection pipe ends.

    2. Remove the nut and No. 2 injection pipe clamp.

    3. Remove the bolt and No. 6 injection pipe.


38. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)

  1. A270017
    Disconnect the 2 vacuum hoses.

  1. Remove the bolt and vacuum switching valve.


39. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)

  1. A270018
    Disconnect the 2 vacuum hoses.

  1. A270019
    Remove the 3 bolts and vacuum transmitting pipe.


40. REMOVE CYLINDER HEAD COVER SILENCER LH (w/ DPF)

  1. A270020
    Remove the 4 bolts and cylinder head cover silencer.


41. REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A267230
    Disconnect the fuel hose.

  1. Remove the fuel check valve, No. 4 nozzle leakage pipe and gasket.


42. REMOVE INJECTION PIPE LH

  1. A267231E01
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. A267232E01
    Using a union nut wrench, remove the 4 injection pipes.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


43. REMOVE NO. 2 FUEL PIPE (w/ DPF)

  1. A271233
    Remove the No. 4 fuel hose.

  1. Remove the union bolt, gasket, bolt, and No. 2 fuel pipe.


44. REMOVE NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. w/ DPF:

    1. Disconnect the fuel hose.

    2. A271234
      Remove the union bolt, gasket and No. 5 nozzle leakage pipe.

  1. A176403
    w/o DPF:
    Remove the union bolt, gasket and No. 5 nozzle leakage pipe.


45. REMOVE COMMON RAIL ASSEMBLY LH

  1. A271235E01
    Remove the 2 bolts and common rail.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    1. Do not remove the fuel pressure limiter from the common rail. If it is removed, replace the common rail.
    2. w/ DPF:
      Do not remove the pressure discharge valve from the common rail. If it is removed, replace the common rail.


46. REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

  1. w/ DPF:

    1. A267233
      Remove the bolt and No. 2 injection pipe clamp.

    2. Disconnect the fuel hose.

    3. Remove the union bolt, nut, bolt, fuel filter to injection pump fuel pipe and gasket.

  1. w/o DPF:

    1. A174697
      Disconnect the 2 hoses from the fuel pipe.

    2. Remove the bolt and fuel filter to injection pump fuel pipe.


47. DISCONNECT FUEL PUMP MOTOR WIRE

  1. A174792
    Remove the bolt and disconnect the connector from the fuel supply pump.


48. REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

  1. A174696
    Using a union nut wrench, remove the No. 5 injection pipe.

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail hole or injection pump hole, cover the holes with protective tape.


49. REMOVE CYLINDER HEAD COVER SILENCER RH (w/ DPF)

  1. A271208
    Remove the 4 bolts and cylinder head cover silencer.


50. REMOVE NO. 2 FUEL INJECTOR PROTECTOR (w/ DPF)

  1. A271210
    Detach the hose clamp.

  1. Remove the bolt and No. 2 fuel injector protector.


51. REMOVE NO. 1 FUEL INJECTOR PROTECTOR (w/ DPF)

  1. A271209
    Remove the bolt and No. 1 fuel injector protector.


52. REMOVE INJECTION PIPE RH

  1. A267234E01
    w/ Intercooler:
    Remove the 2 nuts and 4 injection pipe clamps.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. A267235E01
    Using a union nut wrench, remove the 4 injection pipes.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.


53. REMOVE COMMON RAIL ASSEMBLY RH

  1. A271236E01
    Remove the 2 bolts and common rail.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    Do not remove the fuel pressure sensor from the common rail. If it is removed, replace the common rail.


54. REMOVE CONNECTING WIRE (w/ DPF)

  1. A267236
    Detach the 2 clamps and remove the connecting wire.


55. REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A267237
    Remove the 2 injector hollow screws, 3 bolts, No. 3 nozzle leakage pipe and 2 gaskets.


56. REMOVE NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A271219
    Remove the 4 injector hollow screws and 4 gaskets.
    Text in Illustration 
    V100135
    Injector Hollow Screw
    V100136
    Bolt

  1. Remove the 2 bolts and No. 2 nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.


57. REMOVE NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)

  1. A271214
    Remove the 4 injector hollow screws and 4 gaskets.
    Text in Illustration 
    V100135
    Injector Hollow Screw
    V100136
    No. 2 Check Valve
    V100137
    Union Bolt

  1. Remove the No. 2 check valve from the fuel tube and No. 1 nozzle leakage pipe.

  1. Remove the union bolt and No. 1 nozzle leakage pipe.

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.


58. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174795

59. REMOVE NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

A174791

60. REMOVE INTAKE PIPE

  1. A174796
    w/ EGR System:
    Remove the 2 nuts, 6 bolts, intake pipe and 2 gaskets.

  1. A180252
    w/o EGR System:
    Remove the 2 nuts, 4 bolts, intake pipe and gasket.


61. DISCONNECT NO. 2 ENGINE WIRE

  1. A174797
    Remove the 3 bolts and using a clip remover, detach the 2 wire harness clamps, and then disconnect the No. 2 engine wire.


62. REMOVE NO. 3 INTAKE MANIFOLD

  1. A174798
    Remove the 16 bolts, No. 3 intake manifold and 2 gaskets.


63. REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR System)

A174799

64. REMOVE EGR PIPE INSULATOR (w/ EGR System)

  1. A174800
    Remove the 2 bolts and EGR pipe insulator.


65. REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

  1. A267242
    Remove the 10 bolts, EGR valve with EGR cooler and 2 gaskets.

  1. A174802
    Disconnect the No. 5 water by-pass hose from the water by-pass outlet.


66. REMOVE EGR COOLER INSULATOR (w/ EGR System)

A174803

67. REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)

  1. A174804
    Disconnect the No. 1 fuel hose from the fuel cooler.

  1. Remove the union bolt, bolt, No. 3 nozzle leakage pipe and gasket.

    NOTICE:
    After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.


68. REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)

  1. A174805
    Disconnect the No. 2 fuel hose from the fuel cooler.

  1. Remove the union bolt, bolt, No. 4 nozzle leakage pipe and gasket.

    NOTICE:
    After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.


69. DISCONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)

A174806

70. REMOVE FUEL COOLER ASSEMBLY (w/o DPF)

  1. A176378
    Remove the 2 bolts and fuel cooler.


71. REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)

  1. A267238
    Disconnect the 3 fuel tube connectors (Click here).

  1. Detach the 3 clamps and remove the fuel tube.


72. REMOVE NO. 1 WATER BY-PASS PIPE

  1. A267239E01
    Remove the union bolt, bolt, No. 1 water by-pass pipe and gasket.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


73. REMOVE FUEL HOSE BRACKET (w/ DPF)

  1. A267240
    Remove the bolt and fuel hose bracket.


74. REMOVE NO. 1 FUEL PIPE CLAMP (w/ DPF)

  1. A267241E01
    Remove the 2 bolts and 2 No. 1 fuel pipe clamps.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side


75. REMOVE NO. 1 INTAKE MANIFOLD

  1. A174809
    Remove the 9 bolts, No. 1 intake manifold and gasket.


76. REMOVE NO. 2 INTAKE MANIFOLD

  1. A174810
    Remove the 9 bolts, No. 2 intake manifold and gasket.


77. REPLACE STUD BOLT

HINT:
If a stud bolt is deformed or its threads are damaged, replace it.

  1. A177310E02
    For Intake Pipe:
    Using an E8 "TORX" wrench, replace the stud bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. A177311E02
    For No. 3 Intake Manifold:

    1. Using an E8 "TORX" wrench, replace the stud bolts labeled A.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using an E6 "TORX" wrench, replace the stud bolts labeled B.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. Using an E6 "TORX" wrench, replace the stud bolt labeled C.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


78. REPLACE RING PIN

HINT:
It is not necessary to remove a ring pin unless it is being replaced.

  1. A177321E02
    For No. 1 and No. 2 Intake Manifold:
    Replace the ring pins.

    Standard protrusion:
    4.4 to 5.6 mm (0.173 to 0.222 in.)

    Text in Illustration 
    *1
    Protrusion height

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →