2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REASSEMBLY

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

NOTICE:
  1. Before performing these installation procedures, sufficiently clean and remove any foreign matter from the cylinder block, cylinder head, crankshaft, connecting rod, camshaft and other parts.
  2. When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.


1. SELECT NO. 2 CYLINDER HEAD GASKET
  1. Set the 2 crankshaft pulley set bolts to the crankshaft.

  1. Clean the cylinder block with solvent.

  1. Inspect the protrusion for each cylinder.

    1. Set the piston of the cylinder to be measured to slightly before TDC.

    2. A164862
      Place a dial indicator on the cylinder block, and set the measuring tip as shown in the illustration.

      NOTICE:
      Make sure that the dial indicator is at a right angle to the cylinder block top surface.

    3. Set the dial indicator at 0 mm (0 in.).

      HINT:
      Make sure that the measuring tip is flat against the cylinder block surface and piston head when taking the measurements.

    4. Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

    5. Measure the piston protrusion value of each cylinder at 2 places as shown in the illustration below, making a total of 8 measurements.

      Standard piston protrusion:
      0.520 to 0.780 mm (0.0205 to 0.0307 in.)

      If the protrusion is not as specified, remove and reinstall the piston and connecting rod.

      A182771E02
      Text in Illustration 
      *A
      for Bank 1
      *B
      for Bank 2
      *a
      Measuring Point
      -
      -
      V100136
      Front
      -
      -

  1. Select a new cylinder head gasket.

    A267348E01

    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2
    V100136
    Front
    -
    -

    HINT:
    Cylinder head gaskets are marked A, B, C, D or E accordingly.

    New Installed Cylinder Head Gasket Thickness:
    Item
    Cutout
    Specified Condition*
    A
    1
    1.20 to 1.30 mm (0.0472 to 0.0512 in.)
    B
    2
    1.25 to 1.35 mm (0.0492 to 0.0394 in.)
    C
    3
    1.30 to 1.40 mm (0.0512 to 0.0551 in.)
    D
    4
    1.35 to 1.45 mm (0.0531 to 0.0571 in.)
    E
    5
    1.40 to 1.50 mm (0.0551 to 0.0591 in.)

    HINT:
    *: The specified condition indicates the thickness of the gasket after tightening the cylinder head.


    1. Select the largest piston protrusion value from the measurements and then select a new appropriate gasket according to the table below.

      Standard Piston Protrusion:
      Item
      Specified Condition
      A
      0.520 to 0.575 mm (0.0205 to 0.0226 in.)
      B
      0.575 to 0.625 mm (0.0226 to 0.0246 in.)
      C
      0.625 to 0.675 mm (0.0246 to 0.0266 in.)
      D
      0.675 to 0.725 mm (0.0266 to 0.0285 in.)
      E
      0.725 to 0.780 mm (0.0285 to 0.0307 in.)


2. INSTALL NO. 2 CYLINDER HEAD GASKET

  1. A164880E02
    Remove any oil from the contact surface.
    Text in Illustration 
    *a
    Front
    *b
    Exhaust Side

  1. Place the cylinder head gasket on the cylinder block surface with the front face of the indicated mark "L" upward and facing the exhaust side.


3. INSTALL CYLINDER HEAD SUB-ASSEMBLY LH
  1. Place the cylinder head on the cylinder head gasket.

    NOTICE:
    Ensure that no oil is on the mounting surface of the cylinder head.

  1. Inspect the cylinder head bolts (Click here).

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1:

    1. A164541E02
      Install and uniformly tighten the 10 cylinder head bolts with the spacers in several steps, in the sequence shown in the illustration.

      Torque:
      80 N*m{ 816 kgf*cm , 59 ft.*lbf }

      HINT:
      1. The cylinder head bolts are tightened in 4 progressive steps.
      2. If a cylinder head bolt is broken or deformed, replace it.

  1. A158686E04
    Step 2:

    1. Mark the cylinder head bolt heads with paint as shown in the illustration.

      Text in Illustration 
      *1
      Painted Mark
      V100136
      Front

    2. Tighten the cylinder head bolts 90° in the sequence shown in step 1.

  1. A158687E03
    Step 3:

    1. Tighten the cylinder head bolts another 90° in the sequence shown in step 1.

      Text in Illustration 
      *1
      Painted Mark
      V100136
      Front

  1. A164864E03
    Step 4:

    1. Tighten the cylinder head bolts by an additional 90° in the sequence shown in step 1.

      Text in Illustration 
      *1
      Painted Mark
      V100136
      Front

  1. Check that the painted marks are now facing the exhaust port side.


4. INSTALL NO. 2 VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
Be sure to inspect the valve lash adjuster before installing it (Click here).

  1. Install the 16 No. 2 valve lash adjusters to the cylinder head.

    HINT:
    Install the lash adjuster at the same place it was removed from.


5. INSTALL NO. 2 VALVE ROCKER ARM

  1. A181682
    Apply engine oil to the lash adjuster tips and valve stem ends.

  1. Install the 16 No. 2 valve rocker arms as shown in the illustration.

    HINT:
    A164641
    Install the valve rocker arm at the same place it was removed from.


6. INSTALL NO. 5 CAMSHAFT BEARING CAP
  1. Align the camshaft bearing cap and the ring pins of the cylinder head, and install the cap.


7. SELECT NO. 1 CYLINDER HEAD GASKET
  1. Set the 2 crankshaft pulley set bolts to the crankshaft.

  1. Clean the cylinder block with solvent.

  1. Inspect the protrusion for each cylinder.

    1. Set the piston of the cylinder to be measured to slightly before TDC.

    2. A164862
      Place a dial indicator on the cylinder block, and set the measuring tip as shown in the illustration.

      NOTICE:
      Make sure that the dial indicator is at a right angle to the cylinder block top surface.

    3. Set the dial indicator at 0 mm (0 in.).

      HINT:
      Make sure that the measuring tip is flat against the cylinder block surface and piston head when taking the measurements.

    4. Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

    5. Measure the piston protrusion value of each cylinder at 2 places as shown in the illustration below, making a total of 8 measurements.

      Standard piston protrusion:
      0.520 to 0.780 mm (0.0205 to 0.0307 in.)

      If the protrusion is not as specified, remove and reinstall the piston and connecting rod.

      A182771E02
      Text in Illustration 
      *A
      for Bank 1
      *B
      for Bank 2
      *a
      Measuring Point
      -
      -
      V100136
      Front
      -
      -

  1. Select a new cylinder head gasket.

    A267348E01

    Text in Illustration 
    *A
    for Bank 1
    *B
    for Bank 2
    V100136
    Front
    -
    -

    HINT:
    Cylinder head gaskets are marked A, B, C, D or E accordingly.

    New Installed Cylinder Head Gasket Thickness:
    Item
    Cutout
    Specified Condition*
    A
    1
    1.20 to 1.30 mm (0.0472 to 0.0512 in.)
    B
    2
    1.25 to 1.35 mm (0.0492 to 0.0394 in.)
    C
    3
    1.30 to 1.40 mm (0.0512 to 0.0551 in.)
    D
    4
    1.35 to 1.45 mm (0.0531 to 0.0571 in.)
    E
    5
    1.40 to 1.50 mm (0.0551 to 0.0591 in.)

    HINT:
    *: The specified condition indicates the thickness of the gasket after tightening the cylinder head.


    1. Select the largest piston protrusion value from the measurements and then select a new appropriate gasket according to the table below.

      Standard Piston Protrusion:
      Item
      Specified Condition
      A
      0.520 to 0.575 mm (0.0205 to 0.0226 in.)
      B
      0.575 to 0.625 mm (0.0226 to 0.0246 in.)
      C
      0.625 to 0.675 mm (0.0246 to 0.0266 in.)
      D
      0.675 to 0.725 mm (0.0266 to 0.0285 in.)
      E
      0.725 to 0.780 mm (0.0285 to 0.0307 in.)


8. INSTALL NO. 1 CYLINDER HEAD GASKET

  1. A164879E02
    Remove any oil from the contact surface.
    Text in Illustration 
    *a
    Front
    *b
    Exhaust Side

  1. Place the cylinder head gasket on the cylinder block surface with the front face of the indicated mark "R" upward and facing the exhaust side.


9. INSTALL CYLINDER HEAD SUB-ASSEMBLY RH
  1. Place the cylinder head on the cylinder head gasket.

    NOTICE:
    Ensure that no oil is on the mounting surface of the cylinder head.

  1. Inspect the cylinder head bolts (Click here).

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1:

    1. A164533E02
      Install and uniformly tighten the 10 cylinder head bolts with the spacers in several steps, in the sequence shown in the illustration.

      Torque:
      80 N*m{ 816 kgf*cm , 59 ft.*lbf }

      HINT:
      1. The cylinder head bolts are tightened in 4 progressive steps.
      2. If a cylinder head bolt is broken or deformed, replace it.

  1. A158686E04
    Step 2:

    1. Mark the cylinder head bolt heads with paint as shown in the illustration.

      Text in Illustration 
      *1
      Painted Mark
      V100136
      Front

    2. Tighten the cylinder head bolts 90° in the sequence shown in step 1.

  1. A158687E03
    Step 3:

    1. Tighten the cylinder head bolts another 90° in the sequence shown in step 1.

      Text in Illustration 
      *1
      Painted Mark
      V100136
      Front

  1. A164864E03
    Step 4:

    1. Tighten the cylinder head bolts by an additional 90° in the sequence shown in step 1.

      Text in Illustration 
      *1
      Painted Mark
      V100136
      Front

  1. Check that the painted marks are now facing the intake port side.


10. INSTALL NO. 1 VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
Be sure to inspect the valve lash adjuster before installing it (Click here).

  1. Install the 16 No. 1 valve lash adjusters to the cylinder head.

    HINT:
    Install the lash adjuster at the same place it was removed from.


11. INSTALL NO. 1 VALVE ROCKER ARM

  1. A181682
    Apply engine oil to the lash adjuster tips and valve stem ends.

  1. Install the 16 No. 1 valve rocker arms as shown in the illustration.

    HINT:
    A164641
    Install the valve rocker arm at the same place it was removed from.


12. INSTALL NO. 2 CAMSHAFT BEARING CAP
  1. Align the camshaft bearing cap and the ring pins of the cylinder head, and install the cap.


13. SET NO. 1 CYLINDER TO 45° BEFORE TDC

  1. A164515
    Using a bar, turn the crankshaft counterclockwise until the No. 1 cylinder is at a position 45° before TDC.

    NOTICE:
    Do not turn the crankshaft again until after the timing gear is installed.

    HINT:
    The No. 1 cylinder is at a position 45° before TDC if the crankshaft counterweight is overlapping the cylinder block hole as shown in the illustration.

  1. Remove the 2 crankshaft pulley set bolts.


14. INSTALL NO. 1 AND NO. 2 CAMSHAFTS

  1. A164904
    Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.

  1. A164816
    Apply engine oil to the rollers of the valve rocker arms and the camshaft housing of the cylinder head.

  1. A164519
    Install the camshafts.

    1. Apply engine oil to the camshaft journals, lobes, thrust portion and gears.

    2. Align the timing marks (2 dot marks) on the back side of the No. 1 and No. 2 camshaft timing gears as shown in the illustration.

    3. Place the camshafts into the cylinder head.

      NOTICE:
      A164641
      Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.

  1. A164791
    Install the No. 1 camshaft bearing cap.

    1. Align the No. 1 camshaft bearing cap and the ring pins of the No. 2 camshaft bearing cap.

    2. Temporarily install the 4 bolts by hand.

  1. A164527
    Install the No. 3 camshaft bearing caps.

    1. Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.

    2. Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.

  1. A164792
    Temporarily install the No. 1 and No. 2 camshaft oil feed pipes with the 8 bolts by hand.

    NOTICE:
    If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.

    HINT:
    The pipe is bent on the intake side, and straight on the exhaust side.

  1. A164793
    Temporarily install the 2 union bolts by hand.

  1. A181660E02
    Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

    Torque:
    for 12 mm head bolt of No. 1 camshaft bearing cap:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for 10 mm head bolt of No. 3 camshaft bearing cap:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    12 mm Head Bolt
    *2
    10 mm Head Bolt

  1. A164793
    Tighten the 2 union bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. A164905
    Remove the service bolt from the No. 1 camshaft timing gear.

    NOTICE:
    Do not drop the bolt into the engine.


15. INSTALL NO. 3 AND NO. 4 CAMSHAFTS

  1. A164904
    Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.

  1. A164816
    Apply engine oil to the rollers of the valve rocker arms and camshaft housing of the cylinder head.

  1. A164520
    Install the camshafts.

    1. Apply engine oil to the camshaft journals, lobes, thrust portion and gears.

    2. Align the timing marks (1 dot mark) on the back side of the No. 3 and No. 4 camshaft timing gears as shown in the illustration.

    3. Place the camshafts into the cylinder head.

      NOTICE:
      A164641
      Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.

  1. A164794
    Install the No. 4 camshaft bearing cap.

    1. Align the No. 4 camshaft bearing cap and the ring pins of the No. 5 camshaft bearing cap.

    2. Temporarily install the 4 bolts by hand.

  1. A164536
    Install the No. 3 camshaft bearing caps.

    1. Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.

    2. Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.

  1. A164795
    Temporarily install the No. 3 and No. 4 camshaft oil feed pipes with the 8 bolts by hand.

    NOTICE:
    If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.

    HINT:
    The pipe is bent on the intake side, and straight on the exhaust side.

  1. A164783
    Temporarily install the 2 union bolts by hand.

  1. A181662E02
    Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

    Torque:
    for 12 mm head bolt of No. 4 camshaft bearing cap:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for 10 mm head bolt of No. 3 camshaft bearing cap:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    12 mm Head Bolt
    *2
    10 mm Head Bolt

  1. A164783
    Tighten the 2 union bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. A164905
    Remove the service bolt from the No. 4 camshaft timing gear.

    NOTICE:
    Do not drop the bolt into the engine.


16. INSTALL NO. 2 TIMING GEAR CASE INSULATOR (w/ Intercooler)

17. INSTALL NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)
  1. Install the No. 2 vacuum transmitting pipe with the 3 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


18. INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)
  1. Install the No. 1 vacuum transmitting pipe with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


19. CONNECT NO. 3 VACUUM TRANSMITTING HOSE (w/ Intercooler)

20. CONNECT NO. 2 VACUUM TRANSMITTING HOSE (w/ Intercooler)

21. INSTALL TIMING GEAR CASE SUB-ASSEMBLY

NOTICE:
When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.
A158670E02

Text in Illustration 
*a
Cylinder Block
*b
Timing Gear Case

  1. Apply seal packing to the timing gear case as shown in the following illustration.

    Standard seal diameter:
    4 to 5 mm (0.157 to 0.197 in.)

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. After applying seal packing, align the timing gear case with the engine within 3 minutes and tighten the bolts and nuts within 15 minutes.
    2. Apply the seal packing in a continuous line.

    HINT:
    1. The FIPG line is shown below.
    2. Apply packing to the 5 seal surface areas.


    A158675E03
    Text in Illustration 
    *a
    Seal Diameter: 4 to 5 mm
    -
    -

  1. A181226E02
    Install a new timing gear case gasket.
    Text in Illustration 
    *1
    New Timing Gear Case Gasket
    *2
    New O-Ring

  1. Apply engine oil to 2 new O-rings and install them to the timing gear case.

  1. A164512E03
    Install the timing gear case with the 22 bolts and 2 nuts.

    Torque:
    for 14 mm head bolt (When "dry"):
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }
    for 14 mm head bolt (When "wet"):
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }
    for 12 mm head bolt A and B:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for nut:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    Text in Illustration 
    *1
    Nut
    *2
    14 mm Head Bolt
    *3
    12 mm Head Bolt A
    *4
    12 mm Head Bolt B

    NOTICE:
    1. The case is "dry" when there is absolutely no engine oil on the 14 mm head bolts and cylinder head bolt holes.
    2. The case is "wet" when there is engine oil on the 14 mm head bolts and cylinder head bolt holes.

    Bolt Length 
    Item
    Quantity
    Length
    A
    4
    20 mm (0.787 in.)
    B
    8
    45 mm (1.77 in.)


22. INSTALL V-BANK SILENCER
  1. Align the alignment areas of the V-bank silencer and cylinder block, and install the V-bank silencer.

    NOTICE:
    Verify that the V-bank silencer is below the top surface of the intake port of the cylinder head RH and LH.


23. INSTALL FUEL SUPPLY PUMP ASSEMBLY

  1. A164817
    Using an 8 mm x 1.25 pitch tap, remove the adhesive from the timing gear case side bolt hole.

  1. A164818E02
    Apply adhesive to 2 or more threads of the timing gear case bolt hole.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Text in Illustration 
    *1
    Adhesive

  1. A164821E02
    Apply engine oil to a new O-ring and install it to the supply pump.
    Text in Illustration 
    *1
    New O-Ring

  1. Install the supply pump to the timing gear case.

    NOTICE:
    When installing the supply pump, do not hold the fuel pipe to prevent fuel leaks.


    1. Temporarily install the 2 nuts.

    2. Using a 6 mm hexagon wrench, install the hexagon bolt, and then tighten the 2 nuts.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }


24. INSTALL STRAIGHT PIN
  1. Install the straight pin.

    Standard protrusion height:
    4.5 to 7.0 mm (0.177 to 0.276 in.)


25. ASSEMBLE FUEL SUPPLY PUMP DRIVE GEAR AND FUEL SUPPLY PUMP SHAFT SPROCKET
  1. Align the fuel supply pump drive gear to the fuel supply pump shaft sprocket straight pin and temporarily install it with the 4 bolts.

  1. Hold the fuel supply pump shaft sprocket in a vise between aluminum plates.

    NOTICE:
    Be careful not to damage the gears.

  1. Tighten the 4 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


26. INSTALL RADIAL BALL BEARING

  1. A158681E02
    Using SST and a press, press in the radial ball bearing to the fuel supply pump shaft sprocket.
    SST
    09316-12010  
    09950-60010   (09951-00580)
    Text in Illustration 
    *1
    Radial Ball Bearing
    *2
    Fuel Supply Pump Shaft Sprocket

    NOTICE:
    1. Make sure to press in the bearing until the bearing contacts the fuel supply pump shaft sprocket, as shown in A in the illustration.
    2. Make sure the sprocket outer edge is further outward than the bearing outer edge, as shown in B in the illustration.


27. TEMPORARILY INSTALL FUEL SUPPLY PUMP DRIVE GEAR

  1. A164525
    Align the cutout of the supply pump drive gear and key of the supply pump, and temporarily install the fuel supply pump drive gear nut.


28. SET NO. 1 AND NO. 2 CAMSHAFTS TO TDC

  1. A164516
    Using a wrench, turn the No. 1 camshaft and align the timing marks (1 dot mark) on the back side of the timing gears as shown in the illustration.


29. INSTALL NO. 1 IDLE GEAR SHAFT

  1. A164840
    Apply engine oil to the contact surface of the idle gear shaft and the back side of the protrusion.

  1. Install the idle gear shaft to the cylinder block.


30. ASSEMBLE SUB GEAR, IDLE GEAR SPRING AND IDLE GEAR (w/ Intercooler)

  1. A180311
    Hold the idle gear in a vise between aluminum plates.

    NOTICE:
    Be careful not to damage the gears.

  1. A180312
    Align the right end of the idle gear spring to the notch of the idle gear and set it to the gear.

  1. A177422
    Install the sub idle gear.

    1. Align the notch of the sub idle gear protrusion with the left end of the idle gear spring and install the sub idle gear to the idle gear.

    2. A177423E02
      Using SST, turn the sub idle gear counterclockwise, and install an 8 mm x 1.25 pitch bolt with a length of 15 mm or more to the service hole.
      SST
      09960-10010   (09962-01000, 09963-00700)

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

      Text in Illustration 
      *1
      Service Bolt


31. INSTALL IDLE GEAR ASSEMBLY

  1. A170353E02
    Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.
    Text in Illustration 
    *1
    Key

  1. Using a bar, turn the crankshaft clockwise to the No. 1 cylinder TDC position.

  1. Align the timing marks of the supply pump drive gear and idle gear, and the timing marks of the crankshaft timing gear and idle gear as shown in the illustration.

    A257019E02

    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler

  1. Apply engine oil to the idle gear thrust plate and gears.

  1. Install the idle gear thrust plate with the 2 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }

  1. w/ Intercooler:
    Remove the service bolt.


32. TIGHTEN FUEL SUPPLY PUMP DRIVE GEAR NUT

  1. Using SST, hold the idle gear and tighten the nut.

    SST
    09960-10010   (09962-01000, 09963-00700)

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }


    A257020E02
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler


33. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

  1. Check that the timing marks of the following pairs of parts are aligned: 1) supply pump drive gear and idle gear: 2) crankshaft timing gear and idle gear: 3) RH and LH camshaft timing gears.

    A177357


34. INSTALL NO. 2 CAMSHAFT TIMING SPROCKET AND NO. 2 TIMING CHAIN

  1. A164523
    Align the 2 mark plates (yellow) on the No. 2 timing chain with the timing mark (1 dot mark) of the No. 2 camshaft timing sprocket as shown in the illustration.

  1. A174774E02
    Align the No. 2 timing chain mark plate (yellow) with the supply pump drive gear timing mark, and temporarily install the No. 2 camshaft timing sprocket with the 4 bolts.
    Text in Illustration 
    *1
    Timing Mark

  1. A164506E01
    Using SST, hold the No. 2 camshaft timing sprocket, and tighten the 4 bolts.
    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


35. INSTALL NO. 1 CAMSHAFT TIMING SPROCKET AND NO. 1 TIMING CHAIN

  1. A164521
    Align the 2 mark plates (yellow) on the No. 1 timing chain with the timing mark (1 dot mark) of the No. 1 camshaft timing sprocket as shown in the illustration.

  1. A174775E02
    Align the No. 1 timing chain mark plate (yellow) with the supply pump drive gear timing mark, and temporarily install the No. 1 camshaft timing sprocket.
    Text in Illustration 
    *1
    Timing Mark


36. INSTALL PUMP DRIVE SHAFT GEAR

  1. A164498E01
    Temporarily install the pump drive shaft gear with the 4 bolts.

  1. Using SST, hold the pump drive shaft gear and tighten the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


37. INSTALL NO. 2 CHAIN VIBRATION DAMPER
  1. Install the No. 2 chain vibration damper with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


38. INSTALL NO. 2 CHAIN TENSIONER SLIPPER

39. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A164589
    Move the stopper plate clockwise to release the lock, and push the plunger into the tensioner.

  1. Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.

  1. Install the No. 2 chain tensioner with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the hexagon wrench.


40. INSTALL NO. 1 CHAIN VIBRATION DAMPER
  1. Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


41. INSTALL NO. 1 CHAIN TENSIONER SLIPPER

42. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A164589
    Move the stopper plate clockwise to release the lock, and push the plunger into the tensioner.

  1. Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.

  1. Install the No. 1 chain tensioner with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the hexagon wrench.


43. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Remove the adhesive from the threads of the 2 screws and the bolt holes of the crankshaft.

  1. A164913E01
    Apply adhesive to 2 or 3 threads of the 2 screws.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Text in Illustration 
    *1
    Adhesive

  1. Using a T30 "TORX" wrench, install the No. 1 crankshaft position sensor plate with the 2 screws.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure the "F" mark on the plate is facing towards the front side of the engine.

    HINT:
    When replacing the No. 1 crankshaft position sensor plate, perform "Crank Time Compensation Reset" (Click here).


44. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.

  1. Rotate the crankshaft 2 revolutions or more so that the crankshaft key is 45° counterclockwise from the top. Check that the timing marks (1 dot mark each) of the RH and LH camshaft timing gears align. If not as specified, turn the crankshaft 1 revolution (360°) and align the timing marks. If the timing marks are deviated, reinstall the chain and camshaft.

    A174764E03

    Text in Illustration 
    *1
    Key
    -
    -
    *a
    Top
    -
    -

  1. Remove the 2 crankshaft pulley set bolts.


45. INSTALL FRONT CRANKSHAFT OIL SEAL

  1. A164640E01
    Place the timing chain cover on wooden blocks.

  1. Using SST and a hammer, tap in a new oil seal as shown in the illustration.

    SST
    09316-12010  
    09950-70010   (09951-07100)
    09950-60020   (09951-00890)

    Standard depth A:
    0.6 to 1.4 mm (0.0236 to 0.0551 in.)


46. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

NOTICE:
When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.
A158671E02

Text in Illustration 
*1
Timing Gear Case
*2
Timing Chain Cover

  1. A174785E02
    Install a new O-ring to the timing gear case.
    Text in Illustration 
    *1
    New O-Ring

  1. Apply seal packing to the timing chain cover as shown in the following illustration.

    Standard seal diameter:
    4 to 5 mm (0.157 to 0.197 in.)

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. After applying seal packing, align the timing chain cover with the timing gear case within 3 minutes and tighten the bolts and nuts within 15 minutes.
    2. Apply the seal packing in a continuous line.
    3. Make sure the seal packing does not become thinner than 4 mm (0.157 in.) at the areas labeled "B" in the illustration below.


    HINT:
    1. The FIPG line is shown below.
    2. Apply packing to the 6 seal surface areas.
    A158676E03

    Text in Illustration 
    *a
    Seal Diameter: 4 to 5 mm
    -
    -

  1. Apply engine oil to the lip of the oil seal.

  1. Align and install the timing chain cover to the timing gear case knock pin and supply pump bearing.

    NOTICE:
    Make sure that the lip of the oil seal is properly installed.

  1. A168359E02
    If the stud bolts are loose, tighten them using an E7 "TORX" wrench.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    Text in Illustration 
    *1
    Stud Bolt

  1. A177358E02
    Install and uniformly tighten the 16 bolts and 4 nuts in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *1
    Nut


47. INSTALL TIMING CHAIN COVER PLATE
  1. Install a new gasket and the cover plate with the 4 bolts.

    Torque:
    9.1 N*m{ 93 kgf*cm , 81 in.*lbf }


48. INSTALL WATER PUMP ASSEMBLY

  1. A174821E01
    Temporarily install a new gasket and the water pump with the 9 bolts and 2 nuts.
    Bolt Length 
    Item
    Length
    Bolt A
    30 mm (1.18 in.)
    Bolt B
    80 mm (3.15 in.)

  1. A174821E02
    Uniformly tighten the 9 bolts and 2 nuts of the water pump in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    After installing all of the bolts and nuts, check that all of the bolts and nuts are tightened to the torque specification.


49. TEMPORARILY INSTALL INTAKE MANIFOLD

  1. A177324
    Install the gasket and temporarily install the No. 2 intake manifold with the 9 bolts.

  1. A177323
    Install the gasket and temporarily install the No. 1 intake manifold with the 9 bolts.

  1. A174867E01
    Install the 2 gaskets and temporarily install the No. 3 intake manifold with the 16 bolts.
    Bolt Length 
    Item
    Length
    Bolt A
    25 mm (0.984 in.)
    Bolt B
    70 mm (2.76 in.)


50. INSTALL FUEL INJECTOR LH (w/o DPF)

NOTICE:
Be sure to install the injector, holder clamp and bolt in their original positions.

  1. A164163
    Install 4 new injection nozzle seats to the cylinder head.

  1. Apply a light coat of clean engine oil to 4 new O-rings.

  1. A164164E03
    Install an O-ring to each injector as shown in the illustration.
    Text in Illustration 
    *1
    New O-Ring

  1. Insert the 4 injectors into the cylinder head.

    NOTICE:
    1. Insert the injector until it touches the nozzle seat surface.
    2. After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.
    3. Always return an injector to the same place it was removed from.

  1. For an injector that has been replaced with a new injector, register the injector compensation code (Click here).

  1. A164160E06
    Temporarily install 4 new washers and the 4 nozzle clamps with the 4 clamp bolts.
    Text in Illustration 
    *1
    New Washer
    *2
    Nozzle Holder Clamp
    *a
    Downward

    NOTICE:
    1. The fork portion of the nozzle holder clamp must be set to the injector.
    2. Before tightening the bolts, check that the nozzle holder clamps are set properly.
    3. To tighten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.
    4. When tightening the bolts, pay attention not to tilt the bolt and clamp.
    5. Do not reuse the washer.

  1. A163353
    Temporarily install the common rail LH with the 2 bolts.

  1. A168840
    Temporarily install the 4 new injection pipes to the common rail and injectors.

  1. A062123E04
    Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces. If scratches or dents are present, replace the nozzle leakage pipe.
    Text in Illustration 
    *1
    Nozzle Leakage Pipe

  1. Set the nozzle leakage pipe and 5 new gaskets in place.

  1. A164167
    Temporarily install the nozzle leakage pipe with the 4 hollow screws and union bolt.

    HINT:
    To position the injectors, loosely tighten the 4 hollow screws and union bolt.

  1. A164165
    Tighten the 4 holder clamp bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. A168840
    Remove the 4 injection pipes.

  1. A163353
    Remove the 2 bolts and common rail LH.

  1. A165056
    Tighten the 4 hollow screws.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.

  1. A165057
    Tighten the union bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.


51. INSTALL FUEL INJECTOR RH (w/o DPF)

NOTICE:
Be sure to install the injector, holder clamp and bolt in their original positions.

  1. A164163
    Install 4 new injection nozzle seats to the cylinder head.

  1. Apply a light coat of clean engine oil to 4 new O-rings.

  1. A164164E03
    Install an O-ring to each injector as shown in the illustration.
    Text in Illustration 
    *1
    New O-Ring

  1. Insert the 4 injectors into the cylinder head.

    NOTICE:
    1. Insert the injector until it touches the nozzle seat surface.
    2. After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.
    3. Always return an injector to the same place it was removed from.

  1. For an injector that has been replaced with a new injector, register the injector compensation code (Click here).

  1. A164160E06
    Temporarily install 4 new washers and the 4 nozzle clamps with the 4 clamp bolts.
    Text in Illustration 
    *1
    New Washer
    *2
    Nozzle Holder Clamp
    *a
    Downward

    NOTICE:
    1. The fork portion of the nozzle holder clamp must be set to the injector.
    2. Before tightening the bolts, check that the nozzle holder clamp is set properly.
    3. To tighten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.
    4. When tightening the bolts, pay attention not to tilt the bolt and clamp.
    5. Do not reuse the washer.

  1. A168360
    Temporarily install the common rail RH with the 2 bolts.

  1. A168839
    Temporarily install the 4 new injection pipes to the common rail and injectors.

  1. A062123E04
    Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces. If scratches or dents are present, replace the nozzle leakage pipe.
    Text in Illustration 
    *1
    Nozzle Leakage Pipe

  1. Set the nozzle leakage pipe and 5 new gaskets in place.

  1. A164168
    Temporarily install the nozzle leakage pipe with the 4 hollow screws and union bolt.

    HINT:
    To position the injectors, loosely tighten the 4 hollow screws and union bolt.

  1. A164166
    Tighten the 4 holder clamp bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. A168839
    Remove the 4 injection pipes.

  1. A168360
    Remove the 2 bolts and common rail RH.

  1. A165023
    Tighten the 4 hollow screws.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.

  1. A165024
    Tighten the union bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.


52. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/ DPF)

  1. A271747
    Temporarily install 2 service stud bolts (8 mm x 1.25 pitch with a length of 30 mm or more) to the 2 locations shown in the illustration.

  1. A267299
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new cylinder head cover gasket LH and new No. 4 cylinder head cover gasket to the cylinder head cover LH.

    NOTICE:
    Remove any oil from the contact surface.

  1. Using the service stud bolts as guides, place the cylinder head cover LH on the cylinder head.

  1. Remove the 2 service stud bolts.

  1. A267297E01
    Temporarily install the cylinder head cover LH with the 18 bolts and 4 nozzle holder clamp seats. Tighten the 18 bolts and 4 nozzle holder clamp seats in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt
    V100136
    Nozzle Holder Clamp Seat

    HINT:
    After tightening the bolts, check that the bolts at step 16 and 24 are tightened to the specified torque.


53. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/ DPF)

  1. A271748
    Temporarily install 2 service stud bolts (8 mm x 1.25 pitch with a length of 30 mm or more) to the 2 locations shown in the illustration.

  1. A267298
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new cylinder head cover gasket RH and new No. 3 cylinder head cover gasket to the cylinder head cover RH.

    NOTICE:
    Remove any oil from the contact surface.

  1. Using the service stud bolts as guides, place the cylinder head cover RH on the cylinder head.

  1. Remove the 2 service stud bolts.

  1. A267295E01
    Temporarily install the cylinder head cover RH with the 19 bolts and 4 nozzle holder clamp seats. Tighten the 19 bolts and 4 nozzle holder clamp seats in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt
    V100136
    Nozzle Holder Clamp Seat

    HINT:
    After tightening the bolts, check that the bolts at step 16 and 25 are tightened to the specified torque.


54. INSTALL FUEL INJECTOR LH (w/ DPF)

NOTICE:
  1. Be sure to install the injector, holder clamp and bolt to their original positions.
  2. Before installing the injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head and injector. If there is foreign matter, remove it before installing the injector.

  1. A271223
    Install 4 new injection nozzle seats to the cylinder head.

  1. A203043E01
    Apply a light coat of clean engine oil to 4 new O-rings.
    Text in Illustration 
    *1
    New O-Ring

  1. Install the O-rings to each injector as shown in the illustration.

  1. Insert the 4 injectors into the cylinder head.

    NOTICE:
    1. Insert the injector until it touches the nozzle seat surface.
    2. After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.
    3. Always return an injector to the same place it was removed from.

  1. For an injector that has been replaced with a new injector, register the injector compensation code (Click here).

  1. A271222E01
    Temporarily install 4 new washers and the 4 nozzle holder clamps with the 4 clamp bolts.
    Text in Illustration 
    *1
    New Washer

    NOTICE:
    When temporarily installing the nozzle holder clamp bolt to the nozzle holder clamp, make sure that the bolt and clamp are not at an angle.

  1. A267323
    Temporarily install the common rail LH with the 2 bolts.

  1. A271636
    Temporarily install 4 new injection pipes to the common rail and injector.

  1. A271219
    Temporarily install the No. 2 nozzle leakage pipe and 4 used gaskets with the 4 injector hollow screws and 2 bolts.
    Text in Illustration 
    V100135
    Injector Hollow Screw
    V100136
    Bolt

  1. Tighten the 4 holder clamp bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Remove the 4 injection pipes.

  1. Remove the 2 bolts and common rail LH.

  1. Remove the 4 injector hollow screws and 4 gaskets.

  1. Remove the 2 bolts and No. 2 nozzle leakage pipe.


55. INSTALL FUEL INJECTOR RH (w/ DPF)

NOTICE:
  1. Be sure to install the injector, holder clamp and bolt to their original positions.
  2. Before installing the injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head and injector. If there is foreign matter, remove it before installing the injector.

  1. A271223
    Install 4 new injection nozzle seats to the cylinder head.

  1. A203043E01
    Apply a light coat of clean engine oil to 4 new O-rings.
    Text in Illustration 
    *1
    New O-Ring

  1. Install the O-rings to each injector as shown in the illustration.

  1. Insert the 4 injectors into the cylinder head.

    NOTICE:
    1. Insert the injector until it touches the nozzle seat surface.
    2. After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.
    3. Always return an injector to the same place it was removed from.

  1. For an injector that has been replaced with a new injector, register the injector compensation code (Click here).

  1. A271222E01
    Temporarily install 4 new washers and the 4 nozzle holder clamps with the 4 clamp bolts.
    Text in Illustration 
    *1
    New Washer

    NOTICE:
    When temporarily installing the nozzle holder clamp bolt to the nozzle holder clamp, make sure that the bolt and clamp are not at an angle.

  1. A267324
    Temporarily install the common rail RH with the 2 bolts.

  1. A271637
    Temporarily install 4 new injection pipes to the common rail and injector.

  1. A271215
    Temporarily install the No. 1 nozzle leakage pipe and 4 used gaskets with the 4 injector hollow screws and union bolt.
    Text in Illustration 
    V100135
    Injector Hollow Screw
    V100136
    Union Bolt

  1. Tighten the 4 holder clamp bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Remove the 4 injection pipes.

  1. Remove the 2 bolts and common rail RH.

  1. Remove the 4 injector hollow screws and 4 gaskets.

  1. Remove the union bolt and No. 1 nozzle leakage pipe.


56. REMOVE INTAKE MANIFOLD
  1. Remove the 16 bolts, 2 gaskets and intake manifold.

  1. Remove the 9 bolts, No. 1 intake manifold and gasket.

  1. Remove the 9 bolts, No. 2 intake manifold and gasket.


57. INSTALL CYLINDER HEAD COVER INSULATOR LH (w/ DPF)

58. INSTALL CYLINDER HEAD COVER INSULATOR RH (w/ DPF)

59. INSTALL NO. 2 FUEL PUMP BRACKET (w/ DPF)
  1. Install the No. 2 fuel pump bracket with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


60. INSTALL NOZZLE HOLDER GASKET LH (w/o DPF)

  1. A174978E02
    Press 4 new nozzle holder gaskets into the cylinder head cover LH.

    NOTICE:
    After installing the nozzle holder gasket, check that it does not protrude from the cylinder head cover.

    Text in Illustration 
    *1
    Nozzle Holder Gasket


61. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/o DPF)

  1. A164159
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.

  1. A174973E01
    Temporarily install the cylinder head cover with the 17 bolts. Tighten the 17 bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    After tightening the bolts, check that the bolts at step 11 and 19 are tightened to the specified torque.


62. INSTALL NOZZLE HOLDER SEAL LH (w/o DPF)
  1. Press 4 new holder seals into the cylinder head cover LH.


63. INSTALL OIL SEPARATOR ASSEMBLY
  1. Install a new gasket to the oil separator.

    NOTICE:
    Remove any oil from the contact surface.

  1. Install the oil separator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


64. INSTALL NOZZLE HOLDER GASKET RH (w/o DPF)

  1. A174978E02
    Press 4 new nozzle holder gaskets into the cylinder head cover RH.

    NOTICE:
    After installing the nozzle holder gasket, check that it does not protrude from the cylinder head cover.

    Text in Illustration 
    *1
    Nozzle Holder Gasket


65. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/o DPF)

  1. A164158
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.

  1. A174972E01
    Temporarily install the cylinder head cover with the 18 bolts. Tighten the 18 bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    After tightening the bolts, check that the bolts at step 11 and 20 are tightened to the specified torque.


66. INSTALL NOZZLE HOLDER SEAL RH (w/o DPF)
  1. Press 4 new holder seals into the cylinder head cover RH.


67. INSTALL OIL FILLER CAP GASKET

68. INSTALL OIL FILLER CAP SUB-ASSEMBLY

69. INSTALL SCAVENGING PUMP ASSEMBLY
  1. Install the scavenging pump with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


70. INSTALL OIL PUMP ASSEMBLY
  1. Install the oil pump with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


71. INSTALL REAR CRANKSHAFT OIL SEAL

  1. A164874E01
    Place the oil seal retainer on wooden blocks.

  1. Using SST and a hammer, tap in a new oil seal as shown in the illustration.

    SST
    09223-56010  

    Standard depth A:
    2.7 to 3.7 mm (0.106 to 0.147 in.)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap on the seal at an angle.


72. INSTALL REAR ENGINE OIL SEAL RETAINER

NOTICE:
When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.
A158674E01

  1. A164338E03
    Apply seal packing in a continuous line as shown in the illustration.

    Seal diameter:
    3.0 to 5.0 mm (0.118 to 0.197 in.)

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. Apply engine oil to the oil seal lip.

  1. Make sure that the lip of the oil seal is properly installed.

  1. A179123E01
    Install and uniformly tighten the 10 bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.
    2. When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.


73. INSTALL OIL REGULATOR ASSEMBLY
  1. Install the oil regulator with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


74. INSTALL INLET OIL PUMP PIPE
  1. Apply a light coat of engine oil to a new O-ring, and install it to the inlet oil pump pipe.

  1. Install the inlet oil pump pipe with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


75. INSTALL NO. 1 OIL PAN BAFFLE PLATE
  1. Install the No. 1 oil pan baffle plate with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


76. INSTALL NO. 1 OIL PAN SUB-ASSEMBLY

NOTICE:
When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.


A177348
  1. Install the cylinder block oil hole gasket.

  1. Apply a light coat of engine oil to 3 new O-rings and set the 3 O-rings to the oil regulator and scavenging pump.

  1. A177350E01
    Apply seal packing to the No. 1 oil pan as shown in the illustration.

    Standard seal diameter:
    3.5 to 4.0 mm (0.134 to 0.157 in.)

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. For the 3 bolt holes labeled with arrows, apply the seal packing on the outer edges. For the other bolt holes, apply the seal packing on the inner edges.
    2. Make sure to apply a continuous bead of seal packing as shown in the illustration. If the bead breaks, overlap 3 mm (0.118 in.) of seal packing and continue the bead.
    3. Remove any oil and old seal packing from the contact surface.
    4. Install the No. 1 oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
    5. Do not start the engine for at least 2 hours after installing.

  1. A174874E01
    Install the No. 1 oil pan and oil reflector plate with the 20 bolts and 2 nuts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    Bolt Length 
    Item
    Quantity
    Length
    Bolt A
    7
    70 mm (2.76 in.)
    Bolt B
    8
    20 mm (0.787 in.)
    Bolt C
    5
    30 mm (1.18 in.)


77. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Apply a light coat of engine oil to a new O-ring, and install it to the oil strainer.

  1. Install the oil strainer with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


78. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

NOTICE:
When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.


A177349

  1. A177351E01
    Apply seal packing to the No. 2 oil pan as shown in the illustration.

    Standard seal diameter:
    5.0 to 6.0 mm (0.197 to 0.236 in.)

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. For the bolt and pin holes, make sure to apply seal packing to the inner sides.
    2. Make sure to apply a continuous bead of seal packing as shown in the illustration. If the bead breaks, overlap 3.0 mm (0.118 in.) of seal packing and continue the bead.
    3. Remove any oil from the contact surface.
    4. Install the No. 2 oil pan within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.
    5. Do not start the engine for at least 2 hours after installing.

  1. Install the No. 2 oil pan with the 10 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


79. INSTALL OIL PAN DRAIN PLUG
  1. Install a new gasket and the oil pan drain plug.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }


80. INSTALL ENGINE OIL LEVEL SENSOR
  1. Install a new gasket and the sensor with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


81. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

  1. A177439E02
    Apply a light coat of engine oil to 2 new O-rings, and set them to the oil filter bracket.
    Text in Illustration 
    *1
    New O-Ring

  1. Install the oil filter bracket with the 3 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


82. INSTALL OIL FILTER ELEMENT

  1. A106167E08
    Clean the inside of the oil filter cap, its threads and its O-ring groove.

  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

  1. Set a new oil filter element in the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap by hand.

  1. A174854E02
    Using SST, tighten the oil filter cap.
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. Make sure that the oil filter is installed securely as shown in the illustration.
    2. Be careful that the O-ring does not get caught between any surrounding parts.

  1. A177436
    Install the No. 2 engine under cover seal to the No. 2 engine under cover with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


83. INSTALL OIL COOLER RELIEF VALVE ASSEMBLY
  1. Install a new gasket and the oil cooler relief valve.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


84. INSTALL OIL COOLER ASSEMBLY

  1. A170279
    Apply a light coat of engine oil to 2 new O-rings and a new oil cooler gasket, and set them to the oil cooler.

  1. A170278
    Install the oil cooler with the 2 bolts and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


85. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY
  1. Remove the adhesive from the threads of the oil pressure sender gauge and the bolt hole of the oil filter bracket.

  1. A161955E01
    Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Do not apply adhesive to the oil inlet port of the sensor.

  1. A170281
    Install the oil pressure sender gauge.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.

  1. Connect the oil pressure sender gauge connector.


86. INSTALL TIMING GEAR COVER SPACER (w/ Intercooler)
  1. Install the timing gear cover spacer with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


87. INSTALL CRANKSHAFT PULLEY

NOTICE:
This procedure is intended for removal/installation of the crankshaft pulley only. Do not use this procedure for removal/installation of the flywheel or the drive plate and ring gear.

  1. A174866E02
    Align the crankshaft pulley and the crankshaft knock pin, and temporarily install the crankshaft pulley with the 3 bolts.
    Text in Illustration 
    *1
    Service Hole
    *2
    Protrusion

  1. Install the 2 bolts to the bolt holes of the crankshaft rear side.

  1. Using a bar, turn the crankshaft until the crankshaft pulley service hole is a little to the right of bottom dead center.

  1. Install a 14 mm x 1.5 pitch service bolt with a length of 70 mm or more to the crankshaft pulley service hole, and hold the crankshaft using the timing chain cover protrusion.

  1. A179714E01
    Uniformly tighten the 3 bolts in 2 passes in the order shown in the illustration.

    Torque:
    115 N*m{ 1168 kgf*cm , 84 ft.*lbf }

  1. Remove the service bolt.


88. CONNECT NO. 2 OIL COOLER HOSE
  1. Align the white paint marks on the oil cooler hose and oil filter bracket and connect the hose. Then connect the other side to the water pump and attach the oil cooler hose to the clamp.

    NOTICE:
    Make sure to maintain a space between the oil cooler hose and crankshaft pulley, and the oil cooler hose and V-ribbed belt idler pulley.


89. CONNECT NO. 1 OIL COOLER HOSE
  1. Face the pink paint mark on the oil cooler hose toward the front side of the engine and connect the hose to the oil filter bracket. Then connect the other side to the water pump.

    NOTICE:
    Make sure to maintain a space between the oil cooler hose and crankshaft pulley.


90. INSTALL CRANKSHAFT POSITION SENSOR

A102906
  1. Apply a light coat of engine oil to the O-ring.

    NOTICE:
    When reusing the sensor, inspect the O-ring.
    If the O-ring has scratches or cuts, replace the sensor.

  1. A175725
    Install the sensor with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the sensor wire harness clamp.


91. INSTALL CAMSHAFT POSITION SENSOR

A124879
  1. Apply a light coat of engine oil to the O-ring.

    NOTICE:
    When reusing the sensor, inspect the O-ring.
    If the O-ring has scratches or cuts, replace the sensor.

  1. A163142
    Install the sensor with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the sensor connector.

← REASSEMBLY (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →