2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Fuel Injector Circuit

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

Refer to DTC P0300 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)
A166988E17
  1. Disconnect the fuel injector connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    a5-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    No. 2
    a1-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    No. 3
    a6-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    No. 4
    a2-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    No. 5
    a7-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    No. 6
    a3-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    No. 7
    a8-2 - Body ground
    Engine switch on (IG)
    11 to 14 V
    No. 8
    a4-2 - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
Go to step 4
OK


2. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
  1. Disconnect the fuel injector connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    a5-1 - Body ground
    Always
    10 kΩ or higher
    a5-1 - C46-86 (#10)
    Always
    Below 1 Ω
    No. 2
    a1-1 - Body ground
    Always
    10 kΩ or higher
    a1-1 - C46-109 (#20)
    Always
    Below 1 Ω
    No. 3
    a6-1 - Body ground
    Always
    10 kΩ or higher
    a6-1 - C46-85 (#30)
    Always
    Below 1 Ω
    No. 4
    a2-1 - Body ground
    Always
    10 kΩ or higher
    a2-1 - C46-108 (#40)
    Always
    Below 1 Ω
    No. 5
    a7-1 - Body ground
    Always
    10 kΩ or higher
    a7-1 - C46-84 (#50)
    Always
    Below 1 Ω
    No. 6
    a3-1 - Body ground
    Always
    10 kΩ or higher
    a3-1 - C46-107 (#60)
    Always
    Below 1 Ω
    No. 7
    a8-1 - Body ground
    Always
    10 kΩ or higher
    a8-1 - C46-83 (#70)
    Always
    Below 1 Ω
    No. 8
    a4-1 - Body ground
    Always
    10 kΩ or higher
    a4-1 - C46-106 (#80)
    Always
    Below 1 Ω
    for RHD 
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    a5-1 - Body ground
    Always
    10 kΩ or higher
    a5-1 - C45-86 (#10)
    Always
    Below 1 Ω
    No. 2
    a1-1 - Body ground
    Always
    10 kΩ or higher
    a1-1 - C45-109 (#20)
    Always
    Below 1 Ω
    No. 3
    a6-1 - Body ground
    Always
    10 kΩ or higher
    a6-1 - C45-85 (#30)
    Always
    Below 1 Ω
    No. 4
    a2-1 - Body ground
    Always
    10 kΩ or higher
    a2-1 - C45-108 (#40)
    Always
    Below 1 Ω
    No. 5
    a7-1 - Body ground
    Always
    10 kΩ or higher
    a7-1 - C45-84 (#50)
    Always
    Below 1 Ω
    No. 6
    a3-1 - Body ground
    Always
    10 kΩ or higher
    a3-1 - C45-107 (#60)
    Always
    Below 1 Ω
    No. 7
    a8-1 - Body ground
    Always
    10 kΩ or higher
    a8-1 - C45-83 (#70)
    Always
    Below 1 Ω
    No. 8
    a4-1 - Body ground
    Always
    10 kΩ or higher
    a4-1 - C45-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

4. INSPECT NO. 1 INTEGRATION RELAY (IG2)
  1. Inspect the No. 1 integration relay (IG2) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR)


← Fuel Pump Control Circuit (from Jan 2012)Starter Signal Circuit (from Jan 2012) →