CALIBRATION
Troubleshooting · Vehicles built Sep 2011 – Dec 2011
| ADJUST PARKING ASSIST MONITOR SYSTEM |
This parking assist monitor system can be set from the diagnostic screen of the display and navigation module display.
If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.
Part Name
Operation
Adjustment Item
Proceed to
Steering angle sensor
- Removal and installation of the Steering angle sensor
- Removal and installation of the connector of the Steering angle sensor
Steering angle neutral point
Click here
Steering angle setting
Click here
Steering angle sensor
Replacement
Steering angle neutral point
Click here
Steering angle setting
Click here
Parking assist ECU
Replacement
Parking assist ECU initialization
Step 2
Suspension, tires, etc.
The vehicle height changes because of suspension or tire replacement
Rear television camera optical axis (Camera position setting)
Step 3
Rear television camera assembly
- Replacement
- Installation angle of the rear television camera changes because of the removal and installation of the rear television camera, etc.
Rear television camera optical axis (Camera position setting)
Step 3
- HINT:
- The adjustment values stored while performing parking assist monitor system calibration are stored in the parking assist ECU.
- Removal and installation of the Steering angle sensor
| PARKING ASSIST ECU INITIALIZATION |
- HINT:
- Be sure to check for DTCs before performing this procedure (Click here).
Preparation for adjustment
Park the vehicle with the steering wheel centered.
Set a target bar for optical axis adjustment of the rear television camera.

- HINT:
- Only when adjusting the optical axis of the camera, create a target bar for adjustment.
- Dimension:
Area
Specification
A
825 to 835 mm (2.71 to 2.74 ft.)
B
1995 to 2005 mm (6.545 to 6.578 ft.)
Text in Illustration *1
Vehicle Center
*2
Target Bar for Back Camera Adjustment
*3
Vehicle End
*4
Front Side
- HINT:
- Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.787 to 1.181 in.) and 1995 to 2005 mm (6.545 to 6.578 ft.), respectively. Check the color on the display and navigation module display and choose a tape color which can be easily seen.
- Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
- Check that the back door is fully closed.
- Set a piece of tape on the ground as the target bar for adjustment. Its width and length are 20 to 30 mm (0.787 to 1.181 in.) and 1995 to 2005 mm (6.545 to 6.578 ft.), respectively. Check the color on the display and navigation module display and choose a tape color which can be easily seen.
Start diagnostic mode .
- for HDD (Click here).
- for DVD (Click here).
- NOTICE:
- Alignment must be performed with the engine running. For this reason, it is necessary to apply the parking brake, depress the brake pedal, and move the shift lever into the P position, and to exercise all other necessary caution to ensure that the vehicle does not begin moving unexpectedly.
- HINT:
- The displayed items may differ depending on vehicle specifications.
Select "Function Check/Setting" on the Service Menu screen.

Select "Camera Setting" on the Function Check/Setting screen.

Select "NEXT" on the SIGNAL CHECK screen.

Text in Illustration *1
w/ VGRS
*2
"EU/AUS" or "GCC/ZAF"
*3
Example
- NOTICE:
- When "CHK" (red) is displayed for any items on the SIGNAL CHECK screen, perform inspections using the SIGNAL CHECK screen (Click here).
- for HDD (Click here).
STEERING ANGLE SETTING
Perform the STEERING CENTER MEMORIZE operation.

- Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".
- HINT:
- When performing removal and installation, or replacement of the television camera, steering angle adjustment is not required.
- Check that the steering wheel is centered, and then select "STEERING CENTER MEMORIZE".
Perform the MAX STEERING ANGLE MEMORIZE operation.
- After adjusting the steering angle neutral point, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the BACK CAMERA POSITION SETTING screen.
- HINT:
- The "NEXT" button does not respond until the system stores the steering angle neutral point and maximum steering angle.
- HINT:
- It is also possible to start by initially turning the steering to the right side.
- When "MAX STEERING ANGLE MEMORIZE" is selected, a beep will sound to confirm that the steering adjustment values have been stored.
- The adjustment value will not be stored unless "MAX STEERING ANGLE MEMORIZE" is selected after turning the steering wheel side to side.
- When "BACK" is selected, the screen changes to SIDE VERIFY MODE without storing the set values.
- Even if no DTCs are detected, selecting "MAX STEERING ANGLE MEMORIZE" may not cause the adjustment value to be stored if the steering sensor is malfunctioning.
- If selecting "MAX STEERING ANGLE MEMORIZE" does not cause the adjustment value to be stored after adjusting the steering angle, replace the spiral with sensor cable sub-assembly.
- It is also possible to start by initially turning the steering to the right side.
- After adjusting the steering angle neutral point, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the BACK CAMERA POSITION SETTING screen.
BACK CAMERA POSITION SETTING

- HINT:
- When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
- If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after back door is closed).
- When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
Perform the roll angle adjustment.
- Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
- Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
Perform the vertical and horizontal position adjustment.
- Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
- Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
Select the "NEXT" button on the BACK CAMERA POSITION SETTING screen.
BACK VERIFY MODE

Check that A and the target adjustment bar are overlapping.
- If the steering angle neutral point is not aligned, perform the STEERING CENTER MEMORIZE and MAX STEERING ANGLE MEMORIZE operations.
- If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the camera position setting operation.
- If the steering angle neutral point is not aligned, perform the STEERING CENTER MEMORIZE and MAX STEERING ANGLE MEMORIZE operations.
Selecting "OK" will return the screen to the Service Menu screen, and complete the adjustment.
- HINT:
- The update is not completed until "OK" is selected.
- When "OK" is selected, a beep will sound to confirm that the rear camera aiming adjustment values have been stored.
- The update is not completed until "OK" is selected.
Finish diagnostic mode.
- for HDD (Click here).
- for DVD (Click here).
- for HDD (Click here).
| BACK CAMERA POSITION SETTING |
- HINT:
- Be sure to check for DTCs before performing this procedure (Click here).
Preparation for adjustment
Park the vehicle with the steering wheel centered.
Set a target bar for optical axis adjustment of the rear television camera.

- HINT:
- Only when adjusting the optical axis of the camera, create a target bar for adjustment.
- Dimension:
Area
Specification
A
825 to 835 mm (2.71 to 2.74 ft.)
B
1995 to 2005 mm (6.545 to 6.578 ft.)
Text in Illustration *1
Vehicle Center
*2
Target Bar for Back Camera Adjustment
*3
Vehicle End
*4
Front Side
- HINT:
- Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.181 in.) and 1995 to 2005 mm (6.545 to 6.578 ft.), respectively. Check the color on the multi-display and choose a tape color which can be easily seen.
- Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.
- Check that the back door is fully closed.
- Set a piece of tape on the ground as the target bar for adjustment. Its width and length should be 20 to 30 mm (0.787 to 1.181 in.) and 1995 to 2005 mm (6.545 to 6.578 ft.), respectively. Check the color on the multi-display and choose a tape color which can be easily seen.
Start diagnostic mode.
- for HDD (Click here).
- for DVD (Click here).
- NOTICE:
- Apply the parking brake, depress the brake pedal, move the shift lever to P, and ensure that the vehicle is not moving.
- HINT:
- The displayed items may differ depending on vehicle specifications.
Select "Function Check/Setting" on the "Service Menu" screen.

Select "Camera Setting" on the Function Check/Setting screen.

Select "BACK CAMERA SETTING" on the MODE SETTING screen.

- HINT:
- To select a grayed out item, select and hold the item for 2 seconds or more.
Select "NEXT" on the SIGNAL CHECK screen.

Text in Illustration *1
w/ VGRS
*2
"EU/AUS" or "GCC/ZAF"
*3
Example
- NOTICE:
- When "CHK" (red) is displayed for any items on the SIGNAL CHECK screen, selecting "NEXT" will not change the screen to the BACK CAMERA POSITION SETTING screen.
- When "CHK" (red) is displayed for any items on the SIGNAL CHECK screen, perform inspections using the SIGNAL CHECK screen (Click here).
- When "CHK" (red) is displayed for any items on the SIGNAL CHECK screen, selecting "NEXT" will not change the screen to the BACK CAMERA POSITION SETTING screen.
- for HDD (Click here).
BACK CAMERA POSITION SETTING

- HINT:
- When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
- If the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message is displayed even when the back door is closed, perform inspections according to Problem Symptoms Table (A back door open warning message is displayed even after back door is closed).
- When the back door is open, the "Back door is open. Do not use the rear view monitor when the back door is not completely closed." message will be displayed and camera position setting will not be possible.
Perform the roll angle adjustment.
- Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
- Select switches A and B to rotate C so that it is parallel to the target adjustment bar.
Perform the vertical and horizontal position adjustment.
- Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
- Select the directional switches D, E, F and G to move C so that the target adjustment bar is centered in C.
Select the "NEXT" button on the "BACK CAMERA POSITION SETTING" screen.
BACK VERIFY MODE

Check that A and the target adjustment bar are overlapping.
- If the steering angle neutral point is not aligned, perform the STEERING CENTER MEMORIZE and MAX STEERING ANGLE MEMORIZE operations.
- If A and the target adjustment bar are not aligned even if the tires are aligned straight ahead, perform the camera position setting operation.
- If the steering angle neutral point is not aligned, perform the STEERING CENTER MEMORIZE and MAX STEERING ANGLE MEMORIZE operations.
Selecting "OK" will return the screen to the Service Menu, and complete the adjustment.
- HINT:
- The update is not completed until "OK" is selected.
- When "OK" is selected, a beep will sound to confirm that the rear camera aiming adjustment values have been stored.
- The update is not completed until "OK" is selected.
Finish diagnostic mode.
- for HDD (Click here).
- for DVD (Click here).
- for HDD (Click here).