2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL FRONT UPPER CENTER BUMPER RETAINER
  1. Install the front upper center bumper retainer with the 3 bolts.


2. INSTALL HEADLIGHT ASSEMBLY LH
  1. for Halogen Headlight:
    (Click here)

  1. for HID Headlight:
    (Click here)


3. INSTALL HEADLIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


4. INSTALL FRONT BUMPER SIDE SUPPORT LH
  1. Attach the 3 clips to install the front bumper side support LH.

  1. Install the 2 screws.


5. INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure described for the LH side.


6. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH
  1. Install the front No. 2 bumper extension sub-assembly LH with the 4 nuts.

    Torque:
    67 N*m{ 683 kgf*cm , 49 ft.*lbf }


7. INSTALL FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


8. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
  1. Install the front bumper reinforcement sub-assembly with the 6 nuts.

    Torque:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }


9. INSTALL FRONT BUMPER ENERGY ABSORBER
  1. Install the front bumper energy absorber.


10. INSTALL FRONT BUMPER COVER

HINT:
For the front bumper cover with garnish, use the procedure described below.

  1. B232036
    w/ Headlight Cleaner System:
    Connect the headlight cleaner hose.

  1. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:
    Connect the No. 4 engine room wire connector.

  1. Attach the 10 claws to install the front bumper cover.

  1. Install the 3 clips, 4 screws and 4 bolts.

  1. Using a T30 "TORX" socket, install the 6 screws.


11. INSTALL RADIATOR GRILLE ASSEMBLY
  1. w/ Wide View Front Monitor System:

    1. Connect the connector.

  1. Attach the 2 clips and 8 claws to install the radiator grille assembly.

  1. Install the 3 screws.


12. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. Install the radiator support seal with the 7 clips.

    B180890E02


13. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
  1. Push in the clip to install the front fender splash shield sub-assembly LH.

  1. Install the 3 bolts and screw.


14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Push in the clip to install the front fender splash shield sub-assembly RH.

  1. Install the 3 bolts and 2 screws.


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for HID Headlight)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


16. ADJUST HEADLIGHT AIMING
  1. for Halogen Headlight:

    1. (Click here)

  1. for HID Headlight:

    1. (Click here)


17. ADJUST FOG LIGHT AIMING (w/ Fog Light)
(Click here)

18. INSPECT TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ TOYOTA Parking Assist-sensor System)
(Click here)
← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →