2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for HID Headlight)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


5. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. Remove the 7 clips and radiator support seal.

    B180890E02


6. REMOVE FRONT BUMPER WINCH COVER SUB-ASSEMBLY

  1. B302213
    Detach the 2 claws.

  1. Detach the 3 guides and remove front bumper winch cover sub-assembly.


7. REMOVE RADIATOR GRILLE ASSEMBLY

  1. B302174E01
    Put protective tape around the radiator grille assembly.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 3 screws.

  1. Detach the 2 clips and 8 claws, and remove the radiator grille assembly.

  1. w/ Wide View Front Monitor System:

    1. Disconnect the connector.


8. REMOVE FRONT BUMPER COVER

  1. Put protective tape around the bumper cover.

    B302214E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -

  1. Using a T30 "TORX" socket, remove the 6 screws.

    B313279E01

    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

  1. Remove the 3 clips, 4 screws and 4 bolts.

  1. Detach the 10 claws.

    B302215

  1. Disconnect the winch control wire connector and remove the front bumper cover.

  1. w/ Fog Light:
    Disconnect the No. 4 engine room wire connector and remove the front bumper cover.


9. REMOVE FRONT BUMPER EXTENSION LH

  1. B185487
    Remove the 3 bolts and front bumper extension LH.


10. REMOVE FRONT BUMPER EXTENSION RH

HINT:
Use the same procedure described for the LH side.


11. REMOVE FRONT BUMPER SIDE SUPPORT LH

  1. B313278
    Remove the 2 screws.

  1. Detach the 3 clips and remove the front bumper side support LH.


12. REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:
Use the same procedure described for the LH side.


13. REMOVE HEADLIGHT ASSEMBLY LH
  1. for Halogen Headlight:
    (Click here)

  1. for HID Headlight:
    (Click here)


14. REMOVE HEADLIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


15. REMOVE FRONT UPPER CENTER BUMPER RETAINER

  1. B302216
    Remove the 3 bolts and front upper center bumper retainer.

← REMOVAL (Sep 2011 – Dec 2011)DISASSEMBLY (Sep 2011 – Dec 2011) →