Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.
Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.
HINT:
Install the steering intermediate shaft assembly from the inside of the vehicle.
Install the clamp to the steering column hole cover.
3.
CONNECT STEERING ACTUATOR ASSEMBLY
Make sure that the power steering link assembly is centered.
Install the steering actuator assembly.
If installing a new steering actuator assembly: Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.
NOTICE:
Do not pull out the center lock pin.
If reinstalling the removed steering actuator assembly:
Slowly turn the spiral case clockwise until it locks.
Turn the spiral case two turns counterclockwise from the lock position.
Align the slit of the sliding yoke with the alignment mark (▲).
Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.
Align the matchmarks on the No. 2 steering intermediate shaft and steering actuator.
NOTICE:
Do not fold back the boot part of the steering hole cover or turn it excessively. If it is turned excessively, return it to its original position.
Do not turn the actuator body and the spiral case.
HINT:
Install the steering actuator from the inside of the vehicle.
Install the bolt.
Torque:
35 N*m{
360 kgf*cm
, 26 ft.*lbf
}
Using needle nose pliers, lock the clamp to the steering column hole cover to install it.
NOTICE:
Be careful when performing the operation as the clamp may not lock if the claws of the clamp are deformed.
Move the lock in the direction of the arrow and connect the steering actuator connector.
HINT:
When a new actuator is installed, remove the center lock pin.
21.
INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Using pliers, grip the claws of the clamp and install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
Connect the 5 connectors to the turn signal switch with spiral cable.
22.
INSTALL TILT AND TELESCOPIC SWITCH
Attach the claw to install the switch.
Connect the switch connector.
23.
INSTALL UPPER STEERING COLUMN COVER
Attach the claw to install the upper steering column cover.
Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.
24.
INSTALL LOWER STEERING COLUMN COVER
Attach the 2 claws to install the lower steering column cover.
NOTICE:
Do not damage the tilt and telescopic switch.
Install the 3 screws.
Torque:
1.5 N*m{
15 kgf*cm
, 13 in.*lbf
}
25.
INSTALL STEERING WHEEL ASSEMBLY
Align the matchmarks on the steering wheel assembly and steering main shaft assembly.
Text in Illustration
*a
Matchmark
Install the steering wheel assembly set nut.
Torque:
50 N*m{
510 kgf*cm
, 37 ft.*lbf
}
26.
INSTALL STEERING PAD
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one: Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.
Make sure that the horn sounds.
HINT:
If the horn does not sound, inspect the horn system.
27.
INSTALL LOWER NO. 2 STEERING WHEEL COVER
Attach the 2 claws to install the cover.
28.
INSTALL LOWER NO. 3 STEERING WHEEL COVER
Attach the 2 claws to install the cover.
29.
CHECK FRONT WHEELS FACING STRAIGHT AHEAD
30.
INSTALL FRONT WHEELS
31.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter (Click here).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).