2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL NO. 1 FUEL TANK HEAT INSULATOR

  1. A175034E01
    Install the heat insulator with the 4 clips.

  1. Install the fuel tube clamp to the heat insulator.


2. INSTALL FUEL TANK TO FILLER PIPE HOSE

  1. A176439E03
    Install the hose to the fuel tank as shown in the illustration.
    Text in Illustration 
    *1
    Fuel Tank Side Mark
    *2
    Hose Side Mark

    HINT:
    1. Align the fuel tank side mark with the hose side mark when installing the hose.

    2. A176441E06
      Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.

    Text in Illustration 
    *1
    Stopper


3. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Apply a light coat of gasoline or grease to a new gasket, and install it to the fuel tank.

  1. A176324E03
    Install the fuel suction with pump and gauge tube into the fuel tank.
    Text in Illustration 
    *1
    Protrusion
    *2
    Groove
    V100135
    Front

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

    HINT:
    Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.

  1. Put the retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.

  1. A260062E01
    Set SST on the retainer.
    SST
    09808-14030  

    HINT:
    1. Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.
    2. Securely attach the claws of SST to the protrusions of the retainer and fix SST in place.
    3. Install SST while pressing the claws of SST against the retainer (toward the center of SST).

  1. A260064E02
    Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank as shown in the illustration.
    SST
    09808-14030  
    Text in Illustration 
    *1
    Fuel Tank Side Mark
    *2
    Retainer Side Mark

    HINT:
    Fit the tips of SST onto the ribs of the retainer.


4. INSTALL FUEL TANK MAIN TUBE, FUEL TANK RETURN TUBE AND NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY

  1. A176320
    A118171E12
    Install the 3 fuel tank tubes with the 3 tube joint clips.

    NOTICE:
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the tube joint clips are on the collars of the fuel tube joints.
    4. After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.

    Text in Illustration 
    *1
    Fuel Tube Joint
    *2
    O-Ring
    *3
    Fuel Tube
    *4
    Tube Joint Clip
    *a
    CORRECT
    *b
    INCORRECT

  1. Install the 3 fuel tank tubes to the fuel tank.


5. INSTALL FUEL TANK SUB-ASSEMBLY
  1. Set the fuel tank on an engine lifter and raise the fuel tank.

    NOTICE:
    Do not allow the fuel tank to contact the vehicle, especially the differential.

  1. Raise the engine lifter.

  1. Install the 2 fuel tank bands with the 2 pins and 2 clips.

  1. Connect the 2 fuel tank bands with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


6. CONNECT FUEL TANK TO FILLER PIPE HOSE

  1. A181358E03
    Connect the hose to the filler pipe as shown in the illustration.
    Text in Illustration 
    *1
    Hose Side Mark
    *2
    Pipe Side Mark
    *a
    0 to 3 mm

    HINT:
    1. Install the hose so that the distance between the fuel tank inlet pipe side mark and fuel tank to filler pipe hose side mark is 0 to 0.3 mm (0 to 0.0118 in.) as shown in the illustration.

    2. A176441E06
      Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.

    Text in Illustration 
    *1
    Stopper


7. CONNECT FUEL TANK BREATHER TUBE

  1. A175066E02
    Connect the fuel tank breather tube to the filler pipe and push the retainer.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

    Text in Illustration 
    *1
    Retainer

    HINT:
    Push the parts together firmly until a "click" sound is heard.

  1. Attach the fuel tube clamp.


8. CONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY

  1. A175062E03
    Connect the fuel main tube and push the retainer.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

    Text in Illustration 
    *1
    Retainer
    *2
    Connector
    *3
    O-Ring
    *4
    Pipe
    *5
    Nylon Tube

    HINT:
    Push the parts together firmly until a "click" sound is heard.

  1. Attach the fuel tube clamp.


9. CONNECT NO. 2 FUEL TANK BREATHER TUBE

  1. A175064E03
    Connect the fuel tank breather tube and push the retainer.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

    Text in Illustration 
    *1
    Retainer
    *2
    Connector
    *3
    O-Ring
    *4
    Pipe
    *5
    Nylon Tube

    HINT:
    Push the parts together firmly until a "click" sound is heard.

  1. Attach the fuel tube clamp.


10. CONNECT FUEL TANK RETURN TUBE

  1. A176339E03
    Connect the fuel tank return tube and push the retainer.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

    Text in Illustration 
    *1
    Retainer
    *2
    Pipe
    *3
    Nylon Tube
    *4
    Connector
    *5
    O-Ring

    HINT:
    Push the parts together firmly until a "click" sound is heard.

  1. Attach the fuel tube clamp.


11. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

  1. A176337E03
    Connect the fuel tank main tube and push the retainer.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

    Text in Illustration 
    *1
    Retainer
    *2
    Pipe
    *3
    Nylon Tube
    *4
    Connector
    *5
    O-Ring

    HINT:
    Push the parts together firmly until a "click" sound is heard.

  1. Attach the fuel tube clamp.


12. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
  1. Install the fuel tank protector with the 5 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


13. INSTALL FUEL TANK CAP ASSEMBLY

14. INSTALL REAR FLOOR NO. 2 SERVICE HOLE COVER
  1. Connect the fuel pump and fuel sender gauge connector.

  1. Install the service hole cover with new butyl tape.

  1. w/ Rear Air Conditioning System:
    Install the air duct and 2 screws.


15. INSTALL FRONT FLOOR CARPET ASSEMBLY

16. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
  1. w/ Sliding Roof (Click here)
  2. w/o Sliding Roof (Click here)

17. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
  1. w/ Sliding Roof (Click here)
  2. w/o Sliding Roof (Click here)

18. INSTALL REAR NO. 2 SEAT ASSEMBLY
  1. for Face to Face Seat Type (Click here)
  2. except Face to Face Seat Type (Click here)

19. INSTALL REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)
(Click here)

20. INSTALL REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)
(Click here)

21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


22. CHECK SRS WARNING LIGHT
(Click here)

23. ADD FUEL

24. INSPECT FOR FUEL LEAK
  1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check that there are no leaks from the fuel system.
      If there are fuel leaks, repair or replace parts as necessary.

    5. Turn the ignition switch off.

    6. Disconnect the GTS from the DLC3.

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →