2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).


2. REMOVE FUEL TANK CAP ASSEMBLY

3. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

  1. A175014
    Remove the 5 bolts and fuel tank protector.


4. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

  1. A176306E01
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank main tube.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


5. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A176336E01
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank main tube.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


6. DRAIN FUEL
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    CAUTION:
    1. Do not smoke or be near an open flame when working on the fuel system.
    2. Secure good ventilation.
    3. Keep gasoline away from rubber or leather parts.


    HINT:
    A181429E01
    for Single Tank Type:
    If the fuel pump does not operate, remove the fuel tube joint clip and No. 1 fuel tube joint, and drain fuel from the port shown in the illustration.
    for Double Tank Type:
    If the fuel pump does not operate, remove the fuel tube joint clip and disconnect the fuel tank return tube, and drain fuel from the port shown in the illustration.


7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


8. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)
  1. Remove the rear No. 1 seat assembly RH (Click here).


9. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)
  1. Remove the rear No. 1 seat assembly LH (Click here).


10. REMOVE REAR NO. 2 SEAT ASSEMBLY
  1. for Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).

  1. except Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).


11. REMOVE REAR NO. 1 SEAT PROTECTOR

B184032E01
  1. Detach the 10 claws and remove the 2 seat protectors.


12. REMOVE REAR NO. 2 SEAT PROTECTOR

B184031E01
  1. Detach the 10 claws and remove the 2 seat protectors.


13. REMOVE REAR STEP COVER

B181673

HINT:
Use the same procedure to remove the step cover on the other side.

  1. Detach the 2 claws and remove the step cover.


14. REMOVE REAR DOOR SCUFF PLATE LH

B181674
  1. Remove the screw.

  1. Detach the 3 claws and 4 clips, and remove the scuff plate.


15. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


16. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Detach the 6 clips and remove the support plate.


17. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190187E01

HINT:
Use the same procedure to remove the rear seat cover cap on the other side.

  1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

    HINT:
    Tape the screwdriver tip before use.


18. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH
  1. w/ Sliding Roof:
    Remove the front quarter trim panel assembly LH (Click here).

  1. w/o Sliding Roof:
    Remove the front quarter trim panel assembly LH (Click here).


19. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH
  1. w/ Sliding Roof:
    Remove the front quarter trim panel assembly RH (Click here).

  1. w/o Sliding Roof:
    Remove the front quarter trim panel assembly RH (Click here).


20. REMOVE AIR DUCT PLUG (w/ Rear Air Conditioning System)

  1. B183333
    Detach the 2 claws and remove the plug.

    HINT:
    Use the same procedures for both sides.


21. REMOVE REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)

  1. B183334
    Remove the screw.

  1. Detach the claw and remove the guide.

    HINT:
    Use the same procedures for both sides.


22. REMOVE FRONT FLOOR CARPET ASSEMBLY

E157065
  1. Turn over the floor carpet.
    w/ Rear Air Conditioning System:

    HINT:
    Fold back the floor carpet so that the air duct can be removed.

    w/o Rear Air Conditioning System:

    HINT:
    Fold back the floor carpet so that the service hole cover can be removed.


23. REMOVE REAR FLOOR NO. 2 SERVICE HOLE COVER

  1. A181426
    w/ Rear Air Conditioning System:
    Remove the 2 screws and air duct.

  1. A181427
    Remove the service hole cover.

  1. A181387E01
    Disconnect the fuel pump and sender gauge connector.


24. DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Single Tank Type)

  1. A176308E01
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank breather tube.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


25. DISCONNECT FUEL TANK RETURN TUBE (for Single Tank Type)

  1. A176310E02
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank return tube.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


26. DISCONNECT FUEL TANK RETURN TUBE (for Double Tank Type)

  1. A176338E01
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank return tube.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


27. DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A175061E01
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank main tube.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


28. DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Double Tank Type)

  1. A175063E01
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank breather tube.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


29. DISCONNECT FUEL TANK BREATHER TUBE (for Single Tank Type)

  1. A176312E01
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank breather tube from the filler pipe.

    NOTICE:
    1. Do not use any tools in this procedure.
    2. Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the pipe and connector.


30. DISCONNECT FUEL TANK BREATHER TUBE (for Double Tank Type)

  1. A175065E02
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank breather tube from the filler pipe.

    NOTICE:
    1. Do not use any tools in this procedure.
    2. Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the pipe and connector.


31. DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Single Tank Type)

  1. A176314
    Disconnect the hose from the filler pipe.


32. DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Double Tank Type)

  1. A175067
    Disconnect the hose from the filler pipe.


33. REMOVE FUEL TANK SUB-ASSEMBLY
  1. Place a transmission jack under the fuel tank.

  1. A175024
    Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.

  1. Slowly lower the transmission jack slightly.


34. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

  1. A175028E01
    Remove the 3 fuel tube joint clips and pull out the 2 fuel tubes and No. 1 fuel tube joint.

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.

  1. A176315
    Remove the 2 fuel tubes from the fuel tank.


35. REMOVE FUEL TANK MAIN TUBE, FUEL TANK RETURN TUBE AND NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

  1. A176319E02
    Remove the 3 fuel tube joint clips and pull out the 3 fuel tubes.

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.

  1. A175070
    Remove the 3 fuel tubes from the fuel tank.


36. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

  1. A260062E01
    Set SST on the retainer.
    SST
    09808-14030  

    HINT:
    1. Securely attach the claws of SST to the protrusion of the retainer and fix SST in place.
    2. Install SST while pressing the claws of SST against the retainer (towards the center of SST).

  1. A260063E01
    Using SST, loosen the retainer.
    SST
    09808-14030  

    NOTICE:
    1. Do not use any tools other than those specified in this operation. Damage to the retainer or the fuel tank may result.
    2. While pressing down on SST so that the claws of SST do not slip off the protrusion of the retainer, turn the retainer counterclockwise to loosen it.

    HINT:
    The protrusion of the retainer fit in the ends of SST.

    Text in Illustration 
    V100135
    Turn

  1. Remove the retainer while holding the fuel suction tube assembly by hand.

  1. Remove the gasket from the fuel tank.


37. REMOVE FUEL TANK TO FILLER PIPE HOSE

  1. A176316
    Remove the hose from the fuel tank.


38. REMOVE NO. 1 FUEL TANK HEAT INSULATOR

  1. A175033E01
    Remove the fuel tube clamp from the heat insulator.

  1. Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the heat insulator.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →