2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL NO. 2 AMPLIFIER BRACKET

  1. B181518E01
    Set the aligning protrusions of the bracket labeled A, into the holes of the amplifier.

  1. Install the bracket with the 2 screws labeled B.

    Torque:
    3.0 N*m{ 30 kgf*cm , 26 in.*lbf }


2. INSTALL NO. 1 AMPLIFIER BRACKET

  1. B181517E01
    Set the aligning protrusions of the bracket labeled A, into the holes of the amplifier.

  1. Install the bracket with the 2 screws labeled B.

    Torque:
    3.0 N*m{ 30 kgf*cm , 26 in.*lbf }


3. INSTALL AMPLIFIER COVER

  1. B181513
    Attach the 3 clips to install the cover.


4. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

  1. B181514
    Install the amplifier with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 3 connectors.


5. INSTALL FRONT FLOOR CARPET ASSEMBLY

  1. B186248
    Open the tail gate and back door, insert the carpet into the cabin from the rear, and install it to the floor.

  1. Attach the 2 clips and 8 claws.

    B183331


6. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)
  1. Install the rear console box (Click here).


7. INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)
  1. Install the cooling box assembly (Click here).


8. INSTALL REAR NO. 2 SEAT PROTECTOR

  1. B184595
    Attach the clip and 4 claws to install the protector.

    HINT:
    Use the same procedures to install the protector on the other side.


9. INSTALL REAR NO. 1 SEAT PROTECTOR

  1. B186247
    Attach the clip and 4 claws to install the protector.

    HINT:
    Use the same procedures to install the protector on the other side.


10. INSTALL REAR AIR DUCT GUIDE

  1. B183334
    Attach the claw to install the guide.

  1. Install the screw.

    HINT:
    Use the same procedures for both sides.


11. INSTALL AIR DUCT PLUG

  1. B183333
    Attach the 2 claws to install the plug.

    HINT:
    Use the same procedures for both sides.


12. INSTALL AIR HEATER GUIDE

  1. B183336
    Install the guide with the 2 screws.

    HINT:
    Use the same procedures for both sides.


13. INSTALL NO. 2 AIR DUCT PLUG

  1. B183335
    Attach the 4 claws to install the 2 plugs.

    HINT:
    Use the same procedures for both sides.


14. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


15. INSTALL REAR DOOR SCUFF PLATE LH

B181674
  1. Attach the 3 claws and 4 clips to install the scuff plate.

  1. Install the screw.


16. INSTALL REAR STEP COVER

B181673

HINT:
Use the same procedure to install the step cover on the other side.

  1. Attach the 2 claws to install the step cover.


17. INSTALL COWL SIDE TRIM BOARD RH

B180022
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


18. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182552
  1. Attach the 4 claws to install the No. 2 instrument panel under cover.


19. INSTALL COWL SIDE TRIM BOARD LH

B181911
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


20. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182553
  1. Connect the connectors.

  1. Attach the 3 claws to install the No. 1 instrument panel under cover.

  1. Install the 2 screws.


21. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


22. INSTALL FRONT DOOR SCUFF PLATE LH

B181682
  1. Attach the 7 claws and 4 clips to install the scuff plate.


23. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B186358
  1. Connect the connector.

  1. Attach the 6 claws to install the instrument side panel.


24. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B182551
  1. Attach the 6 claws to install the instrument side panel.


25. INSTALL INSTRUMENT SIDE PANEL LH

B181911
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


26. INSTALL REAR NO. 1 SEAT ASSEMBLY RH

B181161E01
  1. Temporarily install the seat assembly with the 4 bolts.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Tighten the bolts in the order shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. B181160
    w/ Rear Seat Side Airbag:
    Connect the connector.

  1. w/ Seat Heater System:
    Connect the connector.


27. INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER

B181159
  1. Attach the 2 clips and 2 claws to install the cover.


28. INSTALL REAR NO. 1 SEAT CUSHION HINGE COVER

B181158
  1. Attach the 2 clips and 2 claws to install the cover.


29. INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER
  1. Return the seat to the upright position.

  1. B258449
    Attach the 7 claws to install the cover.


30. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER

B258447
  1. Attach the 6 claws to install the cover.


31. INSTALL REAR NO. 1 SEAT ASSEMBLY LH

B181219E01
  1. Temporarily install the seat assembly with the 4 bolts.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Tighten the bolts in the order shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. B184034
    w/ Rear Seat Side Airbag:
    Connect the connector.

  1. w/ Seat Heater System:
    Connect the connector.


32. INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER

B181217
  1. Attach the 2 clips and 2 claws to install the cover.


33. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER

B181218
  1. Attach the 2 clips and 2 claws to install the cover.


34. INSTALL REAR NO. 5 SEAT CUSHION HINGE COVER
  1. Return the seat to the upright position.

  1. B261018
    Attach the 7 claws to install the cover.


35. INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER

B258451
  1. Attach the 6 claws to install the cover.


36. INSTALL FRONT SEAT ASSEMBLY RH
  1. for Manual Seat:
    Install the front seat assembly RH (Click here).

  1. for Power Seat:
    Install the front seat assembly RH (Click here).

    HINT:
    Use the same procedures described for the LH side.


37. INSTALL FRONT SEAT ASSEMBLY LH
  1. for Manual Seat:
    Install the front seat assembly LH (Click here).

  1. for Power Seat:
    Install the front seat assembly LH (Click here).


38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


39. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →